574181
61
Zoom out
Zoom in
Previous page
1/68
Next page
AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-816
• Protect your new investment
The details of your purchase will be on file for reference in the event of an
insurance claim such as loss or theft.
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
• Receive free tips, updates and service bulletins on
your new product
Operating Instructions
Register your product at
www.pioneerelectronics.com (US)
www.pioneerelectronics.ca (Canada)
VSX_816.book.fm 1 ページ 2005年12月8日 木曜日 午後6時54分
WARNING TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
D1-4-2-1_En
IMPORTANT NOTICE THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND
KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.
D1-4-2-6-1_En
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_En
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
D36-P4_A_En
Wash hands after handling
For U.S. and Australia Model
C67-7-3_En
CAUTION – PREVENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD.
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE
FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
ATTENTION
POUR PREVENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER
CETTE FICHE POLARISEE AVEC UN
PROLONGATEUR UNE PRISE DE
COURANT OU UNE AUTRE SORTIE
DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE
A DECOUVVERT.
D2-4-4-1_EF
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
D8-10-1-3_EF
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate
the equipment.
D8-10-2_En
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and
televisions, use shielded cables and connectors for connections.
D8-10-3a_En
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
on vacation).
D3-4-2-2-1a_A_En
Thank you for buying this Pioneer product.
Please read through these operating instructions
so you will know how to operate your model
properly. After you have finished reading the
instructions, put them away in a safe place for future
reference.
Manufactured under license from Dolby
Laboratories. "Dolby", "Pro Logic",
"Surround EX", and the double-D symbol
are trademarks of Dolby Laboratories.
"DTS" ,"DTS-ES" ,"DTS 96/24" and
"Neo:6" are trademarks of Digital Theater
Systems, Inc.
VSX_816.book.fm 2 ページ 2005年12月8日 木曜日 午後6時54分
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead, within
an equilateral triangle, is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
D1-4-2-3_En
READ INSTRUCTIONS — All the safety and
operating instructions should be read before the
product is operated.
RETAIN INSTRUCTIONS — The safety and
operating instructions should be retained for
future reference.
HEED WARNINGS — All warnings on the product
and in the operating instructions should be
adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
CLEANING — The product should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides
or other volatile liquids since they may corrode
the cabinet.
ATTACHMENTS — Do not use attachments not
recommended by the product manufacturer as
they may cause hazards.
WATER AND MOISTURE — Do not use this
product near water — for example, near a
bathtub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming
pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product
and cart combination to overturn.
VENTILATION — Slots and openings in the cabinet
are provided for ventilation and to ensure
reliable operation of the product and to protect
it from overheating, and these openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
POWER SOURCES — This product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your product dealer or local power
company.
LOCATION – The appliance should be installed in a
stable location.
NONUSE PERIODS – The power cord of the
appliance should be unplugged from the outlet
when left un-used for a long period of time.
GROUNDING OR POLARIZATION
If this product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other), it will fit into the
outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
If this product is equipped with a three-wire
grounding type plug, a plug having a third
(grounding) pin, it will only fit into a grounding
type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding type plug.
POWER-CORD PROTECTION — Power-supply
cords should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
OUTDOOR ANTENNA GROUNDING — If an
outside antenna or cable system is connected to
the product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of
antenna-discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode. See Figure A.
LIGHTNING — For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
POWER LINES — An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can fall into such power
lines or circuits. When installing an outside
antenna system, extreme care should be taken
to keep from touching such power lines or
circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
OBJECT AND LIQUID ENTRY — Never push
objects of any kind into this product through
openings as they may touch dangerous voltage
points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the product.
SERVICING — Do not attempt to service this
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
DAMAGE REQUIRING SERVICE — Unplug this
product from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
When the power-supply cord or plug is
damaged.
If liquid has been spilled, or objects have fallen
into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
If the product has been dropped or damaged in
any way.
When the product exhibits a distinct change in
performance — this indicates a need for service.
REPLACEMENT PARTS — When replacement parts
are required, be sure the service technician has
used replacement parts specified by the
manufacturer or have the same characteristics
as the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
SAFETY CHECK — Upon completion of any service
or repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
WALL OR CEILING MOUNTING — The product
should not be mounted to a wall or ceiling.
HEAT — The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers)
that produce heat.
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRICAL CODE
Fig. A
D1-4-2-2_En
VSX_816.book.fm 3 ページ 2005年12月8日 木曜日 午後6時54分
Contents
01 Before you start
Checking what’s in the box
. . . . . . . . . . . . . . . 6
Loading the batteries
. . . . . . . . . . . . . . . . . . . 6
Installing the receiver
. . . . . . . . . . . . . . . . . . . 6
Ventilation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
02 5 minute guide
Introduction to home theater
. . . . . . . . . . . . . 7
Listening to Surround Sound
. . . . . . . . . . . . . 7
Using the Quick Setup
. . . . . . . . . . . . . . . . . . 8
03 Quick surround sound setup
Automatically setting up for surround sound
(MCACC)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Other problems when using the Auto
MCACC Setup
. . . . . . . . . . . . . . . . . . . . . . 11
04 Connecting up
Making cable connections
. . . . . . . . . . . . . . 12
Analog audio cables
. . . . . . . . . . . . . . . . . . 12
Digital audio cables
. . . . . . . . . . . . . . . . . . 12
Video cables
. . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting a DVD player and TV
. . . . . . . . . 13
Connecting the multichannel analog
outputs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting a satellite receiver or other
digital set-top box
. . . . . . . . . . . . . . . . . . . . . 14
Connecting other audio components
. . . . . . 15
About the WMA9 Pro decoder
. . . . . . . . . . 15
Connecting other video components
. . . . . . 16
Using the component video jacks
. . . . . . . . 17
Connecting to the front panel video
terminal
. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting antennas
. . . . . . . . . . . . . . . . . . 18
Using external antennas
. . . . . . . . . . . . . . . 18
Connecting the speakers
. . . . . . . . . . . . . . . 19
Hints on speaker placement
. . . . . . . . . . . . 20
AC outlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
05 Controls and displays
Front panel
. . . . . . . . . . . . . . . . . . . . . . . . . . 22
Display
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Remote control
. . . . . . . . . . . . . . . . . . . . . . . 25
Operating range of remote control
. . . . . . . 27
06 Listening to your system
Auto playback
. . . . . . . . . . . . . . . . . . . . . . . . 28
Listening in surround sound
. . . . . . . . . . . . . 28
Using the Advanced surround effects
. . . . . 29
Setting the effect options
. . . . . . . . . . . . . . 29
Listening in stereo
. . . . . . . . . . . . . . . . . . . . . 30
Listening with Acoustic Calibration EQ
. . . . . 30
Using surround back channel processing
. . . 31
Using Virtual Surround Back (VSB)
. . . . . . . 31
Using Midnight and Loudness
. . . . . . . . . . . . 32
Using the Sound Retriever
. . . . . . . . . . . . . . . 32
Enhancing dialog
. . . . . . . . . . . . . . . . . . . . . 32
Using the tone controls
. . . . . . . . . . . . . . . . . 32
Playing other sources
. . . . . . . . . . . . . . . . . . 33
Choosing the input signal
. . . . . . . . . . . . . . . 33
Selecting the multichannel analog inputs
. . . 33
07 The System Setup menu
Making receiver settings from the System
Setup menu
. . . . . . . . . . . . . . . . . . . . . . . . . . 34
Surround back speaker setting
. . . . . . . . . . . 34
Manual MCACC speaker setup
. . . . . . . . . . . 35
Fine Channel Level . . . . . . . . . . . . . . . . . . . 36
Fine Speaker Distance . . . . . . . . . . . . . . . . 36
Acoustic Calibration EQ . . . . . . . . . . . . . . . 37
Manual speaker setup . . . . . . . . . . . . . . . . . . 39
Speaker Setting . . . . . . . . . . . . . . . . . . . . . 40
Crossover Network . . . . . . . . . . . . . . . . . . . 41
Channel Level . . . . . . . . . . . . . . . . . . . . . . . 41
Speaker Distance . . . . . . . . . . . . . . . . . . . . 42
08 Using the tuner
Listening to the radio. . . . . . . . . . . . . . . . . . . 43
Improving FM stereo sound . . . . . . . . . . . . 43
Tuning directly to a station . . . . . . . . . . . . . 43
Saving station presets . . . . . . . . . . . . . . . . . . 43
Naming station presets. . . . . . . . . . . . . . . . 44
Listening to station presets. . . . . . . . . . . . . 44
09 Making recordings
Making an audio or a video recording . . . . . . 45
10 Controlling the rest of your
system
Operating other Pioneer components . . . . . . 46
Setting the remote to control other
components . . . . . . . . . . . . . . . . . . . . . . . . . 46
Selecting preset codes directly . . . . . . . . . . . 47
Erasing one of the remote control button
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Erasing all of the remote control presets . . . . 47
Direct function . . . . . . . . . . . . . . . . . . . . . . . 48
VSX_816.book.fm 4 ページ 2005年12月8日 木曜日 午後6時54分
English Italiano Français
Nederlands
EspañolDeutsch
Confirming preset codes
. . . . . . . . . . . . . . . . 48
Controls for TVs
. . . . . . . . . . . . . . . . . . . . . . . 49
Controls for other components
. . . . . . . . . . . 50
11 Other connections
Using XM Radio
. . . . . . . . . . . . . . . . . . . . . . 52
Connecting your XM Radio receiver
. . . . . . 52
Listening to XM Radio
. . . . . . . . . . . . . . . . . 53
Using XM Surround
. . . . . . . . . . . . . . . . . . 53
Saving channel presets
. . . . . . . . . . . . . . . . 53
Second Zone speaker B setup
. . . . . . . . . . . . 54
Switching the speaker system
. . . . . . . . . . 54
Bi-amping your front speakers
. . . . . . . . . . . 55
Bi-wiring your speakers
. . . . . . . . . . . . . . . . . 55
Connecting additional amplifiers
. . . . . . . . . . 56
Using this receiver with a Pioneer plasma
display
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Using the SR+ mode with a Pioneer
plasma display
. . . . . . . . . . . . . . . . . . . . . . 57
12 Other Settings
The Input Assign menu
. . . . . . . . . . . . . . . . . 58
The Other Setup menu
. . . . . . . . . . . . . . . . . . 59
Dynamic Range Control Setup
. . . . . . . . . . 59
Dual Mono Setup
. . . . . . . . . . . . . . . . . . . . 60
LFE Attenuator Setup
. . . . . . . . . . . . . . . . . 60
SR+ Setup for Pioneer plasma displays
. . . 60
13 Additional information
Troubleshooting
. . . . . . . . . . . . . . . . . . . . . . . 61
XM radio messages
. . . . . . . . . . . . . . . . . . . 63
Resetting the main unit
. . . . . . . . . . . . . . . . . 63
Switching the speaker impedance
. . . . . . . . . 63
Specifications
. . . . . . . . . . . . . . . . . . . . . . . . 64
Power cord caution
. . . . . . . . . . . . . . . . . . . . 65
Cleaning the unit
. . . . . . . . . . . . . . . . . . . . . . 65
VSX_816.book.fm 5 ページ 2005年12月8日 木曜日 午後6時54分
Before you start01
6
En
Chapter 1:
Before you start
Checking what’s in the box
Please check that you've received the following
supplied accessories:
Setup microphone
Remote control unit
Dry cell batteries (AA size IEC R6) x2
AM loop antenna
FM wire antenna
These operating instructions
Loading the batteries
Caution
Incorrect use of batteries may result in such
hazards as leakage and bursting. Observe the
following precautions:
Never use new and old batteries together.
Insert the plus and minus sides of the
batteries properly according to the marks
in the battery case.
Batteries with the same shape may have
different voltages. Do not use different
batteries together.
When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
Installing the
receiver
When installing this unit, make sure to put it on
a level and stable surface. Don’t install it on the
following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that
gives off a magnetic field). This may interfere
with the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other
movement
– in places that are very dusty
– in places that have hot fumes or oils (such as
a kitchen)
Ventilation
When installing this unit, make sure to leave
space around the unit for ventilation to
improve heat dispersal (at least 8 in. (20 cm) at
the top). If not enough space is provided
between the unit and walls or other equipment,
heat will build up inside, interfering with
performance and/or causing malfunctions.
Slot and openings in the cabinet are provided
for ventilation and to protect the equipment
from overheating. To prevent fire hazard, do not
place anything directly on top of the unit, make
sure the openings are never blocked or covered
with items (such as newspapers, table-cloths
and curtains), and do not operate the
equipment on thick carpet or a bed.
8 inches (20 cm)
Receiver
VSX_816.book.fm 6 ページ 2005年12月8日 木曜日 午後6時54分
5 minute guide
02
7
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 2:
5 minute guide
Introduction to home theater
Home theater refers to the use of multiple
audio tracks to create a surround sound effect,
making you feel like you're in the middle of the
action or concert. The surround sound you get
from a home theater system depends not only
on your speaker setup, but also on the source
and the sound settings of the receiver.
This receiver will automatically decode
multichannel Dolby Digital, DTS, or Dolby
Surround sources according to your speaker
setup. In most cases, you won’t have to make
changes for realistic surround sound, but
other possibilities (like listening to a CD with
multichannel surround sound) are explained in
Listening to your system
on page 28.
Listening to Surround Sound
With the following quick setup guide, you
should have your system hooked up for
surround sound in no time at all. In most
cases, you can simply leave the receiver in the
default settings.
Be sure to complete all connections before
connecting to an AC power source.
1 Connect your DVD player and TV.
See
Connecting a DVD player and TV
on page 13
to do this. For surround sound, you’ll want to
hook up using a digital connection from the
DVD player to the receiver.
2 Connect your speakers and place them for
optimal surround sound.
See
Connecting the speakers
on page 19.
Where you place the speakers will have a big
effect on the sound. Place your speakers as
shown below for the best surround sound
effect. Also see
Hints on speaker placement
on
page 20 for more on this.
3 Plug in and switch on the receiver, followed
by your DVD player, subwoofer and TV.
Make sure you’ve set the video input on your TV
to this receiver. Check the manual that came
with the TV if you don’t know how to do this.
4 Press QUICK SETUP on the front panel to
specify your speaker setup, room size and
listening position.
Use the
MULTI JOG
dial to select and
ENTER
to confirm your selection. See
Using the Quick
Setup
below for more on this.
5 Play a DVD, and adjust the volume.
Make sure that
DVD
is showing in the
receiver’s display. If it isn’t, press
DVD
on the
remote to set the receiver to the DVD input.
1
There are several other sound options you can
select. See
Listening to your system
on page 28
for more on this.
2
Note
1 You may need to set your DVD player to output Dolby Digital, DTS and 88.2/96kHz PCM (2 channel) audio (see your DVD play-
er’s manual for more on this).
2 Depending on your DVD player or source disc, you may only get 2 channel sound. In this case, the listening mode must be set
to
STANDARD
(see
Listening in surround sound
on page 28 if you need to do this) if you want multichannel surround sound.
Front
speaker
(L)
Surround
speaker (LS)
Surround
speaker (RS)
Surround back
speaker (SBL)
Surround
back
speaker (SBR)
Center
speaker
(C)
Subwoofer (SW)
Listening
position
Front
speaker
(R)
VSX_816.book.fm 7 ページ 2005年12月8日 木曜日 午後6時54分
5 minute guide02
8
En
Using the Quick Setup
You can use the Quick Setup to get your
system up and running with just a few button
presses. The receiver automatically makes the
necessary settings after you have selected your
speaker setup, room size and listening
position. Use the front panel controls for the
steps below.
If you want a more complete setup option,
refer to
Automatically setting up for
surround sound (MCACC)
on page 9. If you
choose to do so, you can skip the Quick
Setup.
1
1 If the receiver is off, press
STANDBY/ON
to turn the power on.
2 Press
QUICK SETUP
.
SW DET
flashes in the display while the
receiver checks your setup for a subwoofer.
SW YES
or
SW NO
confirms the subwoofer
check, then the display prompts you to
select your speaker setup.
3 Use the
MULTI JOG
dial to choose your
speaker setup.
When a subwoofer was detected in step 2, the
following choices are available:
2.1ch – 3.1ch – 4.1ch – 5.1ch – 6.1ch – 7.1ch
If a subwoofer wasn’t detected in step 2, you
can cycle between the following choices:
2.0ch – 3.0ch – 4.0ch – 5.0ch – 6.0ch – 7.0ch
Check the table below to find the speaker
setup that corresponds with your system.
4 Press
ENTER
.
5 Use the
MULTI JOG
dial to choose your
room size.
Depending on the distance of your speakers
from the listening position, choose between
small, medium, or large (
S
,
M
or
L
),
M
being an
average-sized room.
6 Press
ENTER
.
7 Use the
MULTI JOG
dial to choose your
listening position.
You can cycle between the following choices:
FWD
– If you are nearer to the front
speakers than the surround speakers
MID
– If you are equal distance from the
front and surround speakers
BACK
– If you are nearer to the surround
speakers than the front speakers
8 Press
ENTER
to confirm your setup.
The display shows the speaker setup, room size
and listening position that you have selected.
Note
1 See also
Making receiver settings from the System Setup menu
on page 34 for more setup options.
STANDBY/ON
PHONES
DVD/ LD
TV/SAT DVR/ VCR
STANDARD
MIDNIGHT/
LOUDNESS
ADVANCED
SURR
ST/DIRECT/
AUTO SURR
LISTENING
MODE
QUICK
SETUP
SETUP
TUNING/
STATION
TONE
ANALOG
ATT
SPEAKERS
TUNER
EDIT
DIMMER
MULTI JOG
DIGITAL PRECISION
PROCESSING
UPDOWN
MULTI JOG
MASTER
VOLUME
ENTER
AUDIO / VI DEO MULTI- CHANNEL
RECEIVER
VSX
-
816
MCACC
SETUP MIC
AUX
SIGNAL
SELECT
SB
ch
PROCESSING
ACOUSTIC
EQ
DIGITAL PRECISION
PROCESSING
VSX_816.book.fm 8 ページ 2005年12月8日 木曜日 午後6時54分
Quick surround sound setup
03
9
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 3:
Quick surround sound setup
Automatically setting up for
surround sound (MCACC)
The Auto Multi-Channel Acoustic Calibration
(MCACC) setup measures the acoustic
characteristics of your listening area, taking
into account ambient noise, speaker size and
distance, and tests for both channel delay and
channel level. After you have set up the
microphone provided with your system, the
receiver uses the information from a series of
test tones to optimize the speaker settings and
equalization for your particular room.
Important
The Auto MCACC Setup will overwrite any
existing speaker settings you’ve made.
Make sure the headphones are unplugged.
Caution
The test tones used in the Auto MCACC
Setup are output at high volume.
1 Switch on the receiver and your TV.
2 Connect the microphone to the MCACC
SETUP MIC
jack on the front panel.
Make sure there are no obstacles between the
speakers and the microphone.
If you have a tripod, use it to place the
microphone so that it’s about ear level at your
normal listening position. Otherwise, place the
microphone at ear level using a table or a chair.
3 Press
RECEIVER
on the remote control,
then press the
SETUP
button.
An on-screen display (OSD) appears on your
TV. Use
///
and
ENTER
on the remote
control to navigate through the screens and
select menu items. Press
RETURN
to exit the
current menu.
Press
SETUP
at any time to exit the System
Setup menu.
1
4 Select ‘Auto MCACC’ from the System
Setup menu then press ENTER.
5 Make sure ‘Normal (SB)’ is selected then
press ENTER.
2
Try to be as quiet as possible after pressing
ENTER
. The system outputs a series of test
tones to establish the ambient noise level.
RECEIVER
SOURCE
INPUT
SELECT
TV DVR
TV CTRL
CD
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
+10
D.ACCESS
CLASS
DISC
ENTER
TV CONTROL
VOL
TUNE
TUNE
ST ST
INPUT
SELECT
TV CH
REC
TV VOL
ENTER
TOP MENU
DTV MENU
O/O O
T. EDIT
MENU
RETURN
GUIDE
SETUP
CATEGORY
Note
1 The screensaver automatically starts after three minutes of inactivity. If you cancel the Auto MCACC Setup at any time, the
receiver automatically exits and no settings will be made.
2 If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through
Surround back speaker setting
on page 34 and make sure to connect your speakers as necessary before continuing.
UPDOWN
MASTER
VOLUM E
MCACC
SETUP MIC
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
2. Auto MCACC
Surr Back System
Normal (SB) ]
: Cancel ENTER : Start
VSX_816.book.fm 9 ページ 2005年12月8日 木曜日 午後6時54分
Quick surround sound setup03
10
En
6 Follow the instructions on-screen.
Make sure the microphone is connected.
If you’re using a subwoofer, it is
automatically detected every time you
switch on the system. Make sure it is on
and the volume is turned up.
See below for notes regarding background
noise and other possible interference.
7 Wait for the test tones to finish.
A progress report is displayed on-screen while
the receiver outputs test tones to determine
the speakers present in your setup. Try to be as
quiet as possible while it’s doing this.
For correct speaker settings, do not adjust
the volume during the test tones.
8 Confirm the speaker configuration.
The configuration shown on-screen should
reflect the actual speakers you have.
If the speaker configuration displayed isn’t
correct, use
/
to select the speaker and
/
to change the setting (and number for
surround back). When you’re finished, go to
the next step.
If you see an error message (
ERR
) in the right
side column, there may be a problem with the
speaker connection. If selecting
RETRY
doesn’t fix the problem, turn off the power and
check the speaker connections.
9 Make sure ‘OK’ is selected, then press
ENTER.
A progress report is displayed on-screen while
the receiver outputs more test tones to
determine the optimum receiver settings for
channel level, speaker distance, and Acoustic
Calibration EQ.
Again, try to be as quiet as possible while this
is happening. It may take 3–8 minutes.
10 The Auto MCACC Setup has finished!
Select ‘SKIP’ to go back to the System Setup
menu.
The MCACC indicator on the front panel will
light to show the setup is complete.
The settings made in the Auto MCACC Setup
should give you excellent surround sound from
your system, but it is also possible to adjust
these settings manually using the System
Setup menu (starting on page 34).
1
You can also choose to view the settings by
selecting individual parameters from the
Analyzed Data Check
screen:
Speaker Setting
– The size and number of
speakers you’ve connected (see page 40
for more on this)
Speaker Distance
– The distance of your
speakers from the listening position (see
page 42 for more on this)
2.Auto MCACC
Now Analyzing
Environment Check
Ambient Noise [ OK ]
Microphone [ ]
Speaker YES/NO [ ]
:Cancel
OK
OK
2.Auto MCACC
CHECK!
Front [ YES ]
Center [ YES ]
Surround [ YES ]
SB [ Yx2 ]
SUB W. [ YES ]
OK
:Cancel
Note
1• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 5 inches (12cm)
will end up with different size settings. You can correct the setting manually using the
Speaker Setting
on page 40.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be
accurate (taking delay and room characteristics into account) and generally does not need to be changed.
2.Auto MCACC
Now Analyzing
Surround Analyzing
Speaker System [ ]
Speaker Distance [ ]
Channel Level [ ]
Acoustic Cal EQ [ ]
:Cancel
VSX_816.book.fm 10 ページ 2005年12月8日 木曜日 午後6時54分
Quick surround sound setup
03
11
En
English
Français
Deutsch
Nederlands
Italiano
Español
Channel Level
– The overall balance of
your speaker system (see page 41 for more
on this)
Acoustic Cal EQ
– Adjustments to the
frequency balance of your speaker system
based on the acoustic characteristics of
your room (see page 37 for more on this)
Press
RETURN
after you have finished
checking each screen. When you’re finished,
select
SKIP
to go back to the System Setup
menu.
Other problems when using the Auto
MCACC Setup
If the room environment is not optimal for the
Auto MCACC Setup (too much background
noise, echo off the walls, obstacles blocking
the speakers from the microphone) the final
settings may be incorrect. Check for household
appliances (air conditioner, fridge, fan, etc.),
that may be affecting the environment and
switch them off if necessary. If there are any
instructions showing in the front panel display,
please follow them.
Some older TVs may interfere with the
operation of the microphone. If this seems
to be happening, switch off the TV when
doing the Auto MCACC Setup.
VSX_816.book.fm 11 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up04
12
En
Chapter 4:
Connecting up
Making cable connections
Important
Before making or changing connections,
switch off the power and disconnect the
power cord from the AC outlet.
Make sure not to bend the cables over the
top of this unit. If this happens, the
magnetic field produced by the
transformers in this unit may cause a
humming noise from the speakers.
Before unplugging the power cord, switch
the power into standby.
Analog audio cables
Use stereo RCA phono cables to connect
analog audio components. These cables are
typically red and white, and you should
connect the red plugs to R (right) terminals
and white plugs to L (left) terminals.
Digital audio cables
Commercially available coaxial digital audio
cables or optical cables should be used to
connect digital components to this receiver.
1
Video cables
Standard RCA video cables
These cables are the most common type of
video connection and are used to connect to
the composite video terminals. The yellow
plugs distinguish them from cables for audio.
S-video cables
S-video cables give you a clearer picture
reproduction than standard RCA video cables
by sending separate signals for the luminance
and color.
Component video cables
Use component video cables to get the best
possible color reproduction of your video
source. The color signal of the TV is divided into
the luminance (
Y
) signal and the color (
P
B
and
P
R
) signals and then output. In this way,
interference between the signals is avoided.
Note
1• When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket.
• When storing optical cable, coil loosely. The cable may be damaged if bent around sharp corners.
• You can also use a standard RCA video cable for coaxial digital connections.
Right (red)
Analog audio cables
Left (white)
Coaxial digital audio cable Optical cable
S
tandard RCA video cable
S Video
Green (Y)
Blue (P
B)
Red (P
R)
Component video cables
VSX_816.book.fm 12 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up
04
13
En
English
Français
Deutsch
Nederlands
Italiano
Español
Connecting a DVD player and TV
This page shows you how to connect your DVD
player and TV to the receiver.
1 Connect a coaxial digital audio output on
your DVD player to the DIGITAL COAX 1
(DVD/LD) input on this receiver.
Use a coaxial digital audio cable for the
connection.
1
2 Connect the composite video output and
the stereo analog audio outputs
2
on your
DVD player to the DVD/LD inputs on this
receiver.
Use a standard RCA video cable
3
and a stereo
RCA phono cable for the connection.
If your DVD player has multichannel
analog outputs, see
Connecting the
multichannel analog outputs
below for how
to connect it.
3 Connect the analog audio outputs from
your TV to the TV/SAT inputs on this receiver.
This will allow you to play the sound from the
TV's built-in tuner. Use a stereo RCA phono
cable to do this.
If your TV has a built-in digital decoder, you
can also connect an optical digital audio
output from your TV to the
DIGITAL OPT 2
(TV/SAT)
input on this receiver. Use an
optical cable for the connection.
4 Connect the MONITOR OUT video jack on
this receiver to a video input on your TV.
Use a standard RCA video cable to connect to
the composite video jack.
4
Note
1 If your DVD player only has an optical digital output, you can connect it to the optical input on this receiver using an optical
cable. When you set up the receiver you'll need to tell the receiver which input you connected the player to (see
The Input Assign
menu
on page 58).
2 This connection will allow you to make analog recordings from your DVD player.
3 For better quality, you can also connect with S-video using the
S-VIDEO
DVD/LD
jack. If your player also has a component
video output, you can connect this too. See
Using the component video jacks
on page 17 for more on this.
4 For better quality, you can also connect with S-video using the
S-VIDEO MONITOR OUT
jack. See
Using the component video
jacks
on page 17 if you want to use the component video outputs to connect this receiver to your TV.
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/VCR
)
COAX
(
DVD/LD
)
1
2
ASSIGNABLE
DIGITAL IN
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
REC
CD-R
/TAPE
/MD
FRONT
PREOUT
ANTENNA
CONTROL
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
This receiver
TV
ANALOG AUDIO OUT
LR
DIGITAL
AUDIO OUT
OPTICAL
VIDEO IN
DVD player
AUDIORL
DIGITAL OUT
ANALOG OUT
COAXIAL
VIDEO OUT
1
2
4
3
VSX_816.book.fm 13 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up04
14
En
Connecting the multichannel analog
outputs
For DVD Audio and SACD playback, your DVD
player may have 5.1 channel analog outputs.In
this case, you can connect the multichannel
analog outputs to the multichannel inputs of
this receiver as shown below.
1
Connecting a satellite receiver
or other digital set-top box
Satellite and cable receivers, and terrestrial
digital TV tuners are all examples of so-called
`set-top boxes'.
1 Connect a set of audio/video outputs on
the set-top box component to the TV/SAT
AUDIO and VIDEO inputs on this receiver.
2
Use a stereo RCA phono cable for the audio
connection and a standard RCA video cable for
the video connection.
3
2 Connect an optical digital audio output
from your set-top box component to the
DIGITAL OPT 2 (TV/SAT) input on this receiver.
Use an optical cable for the connection.
4
Note
1 The multichannel input can only be used when
DVD 5.1 ch
is selected (see page 33).
MONITO
Y
P
COMPONE
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/ V
FRONT
RL
S
P
E
A
K
E
R
S
(
DVR/ VCR
)
COAX
(
DVD/ LD
)
1
2
ASSIGNABLE
DIGITAL IN
R
A
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
SUB
WOOFER
SURROUND
CEN-
TER
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
L
R
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
DVD 5.1CH INPUT
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
CENTER
OUTPUT
SUB
WOOFER
OUTPUT
VIDEO
OUTPUT
SURROUND
OUTPUT
FRONT
OUTPUT
RL RL
This receiver
DVD/multi-channel decoder
with multi-channel analog
output jacks
2 If you've already connected your TV to the
TV/SAT
inputs, simply choose another input. However, to receive a signal, you'll
need to press the input select button for the input you connected the set-top box to.
3 For better quality, you can also connect with S-video using the
S-VIDEO
TV/SAT
jack. If your set-top box also has a component
video output, you can connect this too. See
Using the component video jacks
on page 17 for more on this.
4 If your satellite/cable receiver doesn’t have a digital audio output, omit this step. If it only has a coaxial digital output, you can
connect it to one of the coaxial inputs on this receiver using a coaxial digital audio cable. When you set up the receiver you'll
need to tell the receiver which input you connected the set-top box to (see
The Input Assign menu
on page 58).
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/VCR
)
COAX
(
DVD/LD
)
1
2
ASSIGNABLE
DIGITAL IN
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
DIGITAL OUT
AV OUT
VIDEOAUDIOR
L
2 1
OPTICAL COAXIAL
STB
This receiver
VSX_816.book.fm 14 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up
04
15
En
English
Français
Deutsch
Nederlands
Italiano
Español
Connecting other audio
components
The number and kind of connections depends
on the kind of component you’re connecting.
1
Follow the steps below to connect a CD-R, MD,
DAT, tape recorder or other audio component.
1 If your component has a digital output,
connect this to a digital input on the receiver
as shown.
The example shows a coaxial connection to the
CD
digital input jack using a coaxial digital
audio cable.
2 If necessary, connect the analog audio
outputs of the component to a set of spare
audio inputs on this receiver.
You’ll need to make this connection for
components without a digital output, or if you
want to record from a digital component. Use a
stereo RCA phono cable as shown.
3 If you're connecting a recorder, connect
the analog audio outputs (REC) to the analog
audio inputs on the recorder.
The example shows an analog connection to
the
CD-R/TAPE/MD
analog output jack using
a stereo RCA phono cable.
About the WMA9 Pro decoder
This unit has an on-board Windows Media
®
Audio 9 Professional (WMA9 Pro) decoder, so
it is possible to playback WMA9 Pro-encoded
audio using a coaxial or optical digital
connection when connected to a WMA9 Pro-
compatible player.
Note
1 Note that you must connect digital components to analog audio jacks if you want to record to/from digital components (like
an MD) to/from analog components.
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/VCR
)
COAX
(
DVD/LD
)
1
2
ASSIGNABLE
DIGITAL IN
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
CD-R, MD, DAT, Tape recorder, etc.
DIGITAL OUT
OPTICAL COAXIAL
AUDIO IN
R
L
IN
REC
AUDIO OUT
R
L
PLAY
OUT
1
3 2
This receiver
VSX_816.book.fm 15 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up04
16
En
However, the connected DVD player, set-top
box, etc. must be able to output WMA9 Pro
format audio signals through a coaxial or
optical digital output.
Microsoft, Windows Media
®
, and the Windows logo are
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Connecting other video
components
This receiver has audio/video inputs and
outputs suitable for connecting analog or
digital video recorders, including VCRs, DVD-
recorders and HDD recorders.
1 Connect a set of audio/video outputs on
the recorder to the DVR/VCR AUDIO and
VIDEO inputs on this receiver.
Use a stereo RCA phono cable for the audio
connection and a standard RCA video cable for
the video connection.
1
2 Connect a set of audio/video inputs on
the recorder to the DVR/VCR AUDIO and
VIDEO outputs on this receiver.
Use a stereo RCA phono cable for the audio
connection and a standard RCA video cable for
the video connection.
2
3 Connect a coaxial digital audio output on
your video component to the DIGITAL COAX 2
(DVR/VCR) input on this receiver.
Use a coaxial digital audio cable for the
connection.
3
Note
1 For better quality, you can also connect with S-video using the
S-VIDEO
DVR/VCR IN
jack. If your video component also has
a component video output, you can connect this too. See
Using the component video jacks
on page 17 for more on this.
2 For better quality, you can also connect with S-video using the
S-VIDEO
DVR/VCR OUT
jack.
3 If your video component only has an optical digital output, you can connect it to the optical input on this receiver using an
optical cable. When you set up the receiver you'll need to tell the receiver which input you connected the player to (see
The Input
Assign menu
on page 58).
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/VCR
)
COAX
(
DVD/LD
)
1
2
ASSIGNABLE
DIGITAL IN
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
VCR, DVR, LD player, etc.
DIGITAL OUT
OPTICAL COAXIAL
VIDEO IN
R L
AUDIO IN
IN
REC
AUDIO OUT
VIDEO OUT
R L
PLAY
OUT
3
1 2
This receiver
VSX_816.book.fm 16 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up
04
17
En
English
Français
Deutsch
Nederlands
Italiano
Español
Using the component video jacks
Component video should deliver superior
picture quality when compared to composite
video. A further advantage (if your source and
TV are both compatible) is progressive-scan
video, which delivers a very stable, flicker-free
picture. See the manuals that came with your
TV and source component to check whether
they are compatible with progressive-scan
video.
Important
If you connect any source component to
the receiver using a component video
input, you must also have your TV
connected to this receiver's
COMPONENT
VIDEO MONITOR OUT
jacks.
1 Connect the component video outputs of
your source to a set of component video
inputs on this receiver.
Use a three-way component video cable for the
connection.
2 If necessary, assign the component video
inputs to the input source you've connected.
This only needs to be done if you didn’t connect
according to the following defaults:
COMP 1
DVD
COMP 2
TV
COMP 3
DVR
See
Assigning the component video inputs
on
page 58 for more on this.
3 Connect the COMPONENT VIDEO
MONITOR OUT jacks on this receiver to the
component video inputs on your TV or
monitor.
Use a three-way component video cable.
Connecting to the front panel video
terminal
Front video connections are accessed via the
front panel using the
VIDEO
button. There are
standard audio/video jacks as well as an S-
video jack and an optical input. Hook them up
the same way you made the rear panel
connections.
CD
CD
-
R/TAPE/MD FM AM
XM
MCACC
SETUP MIC
DIGITAL INAUDIO RLVIDEO
VIDEO
INPUT
S
-
VIDEO
AUX
DIGITAL PRECISION
PROCESSING
This receiver
LV
R
VIDEO OUTPUT
DIGITAL OUT
Video
camera
(etc.)
VSX_816.book.fm 17 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up04
18
En
Connecting antennas
Connect the AM loop antenna and the FM wire
antenna as shown below. To improve reception
and sound quality, connect external antennas
(see
Using external antennas
below).
1 Pull off the protective shields of both AM
antenna wires.
2 Push open the tabs, then insert one wire
fully into each terminal, then release the tabs
to secure the AM antenna wires.
3 Fix the AM loop antenna to the attached
stand.
To fix the stand to the antenna, bend in the
direction indicated by the arrow (
fig. a
) then
clip the loop onto the stand (
fig. b
).
If you plan to mount the AM antenna to a
wall or other surface, secure the stand with
screws (
fig. c
) before clipping the loop to
the stand. Make sure the reception is clear.
4 Place the AM antenna on a flat surface
and in a direction giving the best reception.
5 Connect the FM wire antenna in the same
way as the AM loop antenna.
For best results, extend the FM antenna fully
and fix to a wall or door frame. Don’t drape
loosely or leave coiled up.
Using external antennas
To improve FM reception
Use an F connector to connect an external FM
antenna.
To improve AM reception
Connect a 15–18 foot length of vinyl-coated
wire to the AM antenna terminal without
disconnecting the supplied AM loop antenna.
For the best possible reception, suspend
horizontally outdoors.
AM
LOOP
FM UNBAL
75
ANTENNA
3
1
2
4
5
fig. a fig. b fig. c
AM
LOOP
FM UNBAL
75
ANTENNA
F connector
AM
LOOP
FM UNBAL
75
ANTENNA
Outdoor
antenna
Indoor antenna
(vinyl-coated wire)
15–18 ft. (5–6m)
VSX_816.book.fm 18 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up
04
19
En
English
Français
Deutsch
Nederlands
Italiano
Español
Connecting the speakers
A complete setup of eight speakers (including the subwoofer) is shown here but everyone’s home
setup will vary. Simply connect the speakers you have in the manner shown below.
1
The receiver
will work with just two stereo speakers (the front speakers in the diagram) but using at least three
speakers is recommended, and a complete setup is best.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left
to the left terminal. Also make sure the positive and negative (
+
/
) terminals on the receiver match
those on the speakers.
2
You can use speakers with a nominal impedance between 6–16
(please
see
Switching the speaker impedance
on page 63 if you plan to use speakers with an impedance of
less than 8
).
Caution
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker
terminal. Use good quality speaker wire to connect the speakers to the receiver.
Note
1 If you’re not using a subwoofer, change the front speaker setting (see
Speaker Setting
on page 40) to large.
2 If you are using only one surround back speaker, connect it to the surround back left (
L
) terminal.
ASSIGNABLE
MONITOR OUT
Y
P
B
COMPONENT VIDEO
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVD/ LD
)
(
DVR/ VCR
)
IN
IN
FRONT
RL
CENTERSURROUND
S
P
E
A
K
E
R
S
(
DVR/VCR
)
COAX
(
DVD/ LD
)
1
2
ASSIGNABLE
DIGITAL IN
PR
Y
P
B
PR
(
TV/SAT
)
IN
FRONT SURROUND SURROUND
BACK
1
2
R
L
SURROUND BACK
A B
L
L
RRR
CENTER
LL
R
(
TV/ SAT
)
3
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
SUB
WOOFER
SURROUND
CEN-
TER
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
L
R
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
PREOUT
DVD 5.1CH INPUT
AC OUTLET
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
INPUT
Front speakers
LR C LSRS
Powered
subwoofer
This receiver
SW
Surround back speakers
SBL SBR
Surround speakers
Center speaker
VSX_816.book.fm 19 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up04
20
En
Make sure that the speaker cable you’re using
is properly prepared with about
3
/
8
in. (10 mm)
of insulator stripped from each wire, with the
exposed wire strands twisted together (
fig. A
).
Unscrew the terminal a few turns until there is
enough space to insert the exposed wire
(
fig. B
). Once the wire is in position, tighten the
terminal until the wire is firmly clamped (
fig. C
).
The speaker terminals also accept single
banana plugs. (Refer to speaker manual for
details.)
Caution
These speaker terminals are hazardous
when live. To prevent the risk of electric
shock when connecting or disconnecting
the speaker cables, disconnect the power
cord.
Hints on speaker placement
Speakers are usually designed with a
particular placement in mind. Some are
designed to be floorstanding, while others
should be placed on stands to sound their best.
Some should be placed near a wall; others
should be placed away from walls. We have
provided a few tips on getting the best sound
from your speakers (following), but you should
also follow the guidelines on placement that
the speaker manufacturer provided with your
particular speakers to get the most out of
them.
Place the front left and right speakers at
equal distances from the TV.
When placing speakers near the TV, we
recommend using magnetically shielded
speakers to prevent possible interference,
such as discoloration of the picture when
the TV is switched on. If you do not have
magnetically shielded speakers and notice
discoloration of the TV picture, move the
speakers farther away from the TV.
If you're using a center speaker, place the
front speakers at a wider angle. If not, place
them at a narrower angle.
Place the center speaker above or below
the TV so that the sound of the center
channel is localized at the TV screen. Also,
make sure the center speaker does not
cross the line formed by the leading edge
of the front left and right speakers.
It is best to angle the speakers towards the
listening position. The angle depends on
the size of the room. Use less of an angle
for bigger rooms.
Surround and surround back speakers
should be positioned a foot-and-a-half to
three feet (60 cm–90 cm) higher than your
ears and titled slightly downward. Make
sure the speakers don't face each other.
To achieve the best possible surround
sound, install your speakers as shown
below. Be sure all speakers are installed
securely to prevent accidents and improve
sound quality.
Caution
If you choose to install the center speaker
on top of the TV, be sure to secure it with
putty, or by other suitable means, to reduce
the risk of damage or injury resulting from
the speaker falling from the TV in the event
of external shocks such as earthquakes.
Make sure no exposed speaker wire is
touching the rear panel, this may cause the
receiver to turn off automatically.
10mm
fig. A fig. B fig. C
VSX_816.book.fm 20 ページ 2005年12月8日 木曜日 午後6時54分
Connecting up
04
21
En
English
Français
Deutsch
Nederlands
Italiano
Español
Overhead view of speaker setup
You can also refer to the 3-D speaker setup
illustration on page 7.
.
The diagrams below show suggested surround
and surround back speaker orientation. The
first diagram (
fig. A
) shows orientation with one
surround back speaker (or none) connected.
The second (
fig. B
) shows orientation with two
surround back speakers connected.
3-D view of
7.1 channel
speaker setup
AC outlet
Power supplied through this outlet is turned on
and off by the receiver's power switch. Total
electrical power consumption of connected
equipment should not exceed 100 W (0.8 A).
This unit should be disconnected by
removing the power plug from the wall
socket when not in regular use (ex. when
on vacation).
Caution
Do not connect a TV set
, monitor, heater, or
similar appliance to this unit's AC outlet.
Do not connect appliances with high
power consumption to the AC outlet in
order to avoid overheating and fire risk.
This can also cause the receiver to
malfunction.
Since a subwoofer or power amplifier can
exceed the 100W maximum when playing
sources at a high volume, this type of
equipment should not be connected to the
AC outlet.
Surround
left
Surround
right
Listening position
Front
left
Front
rightCenter
Subwoofer
Surround back Surround back
Single surround back speaker
left right
90~120
fig. A fig. B
LS
LS
RS
RS
SB
LS
RS
0~60
SBL
SBL
SBR
SBR
AC OUTLET
VSX_816.book.fm 21 ページ 2005年12月8日 木曜日 午後6時54分
Controls and displays05
22
En
Chapter 5:
Controls and displays
Front panel
1 Input select buttons
Press to select an input source.
2 Digital Precision Processing indicator
Lights to indicate digital processing.
3 Character display
See
Display
on page 23.
4 MCACC indicator
Lights when Acoustic Calibration EQ (page 30)
is on (Acoustic Calibration EQ is automatically
set to
ALL CH ADJUST
after the Auto MCACC
Setup (page 9) or EQ Auto Setup (page 37)).
5
ENTER
6
MULTI JOG
dial
Use the
MULTI JOG
dial to select various
settings and menu options.
7
LISTENING MODE
buttons
STANDARD
– Press for Standard decoding
and to switch between the various Pro
Logic IIx and Neo:6 options (page 28).
ADVANCED SURR
– Use to switch
between the surround modes (page 29).
ST/DIRECT/AUTO SURR
Selects stereo/direct playback (page 30).
Also selects Auto Surround (
Auto playback
on page 28) and XM Surround (page 53).
UPDOWN
MULTI JOG
MASTER
VOLUME
ENTER
AUDI O /VIDEO MULTI- CHANNEL
RECEIVER
VSX
-
816
STANDBY/ON
PHONES
DVD /LD
TV/ SAT DVR/ VCR VIDEO
CD
CD
-
R/TAPE/MD FM AM
STANDARD
MIDNIGHT/
LOUDNESS
ADVANCED
SURR
ST/DIRECT/
AUTO SURR
LISTENING
MODE
QUICK
SETUP
SETUP
RETURN
TUNING/
STATION
TONE
ANALOG
ATT
SPEAKERS
TUNER
EDIT
DIMMER
MULTI JOG
XM
MCACC
SETUP MIC
DIGITAL INAUDI O RLVIDEO
VIDEO
INPUT
S
-
VIDEO
AUX
SIGNAL
SELECT
SB
ch
PROCESSING
ACOUS TIC
EQ
DIGITAL PRECISION
PROCESSING
DIGITAL PRECISION
PROCESSING
STANDARD
ADVANCED
SURR
ST/DIRECT/
AUTO SURR
LISTENING
MODE
SIGNAL
SELECT
SB
ch
PROCESSING
ACOUSTIC
EQ
MIDNIGHT/
LOUDNESS
QUICK
SETUP
SETUP
RETURN
TUNING/
STATION
TONE
ANALOG
ATT
SPEAKERS
TUNER
EDIT
DIMMER
MULTI JOG
1
89
5 6
32 4
121110
15 16 22 23 2413 14
2017 18 19 21
7
VSX_816.book.fm 22 ページ 2005年12月8日 木曜日 午後6時54分
Controls and displays
05
23
En
English
Français
Deutsch
Nederlands
Italiano
Español
8
PHONES
jack
Use to connect headphones (when connected,
there is no sound output from the speakers).
9
STANDBY/ON
Switches the receiver between on and standby.
10
VIDEO INPUT
See
Connecting to the front panel video terminal
on page 17.
11 MCACC SETUP MIC jack
Use to connect the supplied microphone.
12
MASTER VOLUME
dial
13
DIMMER
Dims or brightens the display.
14
ANALOG ATT
Attenuates (lowers) the level of an analog input
signal to prevent distortion.
15
MIDNIGHT/LOUDNESS
Switches between Midnight and Loudness
listening (page 32).
16
SPEAKERS
Use to change the speaker system (page 54)
and the impedance setting (page 63).
17
TUNING / STATION
Selects the frequency (page 43) and station
presets (page 43) when using the tuner.
18
TUNER EDIT
Press to memorize and name a station for
recall
(page 43).
19
TONE
Press this button to access the bass and treble
controls, which you can then adjust with the
MULTI JOG
dial (page 32).
20
QUICK SETUP
See
Using the Quick Setup
on page 8.
21 System Setup menu controls
SETUP
– Use with the
MULTI JOG
dial to
access the System Setup menu (page 9,
page 34, page 58).
RETURN
– Press to confirm and exit the
current menu.
22
SIGNAL SELECT
Use to select an input signal (page 33).
23
SBch PROCESSING
Selects surround back channel processing or
the virtual surround back mode (page 31).
24 ACOUSTIC EQ
Press to select an Acoustic Calibration EQ
setting (page 30).
Display
1
SIGNAL
indicators
Lights to indicate the type of input signal:
AUTO
– Lights when
AUTO
signal select is
on.
SB
– Depending on the source, this lights
when a signal with surround back channel
encoding is detected.
6
6
0
L
C
R
Ls
Rs
[]
[]
[]
[]
[]
SB
SB
[]
R
40
125
250 4K
13K
L
[ ]
SP
AB
1234567118910
12
1615 17 1813 14 19 20 21
VSX_816.book.fm 23 ページ 2005年12月8日 木曜日 午後6時54分
Controls and displays05
24
En
DIGITAL
– Lights when a digital audio
signal is detected.
2
DIGITAL
– Lights when a Dolby Digital
encoded signal is detected.
ANALOG
– Lights when an analog signal is
detected.
DTS
– Lights when a source with DTS
encoded audio signals is detected.
2
When the
STANDARD
mode is on, this lights
to indicate decoding of a DTS multichannel
signal.
3
2
DIGITAL
When the
STANDARD
mode of the receiver is
on, this lights to indicate decoding of a Dolby
Digital multichannel signal.
4
2
PRO LOGIC II
x
When the (
STANDARD
) Pro Logic II mode of
the receiver is on,
2
PRO LOGIC II
lights to
indicate Pro Logic II decoding.
2
PRO LOGIC
II
x
lights to indicate Pro Logic IIx decoding (see
Listening in surround sound
on page 28).
5 VIR.SB
Lights during Virtual surround back
processing (page 31).
6
DIRECT
Lights when source direct playback is in use.
Direct playback bypasses the tone controls for
the most accurate reproduction of a source.
7 AUTO SURR.
Lights when Auto Surround (see
Auto playback
on page 28) or XM Surround (page 53) is on.
8
ATT
Lights when
ANALOG ATT
is used to
attenuate (reduce) the level of the analog input
signal.
9 SLEEP
Lights when the sleep mode is active (see
Remote control
below).
10
Tuner
indicators
Lights when the mono mode is set
using the
MPX
button.
Lights when a stereo FM broadcast is
being received in auto stereo mode.
Lights when a broadcast is being
received.
11 Speaker indicators
Lights to indicate the current speaker system,
A
and/or
B
(page 54).
12 Character display
13
Neo:6
When the (
STANDARD
) Neo:6 mode of the
receiver is on, this lights to indicate Neo:6
processing.
14
ADV.SURR.
(Advanced Surround)
Lights when one of the Advanced Surround
modes has been selected.
15 WMA9 Pro
Lights to indicate decoding of a WMA9 Pro
signal.
16
MIDNIGHT
Lights during Midnight listening (page 32).
17 D.E.
Lights when Dialog Enhancement (
DIALOG
E)
is switched on (page 32).
18
LOUDNESS
Lights during Loudness listening (page 32).
19 EX
Lights when a Dolby Digital Surround EX
encoded signal is detected.
20 Master volume level
Shows the overall volume level.
21 MCACC channel EQ / Sound Retriever
indicators
These indicators show the EQ balance for each
channel in Checking your Acoustic Calibration
EQ settings on page 39. Also, L and R light
when the Sound Retriever is active (page 32).
VSX_816.book.fm 24 ページ 2005年12月8日 木曜日 午後6時54分
Controls and displays
05
25
En
English
Français
Deutsch
Nederlands
Italiano
Español
Remote control
1 RECEIVER
This switches between standby and on for this
receiver.
2 MULTI CONTROL buttons
Press to select control of other components
(see
Controlling the rest of your system
on
page 46).
3 Number buttons and other receiver/
component controls
Use the number buttons to directly select a
radio frequency (page 43) or the tracks on a
CD, DVD, etc.
DISC (ENTER)
can be used to enter commands
for TV or DTV, and can also be used to select a
disc in a multi-CD player.
The following are accessed by pressing the
RECEIVER
button first:
SLEEP
– Press to change the amount of
time before the receiver switches into
standby (
90 min – 60 min – 30 min – Off
).
You can check the remaining sleep time at
any time by pressing
SLEEP
once.
SB ch
– Selects the surround back channel
mode (page 31) or virtual surround back
mode (page 31).
ANALOG ATT
– Attenuates (lowers) the
level of an analog input signal to prevent
distortion.
SR +
– Switches the SR+ mode on/off
(page 57).
DIMMER
– Dims or brightens the display.
MIDNIGHT/LOUDNESS
– Use Midnight
when listening to movie soundtracks at low
volume. Use Loudness to boost the bass
and treble at low volume (page 32).
D.ACCESS
– After pressing, you can
access a radio station directly using the
number buttons (page 43).
CLASS
– Switches between the three banks
(classes) of radio station presets (page 43).
4 Tuner/component control buttons/
SETUP
The following button controls (except
SETUP
)
can be accessed after you have selected the
corresponding
MULTI CONTROL
button
(
DVD
,
FM
,
AM
,
TV
, etc.)
TOP MENU
– Displays the disc ‘top’ menu
of a DVD.
DTV MENU
– Displays menus on a digital
TV.
ANALOG
AT T
MIDNIGHT/
LOUDNESS
SB ch
DIMMER
SLEEP
SR+
+10
D.AC CESS
CLASS
DISC
RECEIVER
SOURCE
INPUT
SELECT
ENTER
TV CONTROL
SHIFT
VOL
TV DVR
TV CTRL
CD
TUNE
TUNE
ST ST
AUTO SURR
STANDARD ADV.SURR
S.RETRIEVER
SIGNAL SEL
STEREO
INPUT
SELECT
TV CH
MPX
AUDIO
DISP
SUBTITLE
DIALOG E
EFFECT/CH SEL
ACOUSTIC EQ
REC
MUTE
TV VOL
ENTER
REC STOP JUKEBOX
HDD
CH
CH
DVD
TOP MENU
DTV MENU
DTV ON/OFF DTV INFO
T.EDIT
MENU
RETURN
GUIDE
SETUP
CATEGORY
RECEIVER
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
3
2
4
6
7
9
8
5
11
10
12
13
14
15
16
1
VSX_816.book.fm 25 ページ 2005年12月8日 木曜日 午後6時54分
Controls and displays05
26
En
MENU
– Displays the disc menu of DVD-
Video discs. It also displays TV and DTV
menus.
T.EDIT
– Press to memorize and name a
station for recall (page 43).
SETUP
(Press
RECEIVER
first to access)
Use to access the System Setup menu (see
page 34).
GUIDE
– Displays the guides on a digital
TV.
RETURN
– Press to confirm and exit the
current menu (also use to return to the
previous menu with DVDs or to select
closed captioning with DTV).
5

(TUNE/ST +/–) /
ENTER
Use the arrow buttons when setting up your
surround sound system (see page 34). Also
used to control DVD menus/options and for
deck 1 of a double cassette deck player. Use
the
TUNE
/
buttons to find radio
frequencies and use
ST
/
to find preset
stations (page 43).
6 TV CONTROL buttons
These buttons are dedicated to control the TV
assigned to the
TV CTRL
button. Thus if you
only have one TV to hook up to this system
assign it to the
TV CTRL MULTI CONTROL
button. If you have two TVs, assign the main TV
to the
TV CTRL
button (see page 46 for more on
this).
TV
– Use to turn on/off the TV power.
TV VOL +/–
– Use to adjust the TV volume.
INPUT SELECT
– Use to select the TV input
signal.
TV CH +/–
– Use to select channels.
7 Component control buttons
The main buttons (
,
, etc.) are used to
control a component after you have selected it
using the
MULTI CONTROL
buttons.
The controls above these buttons can be
accessed after you have selected the
corresponding
MULTI CONTROL
button (for
example
DVD
,
DVR
or
TV
(when connected to
a DTV)).
DTV ON/OFF
– Switches a digital TV on/off.
DTV INFO
– Use to bring up information
screens on a digital TV.
MPX
– Switches between stereo and mono
reception of FM broadcasts. If the signal is
weak then switching to mono will improve
the sound quality (page 43).
AUDIO
– Changes the audio language or
channel on DVD discs.
DISP
– Switches between named station
presets and radio frequencies (page 44).
SUBTITLE
– Displays/changes the subtitles
included in multilingual DVD-Video discs.
CH +/–
– Use to select channels when
using a TV, VCR, DVR, etc.
The following DVR controls can be accessed by
pressing
SHIFT
:
ì
REC
– Starts recording.
REC STOP
– Stops recording.
JUKEBOX
– Switches to the Jukebox
feature.
HDD
/
DVD
– These buttons switch between
the hard disk and DVD controls for DVD/
HDD recorders.
8 RECEIVER CONTROL buttons
STANDARD
– Press for Standard decoding
and to switch between the various Pro
Logic IIx and Neo:6 options (page 28).
ADV.SURR. – Use to switch between the
various surround modes (page 29).
STEREO – Switches between direct and
stereo playback. Direct playback bypasses
the tone controls and any other signal
processing for the most accurate
reproduction of a source (page 30). Also
selects the Auto Surround mode (Auto
playback on page 28).
VSX_816.book.fm 26 ページ 2005年12月8日 木曜日 午後6時54分
Controls and displays
05
27
En
English
Français
Deutsch
Nederlands
Italiano
Español
AUTO SURR
– Selects Auto Surround
(
Auto playback
on page 28) and XM
Surround (page 53).
DIALOG E
– Use to make dialog stand out
when watching TV or a movie (page 32).
S. RETRIEVER
– Press to restore CD quality
sound to compressed audio sources
(page 32).
ACOUSTIC EQ
– Press to select an
Acoustic Calibration EQ setting (page 30).
SIGNAL SEL
– Use to select an input signal
(page 33).
9 SHIFT
Press to access the DVR controls (above the
component control buttons) as well as some
receiver controls.
10 INPUT SELECT
Use to select the input source (use
SHIFT
for
INPUT SELECT
).
11
SOURCE
Press to turn on/off other components
connected to the receiver (see page 46 for
more on this).
12 Character display (LCD)
This display shows information when
transmitting control signals.
The following commands are shown when
you’re setting the remote to control other
components (see
Controlling the rest of your
system
on page 46):
SETUP
– Indicates the setup mode, from
which you choose the options below.
PRESET
– See
Selecting preset codes
directly
on page 47.
DIRECT F
– See
Direct function
on page 48.
ERASE
– See
Erasing one of the remote
control button settings
on page 47.
RESET
– See
Erasing all of the remote
control presets
on page 47.
READ ID
– See
Confirming preset codes
on
page 48.
13 RECEIVER
Switches the remote to control the receiver
(used to select the green commands above the
number buttons (
DIMMER
, etc). Also use this
button to set up surround sound (page 9,
page 34).
14 VOL +/–
Use to set the listening volume.
15 MUTE
Mutes the sound or restores the sound if it has
been muted (adjusting the volume also
restores the sound).
16 EFFECT/CH SEL
Press repeatedly to select a channel, then
use
+/–
to adjust the level
(see
Tip
on
page 42). Also adjusts the level of the
Advanced Surround effects, Dolby Pro
Logic IIx Music, and Neo:6 Music
parameters (page 29). You can then use
the
+/–
buttons to make these
adjustments.
Operating range of remote control
The remote control may not work properly if:
There are obstacles between the remote
control and the receiver's remote sensor.
Direct sunlight or fluorescent light is
shining onto the remote sensor.
The receiver is located near a device that is
emitting infrared rays.
The receiver is operated simultaneously
with another infrared remote control unit.
D
O
W
N
30
30
23 ft (7m)
D
O
W
N
VSX_816.book.fm 27 ページ 2005年12月8日 木曜日 午後6時54分
Listening to your system06
28
En
Chapter 6:
Listening to your system
Important
Certain features explained in this section
will not be possible depending on the
source (for example, PCM 88.2 / 96 kHz,
DTS 96 kHz (24 bit) or WMA 9 Pro sources).
Auto playback
The simplest, most direct listening option is the
Auto Surround feature. With this, the receiver
automatically detects what kind of source
you’re playing and selects multichannel or
stereo playback as necessary.
1
While listening to a source, press AUTO
SURR for auto playback of a source.
Press repeatedly until AUTOSURR. shows
briefly in the display (it will then show the
decoding or playback format). Check the
digital format indicators in the display to see
how the source is being processed.
When listening to XM Radio, AUTO SURR
selects the XM Surround feature (page 53).
Listening in surround sound
Using this receiver, you can listen to any
source in surround sound. However, the
options available will depend on your speaker
setup and the type of source you’re listening to.
If you connected surround back speakers, see
also Using surround back channel processing
on page 31.
2
The following modes provide basic surround
sound for stereo and multichannel sources.
While listening to a source, press
STANDARD.
If necessary, press repeatedly to select a
listening mode.
If the source is Dolby Digital, DTS, or Dolby
Surround encoded, the proper decoding
format will automatically be selected and
shows in the display.
3
With two channel sources, you can select from:
2 Pro Logic IIx MOVIE – Up to 7.1
channel sound, especially suited to movie
sources
2 Pro Logic IIx MUSIC – Up to 7.1
channel sound, especially suited to music
sources
2 Pro Logic IIx GAME – Up to 7.1
channel sound, especially suited for video
games
2 PRO LOGIC – 4.1 channel surround
sound (sound from the surround speakers
is mono)
Neo:6 CINEMA – 6.1 channel sound,
especially suited to movie sources
Note
1• Stereo surround (matrix) formats are decoded accordingly using Neo:6 CINEMA or 2 Pro Logic IIx MOVIE (see Listening
in surround sound above for more on these decoding formats).
• The Auto Surround feature is canceled if you connect headphones or select the multichannel analog inputs.
AUTO SURR
STANDARD ADV.SURR
STEREO
2 If surround back processing (page 31) is switched to OFF, or the surround back speakers are set to NO (this happens auto-
matically if the Surround back speaker setting on page 34 is set to anything but Normal (SB)), 2 Pro Logic IIx becomes 2 Pro
Logic II (5.1 channel sound).
3 If surround back processing (page 31) is switched to OFF, or the surround back speakers are set to NO (page 40), 2 Pro Logic
IIx becomes 2 Pro Logic II (5.1 channel sound).
AUTO SURR
STANDARD ADV.SURR
STEREO
05_playing_sources.fm 28 ページ 2005年12月14日 水曜日 午後3時12分
Listening to your system
06
29
En
English
Français
Deutsch
Nederlands
Italiano
Español
Neo:6 MUSIC
– 6.1 channel sound,
especially suited to music sources
With multichannel sources, if you have
connected surround back speaker(s) and have
selected
SB ON
, you can select (according to
format):
2
Pro Logic IIx MOVIE
– See above
2
Pro Logic IIx MUSIC
– See above
Dolby Digital EX
– Creates surround back
channel sound for 5.1 channel sources and
provides pure decoding for 6.1 channel
sources (like Dolby Digital Surround EX)
DTS-ES
– Allows you to hear 6.1 channel
playback with DTS encoded sources
Using the Advanced surround effects
The Advanced surround effects can be used for
a variety of additional surround sound effects.
Most Advanced Surround modes are designed
to be used with film soundtracks, but some
modes are also suited for music sources. Try
different settings with various soundtracks to
see which you like.
1
Press ‘
ADV.SURR
’ repeatedly to select a
listening mode.
ADV. MOVIE
– Suitable for movie sources.
ADV. MUSIC
– Suitable for music sources.
TV SURR.
– Provides surround sound for
both mono and stereo TV sources.
SPORTS
– Suitable for sports programs.
ADV. GAME
– Suitable for video games.
EXPANDED
– Simulates multichannel
surround sound for two-channel sources.
2
7-STEREO
– Gives multichannel sound to a
stereo source, using all of your speakers.
VIR. SURR
– A virtual surround effect using
just the subwoofer and front speakers.
PHONESUR.
– Creates the effect of overall
surround with headphones.
Setting the effect options
When using surround effects, there are a
number of settings you can adjust.
1 Press
EFFECT/CH SEL
repeatedly to select
the setting you want to adjust.
Depending on the current status / mode of the
receiver, certain options may not appear.
Check the table below for notes on this.
2
Use the +/– buttons
to set it as necessary.
See the table below for the options available for
each setting. The defaults, if not stated, are
listed in bold.
3
Press EFFECT/CH SEL again to adjust
other settings
.
Note
1• If you press
ADVANCED SURROUND
when the headphones are connected, the
PHONES SURROUND
mode will automat-
ically be selected.
Depending on the source and the sound mode you have selected, you may not get sound from the surround back speakers
in your setup. For more on this, refer to
Using surround back channel processing
on page 31.
• When an Advanced Surround listening mode is selected, the effect level can be adjusted using the
EFFECT
parameter in
Setting the effect options
above.
2 Use with Dolby Pro Logic for a stereo surround effect (stereo field is wider than Standard modes with Dolby Digital sources).
AUTO SURR
STANDARD ADV.SURR
STEREO
CH CH
Setting
What it does
Options
Center
Width
a
(Applicable
only when
using a cen-
ter speaker)
Spreads the center channel
between the front right and left
speakers, making it sound
wider (higher settings) or
narrower (lower settings).
0 to 7
Default:
3
Dimension
a
Adjusts the surround sound
balance from front to back,
making the sound more distant
(minus settings), or more
forward (positive settings).
–3 to +3
Default:
0
Panorama
a
Extends the front stereo image
to include surround speakers
for a ‘wraparound’ effect.
OFF
ON
05_playing_sources.fm 29 ページ 2005年12月14日 水曜日 午後3時12分
Listening to your system06
30
En
Listening in stereo
When you select
STEREO
or
DIRECT
, you will
hear the source through just the front left and
right speakers (and possibly your subwoofer
depending on your speaker settings).
Dolby Digital and DTS multichannel sources
are downmixed to stereo.
While listening to a source, press
STEREO
for stereo playback.
Press repeatedly to switch between:
STEREO
– The audio is heard with your
surround settings and you can still use the
Midnight, Loudness, and Tone functions.
DIRECT
– Bypass all effects and surround
settings so that the audio remains as close
to the source audio signal as possible.
1
AUTO SURR.
– See
Auto playback
on
page 28 for more on this.
Listening with Acoustic
Calibration EQ
Default setting:
OFF
/
ALL CH
(after the
Auto MCACC Setup or EQ Auto Setting)
You can listen to sources using the Acoustic
Calibration Equalization set in
Automatically
setting up for surround sound (MCACC)
on
page 9 or
Acoustic Calibration EQ
on page 37.
Refer to these pages for more on Acoustic
Calibration Equalization.
While listening to a source, press
ACOUSTIC EQ.
Press repeatedly to select between:
ALL CH
– No special weighting is given to
any one channel.
F. ALIGN
– All speakers are heard in
accordance with the front speaker
settings.
CUSTOM 1/2
– Custom settings
EQ OFF
– Switches Acoustic Calibration
EQ off.
The MCACC indicator on the front panel lights
when Acoustic Calibration EQ is active.
2
Center
Image
b
(Applicable
only when
using a cen-
ter speaker)
Adjusts the center image to
create a wider stereo effect with
vocals. Adjust the effect from
0
(all center channel sent to front
right and left speakers) to
10
(center channel sent to the
center speaker only).
0 to 10
Default:
3
Effect
Sets the effect level for the
currently selected Advanced
Surround mode (each mode
can be set separately).
10 to 90
a Only available with 2ch sources in Dolby Pro Logic IIx Mu-
sic mode (also available with
2
Pro Logic II
5.1sound).
b Only available with 2ch sources in Neo:6 Music mode.
Note
1 If you switch on Midnight listening, Loudness, Dialog Enhancement, the Sound Retriever or the tone controls when
DIRECT
is selected, the receiver automatically switches to
STEREO
.
Setting
What it does
Options
AUTO SURR
STANDARD ADV.SURR
STEREO
2• You can’t use Acoustic Calibration EQ with
DVD 5.1ch
, WMA9 Pro or XM Surround, and it has no effect with headphones.
• If you switch on Acoustic Calibration EQ when
DIRECT
is selected, the receiver automatically switches to
STEREO
.
S.RETRIEVER
SIGNAL SEL
DIALOG E
C/C S
ACOUSTIC EQ
05_playing_sources.fm 30 ページ 2005年12月14日 水曜日 午後3時12分
Listening to your system
06
31
En
English
Français
Deutsch
Nederlands
Italiano
Español
Using surround back channel
processing
Default setting:
SB ON
You can have the receiver automatically use 6.1
decoding for 6.1 encoded sources (for
example, Dolby Digital EX or DTS-ES), or you
can choose to always use 6.1 decoding (for
example, with 5.1 encoded material). With 5.1
encoded sources, a surround back channel
will be generated, but the material may sound
better in the 5.1 format for which it was origi-
nally encoded (in which case, you can simply
switch surround back processing off).
1
The table below indicates when you will hear
the surround back channel (
ì
=Sound plays
through surround back speaker(s)).
Press
SB ch
(
SB ch PROCESSING
) to select
a surround back channel option.
Each press cycles through the following:
SB ON
– 6.1 decoding is always used (for
example, a surround back channel will be
generated for 5.1 encoded material)
SB AUTO
– Automatically switches to 6.1
decoding for 6.1 encoded sources (for
example, Dolby Digital EX or DTS-ES)
SB OFF
– Maximum 5.1 playback
Using Virtual Surround Back (VSB)
When you’re not using surround back
speakers, selecting this mode allows you to
hear a virtual surround back channel through
your surround speakers. You can choose to
listen to sources with no surround back
channel information, or if the material sounds
better in the format (for example, 5.1) for which
it was originally encoded, you can have the
receiver only apply this effect to 6.1 encoded
sources like Dolby Digital EX or DTS-ES.
2
The table indicates when you will hear the
virtual surround back channel (
ì
=Sound
plays through surround speaker(s)).
Press
SB ch
(
SB ch PROCESSING
) to select
a virtual surround back channel option.
Each press cycles through the following:
VSB ON
– Virtual Surround Back is always
used (for example, on 5.1 encoded
material)
VSB AUTO
– Virtual Surround Back is
automatically applied to 6.1 encoded
sources (for example, Dolby Digital EX or
DTS-ES)
VSB OFF
– Virtual Surround Back mode is
switched off
Note
1 You can’t use the surround back channel with headphones, the
STEREO
/
DIRECT
mode, or if the surround back speaker is
set to
NO
in
Speaker Setting
on page 40. Also, the
Surround back speaker setting
on page 34 must be set to
Normal (SB)
to hear
the surround back channel.
2 You can’t use virtual surround back with headphones, the
STEREO
/
DIRECT
mode, or if the surround speaker is set to
NO
in
Speaker Setting
on page 40 (however, the surround
back
speaker
must
be set to
NO
).
Type of source
SBch
Processing /
Virtual SB
mode
Standard
Advanced
surround
Multichannel
sources
Stereo sources
2
Pro Logic II x
2
Pro Logic
Neo:6
Dolby Digital EX/DTS-ES/
WMA9 Pro encoded
multichannel sources with
6.1ch surround
ON
ì
ì
a
AUTO
ì
ì
a
Dolby Digital/DTS/WMA9 Pro
encoded multichannel
sources
ON
ì
ì
a
AUTO
ì
a
Dolby Digital/DTS/WMA9 Pro
encoded stereo source; other
digital stereo source
ON
ì
ì
a,
b
ì
ì
a
AUTO
ì
c
ìì
a
05_playing_sources.fm 31 ページ 2005年12月14日 水曜日 午後3時12分
Listening to your system06
32
En
Using Midnight and Loudness
The Midnight listening feature allows you to
hear effective surround sound of movies at low
volume levels. The effect automatically adjusts
according to the volume at which you’re
listening. The Loudness listening feature can
be used to get good bass and treble from
music sources at low volume levels.
Press MIDNIGHT/LOUDNESS to switch
between MIDNIGHT, LOUDNESS, and OFF.
Using the Sound Retriever
When audio data is removed during the
compression process, sound quality often
suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
technology that helps bring CD quality sound
back to compressed 2-channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
1
Press
S. RETRIEVER to switch the sound
retriever on or off.
Enhancing dialog
Default setting:
OFF
The Dialog Enhancement feature localizes
dialog in the center channel to make it stand
out from other background sounds in a TV or
movie soundtrack.
Press DIALOG E to switch dialog
enhancement on or off.
Using the tone controls
Depending on what you are listening to, you
may want to adjust the bass or treble using the
front panel tone control.
1 Press TONE to select the frequency you
want to adjust.
Press to switch between
BASS
and
TREBLE
.
2 Use the
MULTI JOG
dial to change the
amount of bass or treble as necessary.
Wait about five seconds for your changes to be
input automatically.
Analog 2-channel (stereo)
sources
ON
ì
ì
b
ìì
AUTO
ì
c
ìì
a Excluding WMA9 Pro format
b Only applicable when using the Virtual Surround Back mode.
c Not applicable when using the Virtual Surround Back mode.
Type of source
SBch
Processing /
Virtual SB
mode
Standard
Advanced
surround
Multichannel
sources
Stereo sources
2
Pro Logic II x
2
Pro Logic Neo:6
Note
1 The Sound Retriever is only applicable to 2-channel sources.
05_playing_sources.fm 32 ページ 2005年12月14日 水曜日 午後3時12分
Listening to your system
06
33
En
English
Français
Deutsch
Nederlands
Italiano
Español
Playing other sources
1 Turn on the power of the playback
component.
2 Turn on the power of the receiver.
3 Select the source you want to playback.
Use the input select buttons.
1
4 Start playback of the component you
selected in step 1.
Choosing the input signal
Default setting:
AUTO
You need to hook up a component to both
analog and digital inputs on the rear of the
receiver to select between input signals.
2
Press
SIGNAL SEL (SIGNAL SELECT
) to
select the input signal corresponding to the
source component.
Each press cycles through the options as
follows:
AUTO
– This is the default setting. The
receiver selects the first available signal in
the following order:
DIGITAL
;
ANALOG
.
ANALOG
– Selects an analog signal.
DIGITAL
– Selects an optical or coaxial
digital signal.
When set to
DIGITAL
or
AUTO
,
2
DIGITAL
lights when a Dolby Digital signal is input, and
DTS
lights when a DTS signal is input.
Selecting the multichannel
analog inputs
If you have connected a decoder or a DVD
player with multichannel analog outputs to this
receiver (page 14), you must select the analog
multichannel inputs for surround sound.
3
1 Make sure you have set the playback
source to the proper output setting.
For example, you might need to set your DVD
player to output multichannel analog audio.
2 Press
DVD/LD
.
3 Press
SIGNAL SELECT
to select the
multichannel analog inputs.
DVD 5.1ch
shows in the display and the
ANALOG
indicator lights.
Note
1 If your source is the TV’s built-in tuner, switch to the channel you want to watch, otherwise make sure that the TV’s video input
is set to this receiver (For example, if you connected this receiver to the
VIDEO
jacks on your TV, make sure that the
VIDEO
input
is selected). Turn down the volume of your TV so that all the sound is coming from the speakers connected to this receiver.
2• This receiver can only play back Dolby Digital, PCM (32 kHz to 96 kHz), DTS and WMA9 Pro digital signal formats. With other
digital signal formats, set to
ANALOG
.
• You may get digital noise when a LD or CD player compatible with DTS is playing an analog signal. To prevent noise, make
the proper digital connections (
Connecting other audio components
on page 15) and set the signal input to
DIGITAL
.
• Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.
3• During playback from the multichannel inputs, you can’t use any of the sound features/modes and only the volume and
channel levels can be set.
• You can’t listen to your speaker B (Second Zone) system during playback from the multichannel inputs.
05_playing_sources.fm 33 ページ 2005年12月14日 水曜日 午後3時12分
The System Setup menu07
34
En
Chapter 7:
The System Setup menu
Making receiver settings from
the System Setup menu
The following section shows you how to make
detailed settings to specify how you’re using
the receiver (for example, if you want to set up
two speaker systems in separate rooms), and
also explains how to fine-tune individual
speaker system settings to your liking.
1 Switch on the receiver and your TV.
Use the
RECEIVER
button to switch on.
1
2 Press RECEIVER on the remote control,
then press the SETUP button.
2
An on-screen display (OSD) appears on your
TV. Use
///
and
ENTER
on the remote
control to navigate through the screens and
select menu items. Press
RETURN
to confirm
and exit the current menu.
3 Select the setting you want to adjust.
Surr Back System
– Specify how you are
using your surround back speakers (see
Surround back speaker setting
below).
Auto MCACC
– This is a quick and
effective automatic surround setup (see
Automatically setting up for surround
sound (MCACC)
on page 9).
Manual MCACC
– Fine tune your speaker
settings and customize the Acoustic
Calibration EQ (see
Manual MCACC
speaker setup
below).
Manual SP Setup
– Specify the size,
number, distance and overall balance of
the speakers you’ve connected (see
Manual speaker setup
on page 39).
Input Assign
– Specify what you’ve
connected to the digital and component
video inputs (see
The Input Assign menu
on page 58).
Other Setup
– Make customized settings
to reflect how you are using the receiver
(see
The Other Setup menu
on page 59).
Surround back speaker setting
Default setting:
Normal (SB)
There are several ways you can use the
surround back speaker channels with this
system. In addition to a normal home theater
setup where they are used for the surround
back speakers, they can be used for bi-amping
the front speakers or as a separate speaker
system in another room.
Note
1 If headphones are connected to the receiver, disconnect them.
2• You can’t use the System Setup menu when the XM Radio input is selected.
• Press
SETUP
at any time to exit the System Setup menu.
RECEIVER
SOURCE
INPUT
SELECT
TV DVR
TV CTRL
CD
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
+10
D.ACCESS
CLASS
DISC
ENTER
TV CONTROL
VOL
TUNE
TUNE
ST ST
INPUT
SELECT
TV CH
TV VOL
ENTER
TOP MENU
DTV MENU
T. EDIT
MENU
RETURN
GUIDE
SETUP
CATEGORY
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
VSX_816.book.fm 34 ページ 2005年12月8日 木曜日 午後6時54分
The System Setup menu
07
35
En
English
Français
Deutsch
Nederlands
Italiano
Español
1 Select ‘Surr Back System’ from the
System Setup menu.
See
Making receiver settings from the System
Setup menu
above if you’re not already at this
screen.
2 Select the surround back speaker
setting.
Normal (SB)
– Select for normal home
theater use with surround back speakers in
your main (speaker system A) setup.
Second Zone
– Select to use the (surround
back) B speaker terminals to listen to
stereo playback in another room (see
Second Zone speaker B setup
on page 54).
Front Bi-Amp
– Select this setting if you’re
bi-amping your front speakers (see
Bi-
amping your front speakers
on page 55).
3 When you’re finished, press RETURN.
You return to the System Setup menu.
Manual MCACC speaker setup
You can use the settings in the Manual MCACC
setup menu to make detailed adjustments
when you’re more familiar with the system.
Before making these settings, you should have
already completed
Automatically setting up for
surround sound (MCACC)
on page 9.
You only need to make these settings once
(unless you change the placement of your
current speaker system or add new speakers).
Important
For some of the settings below, you’ll have
to connect the setup microphone to the
front panel and place it about ear level at
your normal listening position. See
Automatically setting up for surround
sound (MCACC)
on page 9 if you’re unsure
how to do this. Also see
Other problems
when using the Auto MCACC Setup
on
page 11 for notes regarding background
noise and other possible interference.
If you’re using a subwoofer, switch it on
and turn up the volume as necessary.
1 Select ‘Manual MCACC’ from the
System Setup menu.
See
Making receiver settings from the System
Setup menu
above if you’re not already at this
screen.
2 Select the setting you want to adjust.
If you’re doing this for the first time, you might
want to make these settings in order.
Fine Ch Level
– Make fine adjustments to
the overall balance of your speaker system
(see
Fine Channel Level
below).
Fine SP Distance
– Make precise delay
settings for your speaker system (see
Fine
Speaker Distance
on page 36).
The last five settings are specifically for
customizing the parameters explained in
Acoustic Calibration EQ
below:
EQ AUTO Setting
– Measure the acoustic
characteristics of your room and
automatically adjust the frequency balance
of your speaker system (see
Setting the
Acoustic Calibration EQ automatically
below).
EQ Data Copy
– Copy Acoustic Calibration
EQ settings for manual adjustment (see
Copying your Acoustic Calibration EQ
settings
below).
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
1.Surround Back System
Surr Back System
Normal (SB) ]
: Finish
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
VSX_816.book.fm 35 ページ 2005年12月8日 木曜日 午後6時54分
The System Setup menu07
36
En
EQ CUSTOM1/2 Adjust
– Make detailed
manual adjustments to your custom
Acoustic Calibration EQ settings (see
Setting the Acoustic Calibration EQ
manually
on page 38).
EQ Data Check
– Check the
ALL CH
ADJUST
,
FRONT ALIGN
and custom
settings using the on-screen display (see
Checking your Acoustic Calibration EQ
settings
on page 39).
Fine Channel Level
Default setting:
0dB
(all channels)
You can achieve better surround sound by
properly adjusting the overall balance of your
speaker system. The following setting can help
you make detailed adjustments that you may
not achieve using the
Manual speaker setup
on
page 39.
1 Select ‘Fine Ch Level’ from the Manual
MCACC setup menu.
You’ll hear test tones from each speaker in
turn. Since the left speaker is the main
reference speaker, the level is fixed.
Caution
The test tones used in the System Setup
are output at high volume (the volume
increases to
–18 dB
automatically).
2 Select each channel in turn and adjust
the levels
(
+/– 10dB
)
as necessary.
