Manual Pioneer VSX-830 K (page 89 of 137) (English)

586462

Zoom out

Zoom in

1/137

Using other functions

In case of VSX-830

% Press SP-A/B.

Switches the speaker play on/off.

! You can perform the same operation by pressing SPEAKERS on the front panel.

Switching the HDMI output

VSX-1130 only

Set which terminal to use when outputting video and audio signals from the HDMI output terminals.

The HDMI OUT 1 terminal is compatible with the Control with HDMI function.

1 Press OUT P..

2 Use i/j to select ‘OUT 1/2’.

3 Use k/l to select the output settings for the HDMI OUT 1 and HDMI OUT 2 terminals.

Please wait a while when Please wait ... is displayed.

The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed.

! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-

nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV’s remote

control.

! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2 (page 110 ).

4 When you’re finished, press RETURN.

HDMI 4K/60p signal output setting

If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in accor-

dance with TV performance.

Operation is performed on the front panel of the unit. You cannot perform the setting if the multizone function is

not set to MULTI ZONE OFF (page 89 ).

1 Switch the receiver into standby.

2 While holding down ENTER on the front panel, press u STANDBY/ON.

The display shows RESET c NO d.

3 Select an input terminal that you wish to change settings using i/j.

! 4K/60pBD – Sets the signal for the BD IN terminal.

! 4K/60pH1 – Sets the signal for the HDMI IN 1 terminal.

! 4K/60pH2 – Sets the signal for the HDMI IN 2 terminal.

4 Use k/l to select the signal to set.

! 4:4:4 – Select this setting when connecting to a 4K/60p 4:4:4 24 bit compatible TV using HDMI. More high

quality video images can be enjoyed.

— When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video image may not

be output properly. In that case, select 4:2:0 to watch a 4K/60p 4:2:0 24 bit video image.

! 4:2:0 – Select this setting when connecting to a 4K/60p 4:2:0 24 bit compatible TV using HDMI.

5 When you’re finished, press RETURN.

6 Press u STANDBY/ON to switch on the receiver and your TV.

Make sure that the TV’s video input is set to this receiver.

Changing the channel level while listening

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor

when setting up a home theater system.

1 Press CH LV..

2 Use i/j to select the channel you wish to adjust.

3 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

4 When you’re finished, press RETURN.

Input Volume Absorber

This can be used to correct for the difference in volume between input sources.

1 Switch to the input whose volume you want to adjust.

2 Press CH LV..

3 Use i/j to select ‘ALL’.

4 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

5 When you’re finished, press RETURN.

Using the MULTI-ZONE controls

VSX-1130 only

The following steps use the front panel controls to adjust the sub zone volume and select sources. See HDZONE

remote controls on page 90 .

Important

! The settings must be changed at ZONE Setup in order to use the multi-zone function (page 110 ).

1 Press MULTI-ZONE ON/OFF on the front panel.

The zone switches between on and off each time the button is pressed.

The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON.

2 Press MULTI-ZONE CONTROL on the front panel.

Each press will switch between main zone and sub zone control.

! When the receiver is on, make sure that any operations for the sub zone are done while ZONE and your

selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone

only.

If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show

in the display.

3 Use the INPUT SELECTOR dial to select the source for the zone you have selected.

For example, HDZONE SAT/CBL sends the source connected to the SAT/CBL inputs to the primary (HDZONE)

sub room.

! If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets on

page 67 if you’re unsure how to do this). The tuner cannot be tuned to more than one station at a time.

Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not

to change stations when recording a radio broadcast.

unable to get sound out of the rear speakers, can you help please Submitted on 9-4-2021 at 12:43
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-830 K in the language / languages: English as an attachment in your email.

The manual is 20,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-830 K

Pioneer VSX-830 K User Manual - German - 146 pages

Pioneer VSX-830 K User Manual - Dutch - 146 pages

Pioneer VSX-830 K User Manual - French - 145 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-830 K Manual

Product: