491803

Pioneer VSX-922K Manual

89
Zoom out
Zoom in
Previous page
1/109
Next page
89
13
FAQ
Professional Calibration EQ graphical output
Symptom Remedy
The reverb characteristics graph
after EQ calibration does not appear
entirely flat.
There are cases where the graph does not appear flat (even when selecting ALL CH ADJ
in the Auto MCACC Setup) due to adjustments made to compensate for room character-
istics to achieve optimal sound.
Areas of the graph may appear identical (before and after) when there is little or no
adjustment needed.
The graph may appear to have shifted vertically when comparing before and after mea-
surements.
EQ adjustments made using the
Manual MCACC setup do not appear
to change the reverb characteristics
graph after EQ calibration.
Despite level adjustments being made, the filters used for analysis may not display these
adjustments in the reverb characteristics graph after EQ calibration. However, these
adjustments are taken into account by the filters dedicated to overall system calibration.
Lower frequency response curves do
not seem to have been calibrated for
SMALL speakers.
Low frequencies used in bass management (the subwoofer channel) will not change for
speakers that have been specified as SMALL in the configuration, or do not output these
frequencies.
Calibration is performed, but due to your speakers’ low frequency limitations, no measur-
able sound is output for display.
Display
Symptom Remedy
The display is dark or off. Press DIMMER repeatedly to select a different brightness.
The OSD screen is not displayed. The OSD screen is not displayed unless the receiver and TV are connected using an
HDMI cable. If the TV does not support HDMI, perform the various operations and make
the settings while watching the display on the receiver’s front panel.
You can’t get DIGITAL to display
when using SIGNAL SEL.
Check the digital connections and make sure that the digital inputs are assigned cor-
rectly (see The Input Setup menu on page 34).
2 DIGITAL or DTS does not light
when playing Dolby/DTS software.
These indicators do not light if playback is paused.
Check the playback (especially the digital output) settings of the source component.
When playing Dolby Digital or DTS
sources, the receiver’s format indica-
tors do not light.
Check that the player is connected using a digital connection.
Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
page 46).
Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to
PCM.
Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is
selected.
When playing certain discs, none of
the receiver’s format indicators light.
The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on
what audio tracks are recorded on the disc.
When playing a disc with the listen-
ing mode set to Auto Surround or
ALC, 2 Pro Logic II or DTS Neo:6
appear on the receiver.
Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
page 46).
If a two channel soundtrack is currently playing (including Dolby Surround encoded),
then this is not a malfunction. Check the disc packaging for details about the audio
tracks available.
During playback of DVD-Audio, the
display shows PCM.
This will occur when playing DVD-Audio material over the HDMI connection. This is not a
malfunction.
Symptom Remedy
The power turns off automatically
and some indicator flashes, or some
indicator flashes and the power does
not turn on.
See the Power section (page 86).
Remote control
Symptom Remedy
Cannot be remote controlled. Set the remote control unit’s remote control mode so that it matches the setting on the
main unit (see Operating multiple receivers on page 65).
Check whether the receiver’s remote control mode is properly set (see Remote Control
Mode Setup on page 83).
Try replacing the batteries in the remote control (see Loading the batteries on page 7).
Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see
Operating range of remote control unit on page 7).
Check that there are no obstacles between the receiver and the remote control.
Make sure that there is no fluorescent or other strong light shining on to the remote
sensor.
Other components can’t be operated
with the system remote.
If the battery ran down, the preset codes may have been cleared. Re-enter the preset
codes.
The preset code may be incorrect. Redo the procedure for entering preset codes.
When commands from the remote control units of other devices are registered using the
learning function, in some cases they may not be learned properly. In this case, register
the commands again using the learning function (see page 66). If they still do not work,
they may be in a special format that cannot be registered on this receiver’s remote con-
trol. Operate the device using another remote control.
HDMI
Symptom Remedy
The HDMI indicator blinks continu-
ously.
Check all the points below.
No picture or sound. This receiver is HDCP-compatible. Check that the components you are connecting are
also HDCP-compatible. If they are not, please connect them using the component or
composite video jacks.
Depending on the connected source component, it’s possible that it will not work with
this receiver (even if it is HDCP-compatible). In this case, connect using the component
or composite video jacks between source and receiver.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
If video images do not appear on your TV, try adjusting the resolution, Deep Color or other
setting for your component.
While analog video signals are being output over HDMI, use a separate connection for
audio output.
To output signals in Deep Color, use an HDMI cable (High Speed HDMI
®
Cable) to con-
nect this receiver to a component or TV with the Deep Color feature.
… 89 …


Need help? Post your question in this forum.

Forumrules
1

Forum

pioneer-vsx-922k

Reset search

  • Bonjour, je suis le possesseur du modèle VSX 922 k avec lequel je connais des problèmes. Il semblerait que le souci vienne de la "Digital Main Board". J'ai fait de multiples recherches pour trouver et changer cette pièce.
    J'ai eu pour réponse, "cette pièce n'est plus disponible"...
    Des internautes m'ont indiqués qu'il existait un moyen de le démarrer en mode sécurité.
    Pouvez-vous me confirmer cette possibilité et le moyen de la mettre en œuvre.
    Je vous remercie de me tenir informé.
    Vous souhaitant bonne réception.
    Cordialement, Thierry SAGET. Submitted on 13-7-2021 at 21:08

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-922K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-922K in the language / languages: English as an attachment in your email.

The manual is 6,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-922K

Pioneer VSX-922K Quick start guide - English, German - 44 pages

Pioneer VSX-922K User Manual - German - 113 pages

Pioneer VSX-922K Quick start guide - Dutch - 44 pages

Pioneer VSX-922K User Manual - Dutch - 111 pages

Pioneer VSX-922K Quick start guide - French - 44 pages

Pioneer VSX-922K User Manual - French - 112 pages

Pioneer VSX-922K Quick start guide - Italian, Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info