574068
104
Zoom out
Zoom in
Previous page
1/123
Next page
Additional information
12
104
En
Important information regarding the HDMI connection
There are cases where you may not be able to route HDMI signals through this receiver (this depends on the HDMI-
equipped component you are connecting–check with the manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals proper ly through this receiver (from your component), please try one of the
following configurations when connecting up.
Configuration A
Use component video cables to connect the video output
of your HDMI-equipped component to the receiver’s
component video input. The receiver can then convert the
analog component video signal to a digital HDMI signal
for transmission to the display. For this configuration,
use the most convenient connection (digital is
recommended) for sending audio to the receiver. See the
operating instructions for more on audio connections.
Note
•The picture quality will change slightly during
conversion.
Configuration B
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most
convenient connection (digital is recommended) for
sending audio to the receiver. See the operating
instructions for more on audio connections. Set the
display volume to minimum when using this
configuration.
Note
•If your display only has one HDMI terminal, you can
only receive HDMI video from the connected
component.
•Depending on the component, audio output may be
limited to the number of channels available from the
connected display unit (for example audio output is
reduced to 2 channels for a monitor with stereo audio
limitations).
If you want to switch the input function, you’ll have to
switch functions on both the receiver and your
display unit.
Since the sound is muted on the display when using
the HDMI connection, you must adjust the volume on
the displa
y every tim
e you switch input functions.
Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example), or the
video quality may just be poor (with some video game units, for example). The picture quality may
also depend on the settings, etc. of your display device. Switch off the video converter and reconnect
the source and display device using the same type of connection (component, S-Video or
composite), then start playback again.
• If the problem still persists when connecting your HDMI component directly to your monitor,
please consult the component or monitor manual or contact the manufacturer for support.
HDCP ERROR shows in the
display.
• Che
ck whether or not the connected component is compatible with HDCP. If it is not compatible
with HDCP, reconnect the source device using a different type of connection (component, S-Video
or composite). Some components that are compatible with HDCP still cause this message to be
displayed, but so long as there is no problem with displaying video, this is not a malfunction.
Amp-linked operation not
possible using KURO LINK
function.
• Check the HDMI connections.
• The cable may be damaged.
• Select ON for the KURO LINK setting (see KURO LINK Setup on page 64).
• Turn the TV’s power on before turning on this receiver’s power.
• Set the TV side KURO LINK setting to ON.
VSX-9140TXH only: Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to HDMI
OUT 1. Then turn on
first the TV’s power, then this receiver’s power.
Symptom Remedy
VSX-9140TXH_CUXJ.book 104 ページ 2009年4月16日 木曜日 午前10時36分
104


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-9140TXH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-9140TXH in the language / languages: English as an attachment in your email.

The manual is 11,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info