Manual Pioneer VSX-9140TXH (page 80 of 123) (English)

574068

Zoom out

Zoom in

1/123

The Advanced MCACC menu

• If you see an ERR message (or the speaker

configuration displayed isn’t correct), there may be a

problem with the speaker connection.

If selecting RETRY doesn’t work, tur n off the power

and check the speaker connections. If there doesn’t

seem to be a problem, you can simply use / to

select the speaker and / to change the setting

and continue.

•If Reverse Phase is displayed, the speaker’s wiring

(+ and –) may be inverted. Check the speaker

connections.

– If the connections were wrong, turn off the power,

disconnect the power cord, then reconnect properly.

After this, perform the Full Auto MCACC procedure

again.

– If the connections were right, select GO NEXT and

continue.

8 Make sure ‘

’ is selected, then press

ENTER

A progress report is displayed on-screen while the

receiver outputs more test tones to determine the

optimum receiver settings for channel level, speaker

distance, and Acoustic Calibration EQ.

Again, try to be as quiet as possible while this is

happening. It may take 3 to 7 minutes.

•If you selected a STAND.WAVE Multi-Point setup

(in step 2), you will be asked to place the mic at the

2nd and 3rd reference points before finally placing it

at your main listening position.

9 The Auto MCACC Setup procedure is completed and

the

Advanced MCACC

menu reappears automatically.

The settings made in the Auto MCACC Setup should give

you excellent surround sound from your system, but it is

also possible to adjust these settings manually using the

Manual MCACC setup menu (starting below) or Manual

SP Setup menu (starting on page 90).

You can also choose to view the settings by selecting

individual parameters from the MCACC Data Check

screen:

• Speaker Setting – The size and number of speakers

you’ve connected (see page 91 for more on this)

• Channel Level – The overall balance of your speaker

system (see page 81 or 92 for more on this)

• Speaker Distance – The distance of your speakers

from the listening position (see page 82 or 93 for

more on this)

• Standing Wave – Filter settings to control lower

‘boomy’ frequencies (see page 82 for more on this)

• Acoustic Cal EQ – Adjustments to the frequency

balance of your speaker system based on the

acoustic characteristics of your room (see page 83

for more on this)

• Output PC – The data transfer mode with the

connected computer is set. The graphs of the reverb

characteristics before and after calibration and the

various MCACC parameters can be checked (see

Output PC on page 88 for mor e on this).

Press RETURN after you have finished checking each

screen. Wh

en you’re fin

ished, select RETURN to go back

to the HOME MENU.

Be sure to disconnect the microphone from this receiver

upon completion of the Auto MCACC Setup.

Manual MCACC setup

You can use the settings in the Manual MCACC setup

menu to make detailed adjustments when you’re more

familiar with the system. Before making these settings,

you should have already completed Automatically setting

up for surround sound (Auto MCACC) on page 41.

You only need to make these settings once (unless you

change the placement of your current sp eaker system or

add new speakers).

CAUTION

• The test tones used in the Manual MCACC setup are

output at high volume.

Note

1If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase (dipole speakers, reflective

speakers, etc.), Reverse Phase may be displayed even if the speakers are properly connected.

2• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm will end up with different size

settings. You can correct the setting manually using the Manual speaker setup on page 90.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking

delay and room characteristics into account) and generally does not need to be changed.

• If Auto MCACC Setup measurem

nt results are incorrect due to the interaction of the speakers and viewing environment, we recommend

adjusting the settings manually.

Now Analyzing...

1b.Auto MCACC

A/V RECEIVER

Exit Cancel

Subwoofer Check :

Now Analyzing... 5/9

Surround Analysis

1b.Auto MCACC

A/V RECEIVER

Exit Cancel

Speaker System : OK

Channel Level :

Speaker Distance :

Standing Wave :

Reverb :

Aco Cal EQ Pro :

3 Since the distance measurements have been set according to the sound characteristics of your speakers, there are cases where (for optimal

surround sound) the actual distance may differ from the speaker distance setting.

VSX-9140TXH_CUXJ.book 80 ページ２００９年４月１６日　木曜日　午前１０時３６分

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-9140TXH in the language / languages: English as an attachment in your email.

The manual is 11,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-9140TXH Manual

Product: