794003
68
Zoom out
Zoom in
Previous page
1/76
Next page
Additional information12
68
En
HDMI
Considerable noise in radio
broadcasts. • Connect the antenna (page 19) and adjust the position for best reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and secure to a wall
(or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 19).
• Turn off equipment causing interference or move it away from the receiver (or
move antennas farther away from equipment causing noise).
Broadcast stations cannot be
selected automatically. • Connect an outdoor antenna (refer to page 19).
Noise during playback of a
cassette deck. • Move the cassette deck away from your receiver, until the noise disappears.
Sound is produced from other
components, but not from LD
or DVD player.
• Set the
SIGNAL SELECT
to
AUTO
,
DIGITAL
or
ANALOG
according to the type of
connections made (refer to page 36).
• Set the digital input settings correctly (refer to page 64).
Make digital connections (refer to page 12) and set the
SIGNAL SELECT
to
DIGITAL
(refer to page 36).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral position.
• Make sure the player’s settings are correct and/or the DTS signal out is on. Refer
to the instruction manual supplied with the DVD player.
• Set the input signal type to
DIGITAL
(see
Choosing the input signal
on page 36).
During a playback search,
noise is output from a DTS
compatible CD player.
• This is not a malfunction, but be sure to turn the volume down to prevent the
output of loud noise from your speakers.
Everything seems to be set up
correctly, but the playback
sound is odd.
• Check that the positive/negative speaker terminals on the receiver are matched
with the corresponding terminals on the speakers (see
Connecting the speakers
on
page 20).
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• See
Automatically setting up for surround sound (MCACC)
on page 8 to set up your
system again using MCACC (this will automatically compensate for a delay in the
subwoofer output).
After using the Auto MCACC
Setup, the speaker size setting
(
LARGE
or
SMALL
) is incorrect.
• Low-frequency noise could have been caused by an air conditioner or motor.
Switch off all appliances in the room and rerun the Auto MCACC Setup.
Can’t operate the remote
control. • Replace the batteries (refer to page 6).
• Operate within 7 m (23 ft.), 30° of the remote sensor (refer to page 29).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
VSX-918V model only:
Unplug anything connected to the
CONTROL IN
jack and
use remote normally (see
Operating other Pioneer components
on page 49).
VSX-918V model only:
The SR
cable is connected, but the
connected components can’t
be operated with the remote.
• Reinsert the SR cable, making sure it’s connected to the right jack (see
Using this
receiver with a Pioneer plasma display
on page 62).
• Make sure an analog connection has been made between the units.
• This feature only works with Pioneer products.
The display is dark or off. • Press
DIMMER
on the control repeatedly to return to the default.
Symptom Remedy
No picture or sound.
• If the problem still persists when connecting your HDMI component directly to
your monitor, please consult the component or monitor manual or contact the
manufacturer for support.
Problem Remedy
VSX_918_818_KU.book 68 ページ 2007年11月28日 水曜日 午後6時58分
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-818V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-818V in the language / languages: English as an attachment in your email.

The manual is 1.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info