586462
101
Zoom out
Zoom in
Previous page
1/137
Next page
101
The MCACC PRO (VSX-1130)/Advanced MCACC (VSX-830) menu
12
Manual MCACC setup
You can use the settings in the Manual MCACC setup menu to make detailed adjustments when you’re more
familiar with the system. Before making these settings, you should have already completed Automatically con-
ducting optimum sound tuning (Full Auto MCACC) on page 58 .
You only need to make these settings once (unless you change the placement of your current speaker system or
add new speakers).
CAUTION
! The test tones used in the Manual MCACC setup are output at high volume.
Important
! Press the MCACC button while the pertinent setup screens are displayed to select MCACC presets.
! For some of the settings below, you’ll have to connect the setup microphone to the front panel and place it
about ear level at your normal listening position. Press HOME MENU to display the HOME MENU before you
connect the microphone to this receiver.
! See Problems when using the Auto MCACC Setup on page 59 for notes regarding high background noise
levels and other possible interference.
! If you’re using a subwoofer, switch it on and turn up the volume to the middle position.
1 Select ‘Manual MCACC’ from the MCACC PRO (VSX-1130)/Advanced MCACC (VSX-830)
menu, then press ENTER.
See Making receiver settings from the MCACC PRO (VSX-1130)/Advanced MCACC (VSX-830) menu on page 99
if you’re not already at this screen.
2 Select the setting you want to adjust.
If you’re doing this for the first time, you might want to make these settings in order.
! Fine Channel Level – Make fine adjustments to the overall balance of your speaker system (see Fine Channel
Level on page 101 ).
! Fine SP Distance – Make precise delay settings for your speaker system (see Fine Speaker Distance on page
101 ).
! Standing Wave – Control overly resonant low frequencies in your listening room (see Standing Wave on
page 102 ).
The last two settings are specifically for customizing the parameters explained in Acoustic Calibration EQ Adjust
on page 102 :
! EQ Adjust – Manually adjust the frequency balance of your speaker system while listening to test tones (see
Acoustic Calibration EQ Adjust on page 102 ).
! EQ Professional – Calibrate your system based on the direct sound coming from the speakers and make
detailed settings according to your room’s reverb characteristics (see Acoustic Calibration EQ Professional
on page 102 ).
Fine Channel Level
! Default setting: 0.0dB (all channels)
You can achieve better surround sound by properly adjusting the overall balance of your speaker system. You can
adjust the Channel Level of each speaker in 0.5 dB increments. The following setting can help you make detailed
adjustments that you may not achieve using the Manual speaker setup on page 106 .
1 Select ‘Fine Channel Level’ from the Manual MCACC setup menu.
The volume increases to the 0.0 dB reference level.
2 Adjust the level of the left channel.
This will be the reference speaker level, so you may want to keep the level around 0.0dB so that you’ll have plenty
of room to adjust the other speaker levels.
! After pressing ENTER, test tones will be output.
3 Select each channel in turn and adjust the levels (+/–12.0 dB) as necessary.
Use k/l to adjust the volume of the speaker you selected to match the reference speaker. When it sounds like
both tones are the same volume, press j to confirm and continue to the next channel.
! For comparison purposes, the reference speaker will change depending on which speaker you select.
! If you want to go back and adjust a channel, simply use i/j to select it.
4 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
Fine Speaker Distance
! Default setting: 10’00’’ (all speakers)
For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening position at the same time. You can adjust the distance of
each speaker in half inch increments. The following setting can help you make detailed adjustments that you may
not achieve using the Manual speaker setup on page 106 .
1 Select ‘Fine SP Distance’ from the Manual MCACC setup menu.
2 Adjust the distance of the left channel from the listening position.
VSX-1130 only: When setting the Dolby Enabled Speaker, input the vertical distance from the speaker to the ceil-
ing and the distance to each Dolby Enabled Speaker from the listening/viewing position. (page 25 ).
3 Select each channel in turn and adjust the distance as necessary.
Use k/l to adjust the delay of the speaker you selected to match the reference speaker. (VSX-1130 only: If Dolby
Enabled Speaker is used, the distance reached by the speaker sound reflected at the ceiling is displayed (page 25 ).)
Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of you and between your arm span.
! If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your
speakers very slightly.
! The subwoofer’s test tone differs in tone from other channels. Adjust so that the sound of the subwoofer can
be heard distinctly. Note that when adjusting the subwoofer, depending on the low frequency response of
your speaker, it may be difficult to hear the change even when the setting is increased or decreased or when
the position of the speaker is changed. Note that it may be difficult to compare this tone with the other speak-
ers in your setup (depending on the low frequency response of the reference speaker).
When it sounds like the delay settings are matched up, press j to confirm and continue to the next channel.
! For comparison purposes, the reference speaker will change depending on which speaker you select.
! If you want to go back and adjust a channel, simply use i/j to select it.
4 When you’re finished, press RETURN.
You will return to the Manual MCACC setup menu.
 
101


Need help? Post your question in this forum.

Forumrules
1

Forum

pioneer-vsx-830-k

Reset search

  • unable to get sound out of the rear speakers, can you help please Submitted on 9-4-2021 at 12:43

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-830 K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-830 K in the language / languages: English as an attachment in your email.

The manual is 20,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-830 K

Pioneer VSX-830 K User Manual - German - 146 pages

Pioneer VSX-830 K User Manual - Dutch - 146 pages

Pioneer VSX-830 K User Manual - French - 145 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info