Manual Pioneer VSX-830 K (page 94 of 137) (English)

586462

Zoom out

Zoom in

1/137

Controlling the rest of your system (VSX-1130 only)

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you

can program signals from the remote control of another component. This can also be used to program additional

operations (buttons not covered in the presets) after assigning a preset code.

The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer

format only).

Certain buttons represent operations that cannot be learned from other remote controls. The buttons available

are shown below:

STANDBY/ON

ENTER

SOURCE

INPUT

TV VOL

RECEIVER

ENTER

CLR

546

Fav

1 Press and hold RCU SETUP, then press ‘2’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To “learn” codes at the TV buttons, proceed to step 3.

! To cancel the preset setup mode press RCU SETUP.

2 Press the input function button for the component you want to control.

The LED blinks once and flashes continuously.

3 Point the two remote controls towards each other, then press the button that will be

doing the learning on this receiver’s remote control.

The LED flashes once, then stops flashing, remaining lit.

! The remote controls should be 3 cm (1 inch) apart.

3 cm

(1 inch)

This receiver’s

remote control

Other remote

control

4 Press the corresponding button on the other remote control that is sending (teaching) the

signal to this receiver’s remote control.

If the LED lights for one second and continues to flash, the setting has been successfully completed.

! If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one

input function on page 94 to erase a programmed button you’re not using to free up more memory (note

that some signals may take more memory than others).

! Note that interference from TVs or other devices will sometimes result in the remote control learning the

wrong signal.

! Some commands from other remote controls cannot be learned, but in most cases the remotes just need to

be moved closer together or farther apart.

5 To program additional signals for the current component repeat steps 3 and 4.

To program signals for another component, exit and repeat steps 2 through 4.

6 Press RCU SETUP to exit the programming mode.

Erasing one of the remote control button settings

This erases one of the buttons you have programmed and restores the button to the factory default.

1 Press and hold RCU SETUP, then press ‘8’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To erase operations registered at the TV buttons, proceed to step 3.

! To cancel the preset setup mode press RCU SETUP.

2 Press the input function button corresponding to the command to be erased.

The LED flashes once.

3 Press and hold the button to be erased for three seconds.

If the LED lights for one second, the erasing has been successfully completed.

4 Repeat step 3 to erase other buttons.

5 Press RCU SETUP to exit the erasing mode.

Erasing all learnt settings that are in one input function

This operation erases all the operational settings of other devices that have been programmed in one input func-

tion, and restores the factory default.

This function is handy for erasing all data programmed for devices no longer being used.

1 Press and hold RCU SETUP, then press ‘9’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To cancel the preset setup mode press RCU SETUP.

2 Press and hold the input function button corresponding to the command to be erased for

three seconds.

To erase the operations registered at all the TV buttons, press the TV INPUT button for 3 seconds.

If the LED lights for one second, the erasing has been successfully completed.

unable to get sound out of the rear speakers, can you help please Submitted on 9-4-2021 at 12:43
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-830 K in the language / languages: English as an attachment in your email.

The manual is 20,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-830 K

Pioneer VSX-830 K User Manual - German - 146 pages

Pioneer VSX-830 K User Manual - Dutch - 146 pages

Pioneer VSX-830 K User Manual - French - 145 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-830 K Manual

Product: