574068
73
Zoom out
Zoom in
Previous page
1/123
Next page
Controlling the rest of your system
09
73
En
Chapter 9:
Controlling the rest of your system
Operating multiple receivers
The remote control included with this receiver can be
used to operate up to three other receivers (of the same
model as this receiver) in addition to this receiver. The
receiver to be operated is switched by inputting the
preset code to set the remote control setting.
•Set the remote modes on the receivers before using
this function (see Remote Control Mode Setup on
page 96).
1 Check the operation selector switch to
MAIN
.
2Press .
3 Press and hold
REMOTE SETUP
, then release it after
the LED flashes twice.
4 Use the number buttons to enter the 5-digit preset
code (see below).
Receiver 1: 6 1 9 3 5 (Default)
Receiver 2: 6 2 6 3 0
Receiver 3: 6 2 6 3 1
Receiver 4: 6 2 6 3 2
The LED flashes twice when the preset code has been
properly registered. When the preset code is fully input,
the LED flashes once to indicate that the setting has
failed.
To operate another receiver, start over from step 1 to
input its preset code.
Setting the remote to control other
components
Most components can be assigned to one of the input
function buttons (such as DVD or CD) using the
component’s manufacturer preset code stored in the
remote.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
Note
•You can cancel or exit any of the steps by pressing
. To go back a step, press RETURN.
•After one minute of inactivity, the remote
automatically exits the operation.
Selecting preset codes directly
1 Press the input function button for the component
you want to control.
1
When assigning preset codes to TV CONTROL, press TV
CTRL here.
2 Press and hold
REMOTE SETUP
, then release it after
the LED flashes twice.
3 Use the number buttons to enter the 5-digit preset
code.
See Preset code list on page 113.
The LED flashes twice when the preset code has been
properly registered. When the preset code is fully input,
the LED flashes once to indicate that the setting has
failed.
4 Repeat steps 1 through 3 for the other components
you want to control.
To try out the remote control, switch the component on or
off (into standby) by pressing SOURCE. If it doesn’t
seem to work, select the next code from the list (if there
is one).
•Depending on the preset code, the signal may not be
transmitted when SOURCE is pressed. In this case,
try operating other buttons to see if the remote
control is working.
123
SLEEP
HDMI OUT
MCACCSIGNAL SEL
456
DIMMERA.ATTSBch
789
CLASSCH LEVELD.ACCESS
0
ENTER
INPUT
SELECT
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO
INFO
DISP
CH
RECEIVER
TV CTRL
RECEIVER
Note
1 You can’t assign , TUNER, iPod/USB, XM or SIRIUS.
RECEIVER
RECEIVER
VSX-9140TXH_CUXJ.book 73 ページ 2009年4月16日 木曜日 午前10時36分
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-9140TXH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-9140TXH in the language / languages: English as an attachment in your email.

The manual is 11,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info