574198
68
Zoom out
Zoom in
Previous page
1/88
Next page
Controlling the rest of your system
11
68
En
The remote controls should be 3 cm to 5 cm (1 to 2
inches) apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this receiver’s remote control.
For example, if you want to learn the playback control
signal, press and hold
briefly. The LCD display will
show
OK
if the operation has been learned.
1
If for some reasons the operation hasn’t been learned the
LCD will display
ERROR
briefly and then display
PRES
KEY
again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows
OK
.
2
Certain buttons represent operations that cannot be
learned from other remote controls.
3
The buttons
available are shown below (with the exception of the TV
controls, a combination of
SHIFT
and these buttons can
also be learned):
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold the RECEIVER button for a couple of
seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select
ERASE
then press
ENTER
.
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
3 Press the input source button corresponding to the
command to be erased then press
ENTER
.
The LCD display flashes
PRES KEY
.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows
OK
or
NO CODE
to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for a couple of
seconds when you’re done.
Resetting the remote control presets
This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select
RESET
then press
ENTER
.
RESET
flashes in the LCD display.
3 Press and hold
ENTER for about two seconds
.
The LCD shows
OK
to confirm the remote presets have
been erased.
Confirming preset codes
Use this feature to check which preset code is assigned
to an input source button.
1 While pressing the RECEIVER button, press
SETUP
.
The remote LCD display shows
SETUP
.
2 Use
/
to select READ ID then press
ENTER
.
The LCD on the remote prompts you for the input source
button you want to check.
Note
1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
2• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows
FULL
, it means the memory is full. See
Erasing one of the remote control button settings
below to erase a programmed button
you’re not using to free up more memory (note that some signals may take more memory than others).
3 Note that the number key decimal button (
+10
/
D.ACCESS
) may not be learned with some components.
3 cm to 5 cm
(1 to 2 inches)
SLEEP
+
10
SR
+
ANALOG
ATT
DISC
VIDEO
SEL
DIMMER
CLASS
D.ACCESS
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TV CONTROL
SHIFT
VOL
DVD SAT
VIDEO 1 TV CONT
DVR1
TUNE
TUNE
ST ST
STATUS
MCACC S.DIRECT
MULTI OPE
SIGNAL SEL
SBch
STEREO
MEMORY
TV CH
INPUT
SELECT
MPX
AUDIO SUBTITLE
ADV. SURR
STANDARD
ISOPHASE
THX
DTV INFO
MUTE
REC
TV VOL
i Pod
TUNER
RECEIVER
ENTER
REC STOP
HDD
CH
CH
DVD
AV PARAMETER
TOP MENU ì
DTV MENU
CH LEVEL
MENU
T.EDIT
BAND
GUIDE
RETURN
SETUP
CATEGORY
CD
DVR2
CD-R
TV VIDEO 2
XM RADIO
ROOM2/3
DISP
RECEIVER
ANALOG
AT T
MIDNIGHT/
LOUDNESS
DIMMER
SLEEP
SR+
+10
D.ACCESS
DIALOG E
S.RETRIEVER
CLASS
DISC
RECEIVER
SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TUNE
TUNE
ST ST
ENTER
TOP MENU
AV P AR AM ETER CH LEVEL
T. EDIT
MENU
RETURN
GUIDE
BAND
SETUP
TV DVR 1
TV CTRL
iPod
RECEIVER
TUNER
HDMI 1
DVD
ZONE 2HDMI 2 CD
CD-R/TAPE
DVR 2
XM RADIO
SIRIUS
TV CONTROL
SHIFT
VOL
STEREO/
F.S.SURR
PHOTO
STATUS
SIGNAL SEL
THX
ADV.SURR
SB ch
INPUT
SELECT
TV CH
MPX
AUDIO
DISP
SUBTITLE
MULTI OPE
STANDARD
PHASE
S.DIRECT
MCACC
RECANT INFO
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH
CH
DVD
RECEIVER
VSX-9120TXH_KU.book 68 ページ 2007年4月12日 木曜日 午前11時47分
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-9120TXH-k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-9120TXH-k in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-9120TXH-k

Pioneer VSX-9120TXH-k User Manual - English - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info