586463

Pioneer VSX-930 K-S Manual

107
Zoom out
Zoom in
Previous page
1/142
Next page
107
The System Setup and Other Setup menus
13
In case of VSX-830
! Default setting: 5.2ch
1 Select ‘Speaker System’ from the Manual SP Setup menu.
See Making receiver settings from the System Setup menu on page 106 if you’re not already at this screen.
2 Select the speaker system setting.
! 5.2ch – Select when connecting surround speaker and playing a maximum 5.2 ch surround.
! Front Bi-Amp – Select this setting if you’re bi-amping your front speakers (see Bi-amping your speakers on
page 40 ).
3 When ‘Setting Change?’ is displayed, select Yes.
If No is selected, the setting is not changed.
You will return to the Manual SP Setup menu.
Speaker Setting
In case of VSX-1130/VSX-930
Use this setting to specify your speaker configuration (size, number of speakers and crossover frequency). It
is a good idea to make sure that the settings made in Automatically conducting optimum sound tuning (Full
Auto MCACC) on page 57 are correct. Note that this setting applies to all MCACC presets, and cannot be set
independently.
1 Select ‘Speaker Setting’ from the Manual SP Setup menu.
2 Choose the set of speakers that you want to set, then select a speaker size.
Use k/l to select the size (and number) of each of the following speakers:
! SW – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES
is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you
want deeper bass (the bass frequencies that would normally come out the front and center speakers are also
routed to the subwoofer). If you did not connect a subwoofer choose NO (the bass frequencies are output
from other speakers).
— If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers
and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker
placement of your room you may actually experience a decrease in the amount of bass due low frequency
cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results,
listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL
alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to
route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
! Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass frequencies to the subwoofer.
! Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect a center speaker, choose NO
(the center channel is sent to the front speakers).
! TMd – Select LARGE if your top middle speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. When setting up the Dolby Enabled Speaker on
the front speaker, please select Dolby Sp (Front). When setting up the Dolby Enabled Speaker on the sur-
round speaker, please select Dolby Sp (Surr). If you didn’t connect the top middle speakers, choose NO (the
top middle channel is sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 7.2ch/5.2.2ch.
— If you change the setting from Dolby Sp (Surr) or Dolby Sp (Front) to SMALL or LARGE, the set value
for Speaker Distance may be changed. This is because the maximum value of Speaker Distance when
set to Dolby Sp (Surr) or Dolby Sp (Front) is bigger than the maximum value of Speaker Distance when
set to SMALL or LARGE. If the value of Speaker Distance set to Dolby Sp (Surr) or Dolby Sp (Front)
exceeds the maximum value of Speaker Distance for SMALL or LARGE, Speaker Distance for SMALL or
LARGE is set to its maximum value.
! FW – Select LARGE if your front wide speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect front wide speakers, choose
NO (the front wide channel is sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 7.2ch SB/FW.
— If the surround speakers are set to NO, this setting will automatically be set to NO.
! Surr – Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send
bass frequencies to the other speakers or subwoofer. If you didn’t connect surround speakers choose NO (the
sound of the surround channels is sent to the front speakers or a subwoofer).
! SB – Select the number of surround back speakers you have (one, two or none). Select LARGEx2 or LARGEx1 if your
surround back speakers reproduce bass frequencies effectively. Select SMALLx2 or SMALLx1 to send bass frequen-
cies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose NO.
— You can adjust this setting only when Speaker System setting is 7.2ch/5.2.2ch, 7.2ch SB/FW or
Speaker B.
— If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
If you select NO for the subwoofer, the front speakers will automatically be fixed to LARGE. Also, the center, top
middle, surround, surround back and front wide speakers can’t be set to LARGE if the front speakers are set to
SMALL. In this case, all bass frequencies are sent to the subwoofer.
3 Select ‘X. OVER’ and set the crossover frequency.
Frequencies below this point will be sent to the subwoofer (or LARGE speakers).
! This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or
the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff
will be for bass sounds in the LFE channel.
! With Full Auto MCACC setup or Auto MCACC setup (ALL or Speaker Setting), the setting here will not
apply and the crossover frequency will be automatically set. Crossover frequency is a frequency aimed at
achieving the optimal sound field taking into account the bass capacity of all connected speakers and human
aural characteristics.
4 When you’re finished, press RETURN.
You will return to the Manual SP Setup menu.
　
… 107 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-930 K-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-930 K-S in the language / languages: English as an attachment in your email.

The manual is 20,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-930 K-S

Pioneer VSX-930 K-S User Manual - German - 146 pages

Pioneer VSX-930 K-S User Manual - Dutch - 146 pages

Pioneer VSX-930 K-S User Manual - French - 145 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info