455247
65
Zoom out
Zoom in
Previous page
1/84
Next page
Controlling the rest of your system
11
65
En
English
Français
Deutsch
Nederlands
Italiano
Español
5 Use
/
(cursor up/down) to select the
manufacturer’s name from the list then press
ENTER.
6 Use
/
(cursor up/down) to select the
proper code from the list, then try using this
remote control with your component.
The code should start with the component type
(for example,
DVD 009
). If there is more than
one, start with the first one.
To try out the remote control, switch the
component on or off (into standby) by pressing
SOURCE
. If it doesn’t seem to work, select
the next code from the list (if there is one).
VSX-915 only
– If you can’t find or properly
enter a preset code, you can still teach the
remote individual commands from another
remote control (see
Programming signals
from other remote controls
below).
7 If your component is controlled
successfully, press ENTER to confirm.
The remote LCD display shows
OK
.
Programming signals from other
remote controls
VSX-915 model only
If the preset code for your component is not
available, or the available preset codes do not
operate correctly, you can program signals
from the remote control of another
component. This can also be used to program
additional operations (buttons not covered in
the presets) after assigning a preset code.
1 While pressing the RECEIVER button,
press and hold the 1 button.
The remote LCD display shows
SETUP
.
2 Press the MULTI CONTROL button for the
component you want to control.
The LCD on the remote displays the
component you want to control.
1
3 Use
/
(cursor left/right) to select
LEARN
then press
ENTER
.
PRES KEY
shows in the LCD display.
To exit or cancel press
RECEIVER
.
4 Point the two remote controls towards
each other then press the button that will be
doing the learning on this receiver’s remote
control.
PRES KEY
starts flashing to indicate the
remote is ready to accept a signal.
The remote controls should be 3–5 cm
apart.
5 Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s remote
control.
For example, if you want to learn the playback
control signal, press and hold
for a couple of
seconds. The LCD display will show
OK
if the
operation has been learned.
If for some reasons the operation hasn’t been
learned the LCD will display
ERROR
briefly and
then display
PRES KEY
again. If this happens,
keep pressing the (teaching) button as you vary
the distance between the two remotes, until
the LCD display shows
OK
.
2
Note
1• You can’t assign the
RECEIVER
button.
TV CONTROL
buttons (
TV
,
TV VOL +/–
,
TV CH +/–
and
INPUT SELECT
) can only be learned after selecting
TV CONT
.
2• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer
together or farther apart.
• If the remote LCD shows
ERROR
, it may also mean the memory is full. See
Erasing one of the remote control button settings
below to erase a programmed button you’re not using to free up more memory.
3 – 5 cm
+
10
INPUT ATTFL DIMMER SR
DISC
RECEIVER
MULTI CONTROL
SOURCE
INPUT
SELECT
SETUP
ENTER
TV CONTROL
RECEIVER CONTROL
SHIFT
VOL
DVD/LD TV/SAT DVR/VCR TV CONT
CD
TUNE
TUNE
ST ST
STANDRAD
LEVEL EFFECT
TEST TONE
CH SELECT
ADV. SURR STEREO SLEEP
INPUT
SELECT
TV CH
DTV ON/OFF
TUNER
DISPLAY
MPX
AUDIO
CH RETURN
SUBTITLE
MIDNIGHT/
LOUDNESS
DTV INFOREC MUTE
TV VOL
CD-R/TAPE
TUNER RECEIVER
ENTER
REC STOP
HDD
CH
CH
DVD
D.ACCESS
TOP MENU
DTV MENU
CLASS
MENU
BAND
RETURN
GUIDE
T.EDIT
MCACC
SETUP
RECEIVER
VSX_815-915.book.fm 65 ページ 2005年3月1日 火曜日 午前10時22分
Downloaded from www.Manualslib.com manuals search engine
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-915-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-915-K in the language / languages: English as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-915-K

Pioneer VSX-915-K User Manual - English - 76 pages

Pioneer VSX-915-K User Manual - German - 150 pages

Pioneer VSX-915-K User Manual - Dutch - 150 pages

Pioneer VSX-915-K User Manual - French - 150 pages

Pioneer VSX-915-K User Manual - Italian - 150 pages

Pioneer VSX-915-K User Manual - Spanish - 150 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info