Use
/
to adjust the volume of the speaker
you selected to match the reference speaker.
When it sounds like both tones are the same
volume, press
ENTER
to confirm and continue
to the next channel.
For comparison purposes, the reference
speaker will change depending on which
speaker you select.
If you want to go back and adjust a
channel, simply use
/
to select it.
3 When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
Fine Speaker Distance
Default setting:
10.0 ft
(all channels)
For proper sound depth and separation with
your system, it is necessary to add a slight bit
of delay to some speakers so that all sounds
will arrive at the listening position at the same
time. The following setting can help you make
detailed adjustments that you may not achieve
using the
Manual speaker setup
below.
1 Select ‘Fine SP Distance’ from the
Manual MCACC setup menu.
The volume increases to the reference level.
2 Adjust the distance of the left channel
from the listening position.
After pressing
ENTER
, test tones will be output.
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
3a.Fine Channel Level
Please Wait... 20
Caution!
Loud test tones
will be output.
:Cancel
3a.Fine Channel Level
L +  0.0dB (Reference)
R [ 0.0dB ]
C +  1.0dB
LS [ -3.0dB ]
RS [+ 10.0dB ]
SBL [– 10.0dB ]
SBR [+ 9.5dB ]
SW [– 1.5dB ]
:Finish
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
3b.Fine SP Distance
L(Reference)
10.0ft
ENTER:Next :Cancel
VSX_816.book.fm 36 ページ 2005年12月8日 木曜日 午後6時54分
The System Setup menu
07
37
En
English
Français
Deutsch
Nederlands
Italiano
Español
3 Select each channel in turn and adjust
the distance as necessary.
Use
/
to adjust the delay of the speaker
you selected to match the reference speaker.
The delay is measured in terms of speaker
distance from
0.5
to
45.0
feet.
Listen to the reference speaker and use it to
measure the target channel. From the listening
position, face the two speakers with your arms
outstretched pointing at each speaker. Try to
make the two tones sound as if they are
arriving simultaneously at a position slightly in
front of you and between your arm span.
When it sounds like the delay settings are
matched up, press
ENTER
to confirm and
continue to the next channel.
For comparison purposes, the reference
speaker will change depending on which
speaker you select.
If you want to go back and adjust a
channel, simply use
/
to select it.
4 When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
Acoustic Calibration EQ
Acoustic Calibration Equalization is a kind of
room equalizer for your speakers (excluding
the subwoofer). It works by measuring the
acoustic characteristics of your room and
neutralizing the ambient characteristics that
can color the original source material. This
provides a ‘flat’ equalization setting. If you’re
not satisfied with the automatic adjustment,
you can also adjust these settings manually to
get a frequency balance that suits your tastes.
Setting the Acoustic Calibration EQ
automatically
If you have already completed
Automatically
setting up for surround sound (MCACC)
on
page 9,
ALL CH ADJUST
and
FRONT ALIGN
(below) should already be set. Therefore, if you
want to adjust your settings manually, you can
skip to
Setting the Acoustic Calibration EQ
manually
below.
1 Select ‘EQ AUTO Setting’ from the
Manual MCACC setup menu.
Make sure the microphone is connected.
If you’re using a subwoofer, it is
automatically detected every time you
switch on the system. Make sure it is on
and the volume is at the middle position.
See
Other problems when using the Auto
MCACC Setup
on page 11 for notes
regarding high background noise levels
and other possible interference.
2 Wait for the Auto MCACC Setup to
finish.
As the receiver outputs test tones, the
frequency balance is adjusted automatically
for the following settings:
3b.Fine SP Distance
L 10.0ft
(
Reference
)
R [ 9.0ft ]
C 9.5ft
LS [ 6.0ft ]
RS [ 6.5ft ]
SBL [ 6.0ft ]
SBR [ 6.5ft ]
SW [ 12.5ft ]
:Finish
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
3c.EQ AUTO Setting
Set microphone.
Turn on Subwoofar.
:Cancel
3c.EQ AUTO Setting
Now Analyzing
Environment Check
Ambient Noise [ ]
Microphone [ ]
Speaker YES/NO [ ]
:Cancel
3c.EQ AUTO Setting
Now Analyzing
Surround Analyzing
Channel Level [ ]
Acoustic Cal EQ [ ]
:Cancel
VSX_816.book.fm 37 ページ 2005年12月8日 木曜日 午後6時54分
The System Setup menu07
38
En
ALL CH ADJUST – A ‘flat’ setting where all
the speakers are set individually so no
special weighting is given to any one
channel.
FRONT ALIGN – All speakers are set in
accordance with the front speaker settings
(no equalization is applied to the front left
and right channels).
You return to the Acoustic Cal EQ setup menu
after the Acoustic Calibration Equalization is
set.
Copying your Acoustic Calibration EQ
settings
If you want to manually adjust the Acoustic
Calibration EQ (see Setting the Acoustic
Calibration EQ manually below), we
recommend copying the ALL CH ADJUST or
the FRONT ALIGN settings from the EQ AUTO
setup above (or from Automatically setting up
for surround sound (MCACC) on page 9) to one
of the custom settings. Instead of just a flat EQ
curve, this will give you a reference point from
which to start.
1 Select ‘EQ Data Copy’ from the Manual
MCACC setup menu.
2 Select CUSTOM1 or CUSTOM2 then use
/ to select the setting you want to
copy.
You can also copy from one custom setting
to another. For more on the ALL CH
ADJUST and FRONT ALIGN settings, see
Setting the Acoustic Calibration EQ
automatically above.
3 Select ‘OK’ to copy and confirm.
Setting the Acoustic Calibration EQ
manually
Before manually adjusting the Acoustic
Calibration EQ, we recommend copying the
ALL CH ADJUST or the FRONT ALIGN
settings from the auto setup above (or from
Automatically setting up for surround sound
(MCACC) on page 9) to one of the custom
settings. Instead of just a flat EQ curve, this will
give you a reference point from which to start
(see Copying your Acoustic Calibration EQ
settings above for how to do this).
1 Select ‘EQ CUSTOM1 Adjust or EQ
CUSTOM2 Adjust’ from the Manual MCACC
setup menu.
2 Select which method you would like to
use to adjust the overall frequency balance.
It is best to choose whichever one you copied
to the custom setting in Copying your Acoustic
Calibration EQ settings above.
ALL CH ADJUST – All the speakers can be
set independently so no special weighting
is given to any one channel. When
adjusting, test tones will sound for each
individual channel.
FRONT ALIGN – Speakers are set in
accordance with the front speaker
settings. The sound of the test tone will
alternate between the left front (reference)
speaker and the target speaker.
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
3d.EQ Data Copy
:Cancel
TO FROM
CUSTOM1 CUSTOM1
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
3d.EQ Data Copy
:Cancel
TO FROM
CUSTOM1 ALL CH ADJ
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
3e.EQ CUSTOM1 Adjust
Test Tone Type
ALL CH ADJUST
ENTER:Next :Cancel
06_System_setup.fm 38 ページ 2005年12月9日 金曜日 午前10時26分
The System Setup menu
07
39
En
English
Français
Deutsch
Nederlands
Italiano
Español
3 Select the channel(s) you want and
adjust to your liking.
Use
/
to select the channel.
Use
/
to select the frequency and
/
to
boost or cut the EQ. When you’re finished, go
back to the top of the screen and use
/
to
select the next channel.
The front speakers can’t be adjusted if you
selected
FRONT ALIGN
.
The
OVER
indicator shows in the display if
the frequency adjustment is too drastic
and might distort. If this happens, bring the
level down until
OVER
disappears from the
display.
Tip
Changing the frequency curve of one
channel too drastically will affect the
overall balance. If the speaker balance
seems uneven, you can raise or lower
channel levels using test tones with the
TRIM
feature. Use
/
to select
TRIM
then use
/
to raise or lower the
channel level for the current speaker.
4 When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
Checking your Acoustic Calibration EQ
settings
After you have completed an automatic or
manual Acoustic Calibration EQ adjustment,
you can check the
ALL CH ADJUST
,
FRONT
ALIGN
and custom settings using the on-
screen display.
1 Select ‘EQ Data Check’ from the Manual
MCACC setup menu.
2 Select the setting you want to check.
It is useful to do this while a source is
playing so you can compare the different
settings.
3 Select the channels you want, pressing
ENTER when you’re finished checking each
one.
4 When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
Manual speaker setup
This receiver allows you to make detailed
settings to optimize the surround sound
performance. You only need to make these
settings once (unless you change the
placement of your current speaker system or
add new speakers.).
These settings are designed to fine-tune your
system, but if you’re satisfied with the settings
made in
Automatically setting up for surround
sound (MCACC)
on page 9, it isn’t necessary to
make all of these settings.
Caution
The test tones used in the System Setup
are output at high volume (the volume
increases to
–18 dB
automatically).
40Hz : [+ 1.0dB ]
125Hz : [ 0.0dB ]
250Hz : [ 0.0dB ]
4kHz : [ 0.0dB ]
13kHz : [ 0.0dB ]
TRIM : [ 0.0dB ]
3e.EQ CUSTOM1 Adjust
:Finish
Test Tone Type:
"ALL CH ADJUST"
Left
40Hz : + 1.0dB
125Hz : [ 0.0dB ]
250Hz : [ 0.0dB ]
4kHz : [ 0.0dB ]
13kHz : [ 0.0dB ]
TRIM : [ 0.0dB ]
3e. EQ CUSTOM1 Adjust
:Finish
Test Tone Type:
"ALL CH ADJUST"
[ Left ]
3.Manual MCACC
:Return
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
40Hz :
+
1.0dB
125Hz : 0.0dB
250Hz : 0.0dB
4kHz : 0.0dB
13kHz : 0.0dB
TRIM : 0.0dB
3g.EQ Data Check
:Return
ALL CH ADJUST
[ Left EQ ]
06_System_setup.fm 39 ページ 2005年12月9日 金曜日 午前10時26分
The System Setup menu07
40
En
1 Select ‘Manual SP Setup’ then press
ENTER.
2 Select the setting you want to adjust.
If you are doing this for the first time, you may
want to adjust these settings in order:
Speaker Setting
– Specify the size and
number of speakers you’ve connected
(page 40).
Crossover Network
– Specify which
frequencies will be sent to the subwoofer
(see
Crossover Network
below).
Channel Level
– Adjust the overall balance
of your speaker system (page 41).
Speaker Distance
– Specify the distance
of your speakers from the listening position
(page 42).
3 Make the adjustments necessary for
each setting, pressing RETURN to confirm
after each screen.
Speaker Setting
Use this setting to specify your speaker
configuration (size, number of speakers). It is a
good idea to make sure that the settings made
in
Automatically setting up for surround sound
(MCACC)
on page 9 are correct.
1 Select ‘Speaker Setting’ from the
Manual SP Setup menu.
2 Choose the set of speakers that you
want to set then select a speaker size.
Use
/
to select the size (and number) of
each of the following speakers:
Front
– Select
LARGE
if your front
speakers reproduce bass frequencies
effectively, or if you didn’t connect a
subwoofer. Select
SMALL
to send the bass
frequencies to the subwoofer.
1
Center
– Select
LARGE
if your center
speaker reproduces bass frequencies
effectively, or select
SMALL
to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect a center
speaker, choose
NO
(the center channel is
sent to the front speakers).
Surr
– Select
LARGE
if your surround
speakers reproduce bass frequencies
effectively. Select
SMALL
to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect surround
speakers choose
NO
(the sound of the
surround channels is sent to the front
speakers or a subwoofer).
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
4.Manual SP Setup
:Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
Note
1 If you select
SMALL
for the front speakers the subwoofer will automatically be fixed to
YES
. Also, the center, surround, and
surround back speakers can’t be set to
LARGE
if the front speakers are set to
SMALL
. In this case, all bass frequencies are sent
to the subwoofer.
4.Manual SP Setup
:Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
4a.Speaker Setting
Front SMALL
Center [ SMALL ]
Surr [ SMALL ]
SB [
SMALL x2
]
SUB W. [ YES ]
:Finish
VSX_816.book.fm 40 ページ 2005年12月8日 木曜日 午後6時54分
The System Setup menu
07
41
En
English
Français
Deutsch
Nederlands
Italiano
Español
SB
– Select the number of surround back
speakers you have (one, two or none).
Select
LARGE
if your surround back
speakers reproduce bass frequencies
effectively. Select
SMALL
to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect surround
back speakers choose
NO
.
1
SUB W.
– LFE signals and bass
frequencies of channels set to
SMALL
are
output from the subwoofer when
YES
is
selected (see notes below). Choose the
PLUS
setting if you want the subwoofer to
output bass sound continuously or you
want deeper bass (the bass frequencies
that would normally come out the front and
center speakers are also routed to the
subwoofer). If you did not connect a
subwoofer choose
NO
(the bass
frequencies are output from other
speakers).
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
If you have a subwoofer and like lots of
bass, it may seem logical to select
LARGE
for your front speakers and
PLUS
for the
subwoofer. This may not, however, yield the
best bass results. Depending on the
speaker placement of your room you may
actually experience a decrease in the
amount of bass due to low frequency
cancellations. In this case, try changing
the position or direction of speakers. If you
can’t get good results, listen to the bass
response with it set to
PLUS
and
YES
or the
front speakers set to
LARGE
and
SMALL
alternatively and let your ears judge which
sounds best. If you’re having problems, the
easiest option is to route all the bass
sounds to the subwoofer by selecting
SMALL
for the front speakers.
Crossover Network
Default setting:
100Hz
This setting decides the cutoff between bass
sounds playing back from the speakers
selected as
LARGE
, or the subwoofer, and bass
sounds playing back from those selected as
SMALL
. It also decides where the cutoff will be
for bass sounds in the LFE channel.
2
1 Select ‘Crossover Network’ from the
Manual SP Setup menu.
2 Choose the frequency cutoff point.
Frequencies below the cutoff point will be sent
to the subwoofer (or
LARGE
speakers).
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Channel Level
Using the channel level settings, you can
adjust the overall balance of your speaker
system, an important factor when setting up a
home theater system.
Note
1• If the surround speakers are set to
NO
, the surround back speakers will automatically be set to
NO
.
• If you selected
Second Zone
or
Front Bi-Amp
(in
Surround back speaker setting
on page 34) you can’t adjust the surround
back settings.
• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.
2 For more on selecting the speaker sizes, see
Speaker Setting
above.
4.Manual SP Setup
:Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
4b.Crossover Network
:Finish
Frequency 80Hz
VSX_816.book.fm 41 ページ 2005年12月8日 木曜日 午後6時54分
The System Setup menu07
42
En
1 Select ‘Channel Level’ from the Manual
SP Setup menu.
2 Select a setup option.
Manual
– Move the test tone manually
from speaker to speaker and adjust
individual channel levels.
Auto
– Adjust channel levels as the test
tone moves from speaker to speaker
automatically.
3 Confirm your selected setup option.
The test tones will start after you press
ENTER
.
After the volume increases to the reference
level, test tones will be output.
4 Adjust the level of each channel using
/
.
If you selected
Manual
, use
/
to switch
speakers. The
Auto
setup will output test tones
in the order shown on-screen:
Adjust the level of each speaker as the test
tone is emitted.
1
5 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
You can change the channel levels at any
time by using
EFFECT/CH SEL
and
+/–
on
the remote control. You can set two
channel levels: one for
DVD 5.1 CH
and
one for the listening modes.
Speaker Distance
For good sound depth and separation from
your system, you need to specify the distance
of your speakers from the listening position.
The receiver can then add the proper delay
needed for effective surround sound.
1 Select ‘Speaker Distance’ from the
Manual SP Setup menu.
2 Adjust the distance of each speaker
using
/
.
You can adjust the distance of each speaker in
0.5 feet increments.
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
For best surround sound, make sure the
surround back speakers are the same
distance from the listening position.
Note
1• If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level
of each speaker to 75 dB SPL (C-weighting/slow reading).
• The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.
4.Manual SP Setup
:Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
4c.Channel Level
Test Tone Manual
ENTER:Next:Cancel
4c.Channel Level
Test Tone [ Manual ]
Please Wait . . . 20
Caution!
Loud test tones
will be output.
:Cancel
4c.Channel Level
L 0.0dB
C [ 0.0dB ]
R [ 0.0dB ]
RS [ 0.0dB ]
SBR [ 0.0dB ]
SBL [ 0.0dB ]
LS [ 0.0dB ]
SW [ 0.0dB ]
:Finish
4.Manual SP Setup
:Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
4d.Speaker Distance
L 10.0ft
C [ 10.0ft ]
R [ 10.0ft ]
RS [ 10.0ft ]
SBR [ 10.0ft ]
SBL [ 10.0ft ]
LS [ 10.0ft ]
SW [ 10.0ft ]
:Finish
VSX_816.book.fm 42 ページ 2005年12月8日 木曜日 午後6時54分
Using the tuner
08
43
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 8:
Using the tuner
Listening to the radio
The following steps show you how to tune in to
FM and AM radio broadcasts using the
automatic (search) and manual (step) tuning
functions. If you already know the frequency of
the station you want, see
Tuning directly to a
station
below. Once you are tuned to a station
you can memorize the frequency for recall
later—see
Saving station presets
on the next
page for more on how to do this.
1 Press FM or AM to select the band.
2 Tune to a station.
There are three ways to do this:
Automatic tuning
To search for stations in the currently
selected band, press and hold
TUNE
/
for about a second. The receiver will start
searching for the next station, stopping
when it has found one. Repeat to search for
other stations.
Manual tuning
To change the frequency one step at a
time, press
TUNE
/
.
High speed tuning
Press and hold
TUNE
/
for high speed
tuning. Release the button at the frequency
you want.
Improving FM stereo sound
If the (tuned) or (stereo) indicators
don't light when tuning to an FM station
because the signal is weak, press the
MPX
button to switch the receiver into mono
reception mode. This should improve the
sound quality and allow you to enjoy the
broadcast.
Tuning directly to a station
Sometimes, you'll already know the frequency
of the station you want to listen to. In this case,
you can simply enter the frequency directly
using the number buttons on the remote
control.
1 Press FM or AM to select the band.
2 Press D.ACCESS (Direct Access).
3 Use the number buttons to enter the
frequency of the radio station.
For example, to tune to
106.00
(FM), press
1
,
0
,
6
,
0
,
0
.
If you make a mistake halfway through, press
D.ACCESS
twice to cancel the frequency and
start over.
Saving station presets
If you often listen to a particular radio station,
it's convenient to have the receiver store the
frequency for easy recall whenever you want to
listen to that station. This saves the effort of
manually tuning in each time. This unit can
ANALOG
AT T
MIDNIGHT/
LOUDNESS
SB ch
DIMMER
SLEEP
SR+
+10
D.ACCESS
CLASS
DISC
ENTER
TV CONTROL
TV DVR
TV CTRL
CD
TUNE
TUNE
ST ST
ENTER
TOP MENU
DTV MENU
T.EDIT
MENU
RETURN
GUIDE
SETUP
CATEGORY
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
RECEIVER
SHIFT
VOL
AUTO SURR
STANDARD ADV.SURR
S.RETRIEVER
SIGNAL SEL
STEREO
INPUT
SELECT
TV CH
MPX
AUDIO
DISP
SUBTITLE
DIALOG E
EFFECT/CH SEL
ACOUSTIC EQ
REC
MUTE
TV VOL
REC STOP JUKEBOX
HDD
CH
CH
DVD
DTV ON/OFF DT V INFO
VSX_816.book.fm 43 ページ 2005年12月8日 木曜日 午後6時54分
Using the tuner08
44
En
memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations
each. When saving an FM frequency, the
MPX
setting (see previous page) is also stored.
1
1 Tune to a station you want to memorize.
See
Listening to the radio
on the previous page
for more on this.
2 Press T.EDIT (TUNER EDIT).
The display shows
ST. MEMORY
, then a
blinking memory class.
3 Press CLASS to select one of the three
classes then press
ST
/
to select the
station preset you want.
You can also use the number buttons or the
MULTI JOG
dial (front panel) to select a station
preset.
4 Press
ENTER
.
After pressing
ENTER
, the preset class and
number stop blinking and the receiver stores
the station.
Naming station presets
For easier identification, you can name your
station presets.
1 Choose the station preset you want to
name.
See
Listening to station presets
below for how
to do this.
2 Press T.EDIT (TUNER EDIT).
The display shows
ST. NAME
, then a blinking
cursor at the first character position.
3 Input the name you want.
Choose a name up to four characters long.
Use the
MULTI JOG
dial (front panel) or the
ST
/
buttons (remote) to select
characters.
Press
ENTER
to confirm a character. If no
character is input, a space is input.
The name is stored when
ENTER
is pressed
after choosing the fourth character.
Tip
To erase a station name, simply repeat
steps 1-3 and input four spaces instead of
a name.
Once you have named a station preset, you
can press
DISP
when listening to a station
to switch the display between name and
frequency.
Listening to station presets
You will need to have some presets stored to do
this. See
Saving station presets
above if you
haven’t done this already.
1 Press FM, then press CLASS to select the
class in which the station is stored.
Press repeatedly to cycle through classes A, B
and C.
2 Press
ST
/
to select the station preset
you want.
You can also use the number buttons on
the remote control to recall the station
preset.
Note
1 If the receiver is left disconnected from the AC power outlet for over a month, the station memories will be lost and will have
to be reprogrammed.
VSX_816.book.fm 44 ページ 2005年12月8日 木曜日 午後6時54分
Making recordings
09
45
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 9:
Making recordings
Making an audio or a video
recording
You can make an audio or a video recording
from the built-in tuner, or from an audio or
video source connected to the receiver (such
as a CD player or TV).
Keep in mind you can’t make a digital
recording from an analog source or vice-versa,
so make sure the components you are
recording to/from are hooked up in the same
way (see Connecting up on page 12 for more on
connections).
If you want to record a video source, you also
need to use the same type of connection for the
source as for the recorder. For example, you
can’t record a component hooked up to S-video
jacks with a recorder hooked up to the
composite video outputs (see page 16 for more
on video connections).
1 Select the source you want to record.
Use the MULTI CONTROL buttons (or INPUT
SELECT).
2 Select the input signal (if necessary).
Press SIGNAL SEL to select the input signal
corresponding to the source component (see
page 33 for more on this).
3 Prepare the source you want to record.
Tune to the radio station, load the CD, video,
DVD etc.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the
recording device and set the recording levels.
Refer to the instructions that came with the
recorder if you are unsure how to do this. Most
video recorders set the audio recording level
automatically—check the component’s
instruction manual if you’re unsure.
5 Start recording, then start playback of the
source component.
1
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
ANALOG
SB h
SLEEP
RECEIVER
SOURCE
INPUT
SELECT
TV DVR
TV CTRL
CD
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
SHIFT
VOL
AUTO SURR
STANDARD ADV.SURR
S.RETRIEVER
SIGNAL SEL
STEREO
INPUT
SELECT
TV
CH
MPX
AUDIO
DISP
SUBTITLE
DIALOG E
EFFECT/CH SEL
ACOUSTIC EQ
REC
MUTE
TV
VOL
REC STOP JUKEBOX
HDD
CH
CH
DVD
DTV ON/OFF DT V INFO
Note
1• The receiver's volume, balance, tone (bass, treble, loudness), and surround effects have no effect on the recorded signal.
• Some digital sources are copy-protected, and can only be recorded in analog.
• Some video sources are copy-protected. These cannot be recorded.
• Recording from XM Radio is not possible.
08_making_recordings.fm 45 ページ 2005年12月14日 水曜日 午後5時32分
Controlling the rest of your system10
46
En
Chapter 10:
Controlling the rest of your
system
Operating other Pioneer
components
Many Pioneer components have SR
CONTROL
jacks which can be used to link components
together so that you can use just the remote
sensor of one component. When you use a
remote control, the control signal is passed
along the chain to the appropriate
component.
1
Note that if you use this feature,
make sure that
you also have at least one set of analog audio or
video jacks connected
to another component
for grounding purposes.
Setting the remote to control
other components
Most components can be assigned to one of
the
MULTI CONTROL
buttons using the
component’s manufacturer preset code stored
in the remote.
However, please note that there are cases
where only certain functions may be
controllable after assigning the proper preset
code, or the codes for the manufacturer in the
remote control will not work for the model that
you are using.
2
Note
You can cancel or exit any of the steps by
pressing
RECEIVER
. To go back a step,
press
RETURN
.
After one minute of inactivity, the remote
automatically exits the operation.
Note
1• If you want to control all your components using this receiver’s remote control, refer to
Controlling the rest of your system
on page 46.
• If you have connected a remote control to the
CONTROL IN
jack (using a mini-plug cable), you won't be able to control this
unit using the remote sensor.
CONTROL
OUT
IN
CONTROL
OUT
IN
Receiver
Remote
control
unit
Other Pioneer products
with CONTROL terminals
Connect to CONTROL
terminal of other
Pioneer products
2• TV codes (for example, codes for TV, CATV, Satellite TV or DTV) can only be assigned to the
TV/SAT
or
TV CTRL
button.
• If you assign the
FM
or
AM
function to another component, you will have to reassign it to the Pioneer preset code to use
this receiver’s built-in tuner.
VSX_816.book.fm 46 ページ 2005年12月8日 木曜日 午後6時54分
Controlling the rest of your system
10
47
En
English
Français
Deutsch
Nederlands
Italiano
Español
Selecting preset codes directly
1 While pressing the RECEIVER button,
press and hold the
SETUP
button.
The remote LCD display shows
SETUP
.
2 Use
/
to select PRESET then press
ENTER
.
3 Press the MULTI CONTROL button for the
component you want to control then press
ENTER
.
The LCD on the remote displays the
component you want to control.
1
4 Use
/
to select the first letter of the
brand name of your component then press
ENTER
.
This should be the manufacturer’s name (for
example,
P
for Pioneer).
5 Use
/
to select the manufacturer’s
name from the list then press
ENTER
.
6 Use
/
to select the proper code from
the list, then try using this remote control
with your component.
The code should start with the component type
(for example,
DVD 009
). If there is more than
one, start with the first one.
To try out the remote control, switch the
component on or off (into standby) by pressing
SOURCE
. If it doesn’t seem to work, select
the next code from the list (if there is one).
7 If your component is controlled
successfully, press
ENTER
to confirm.
The remote LCD display shows
OK
.
Erasing one of the remote
control button settings
This erases a control assigned to one of the
buttons and restores it to the factory default.
1 While pressing the RECEIVER button,
press and hold the
SETUP
button.
The remote LCD display shows
SETUP
.
2 Use
/
to select
ERASE
then press
ENTER
.
3 Press the MULTI CONTROL button
corresponding to the button setting to be
erased then press
ENTER
.
The LCD on the remote displays the
component.
4 Press and hold the button to be erased for
two seconds.
The LCD display shows
OK
or
NO CODE
to
confirm the button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press the RECEIVER button when you’re
done.
Erasing all of the remote control
presets
This will erase all preset remote control preset
codes.
1 While pressing the RECEIVER button,
press and hold the
SETUP
button.
The remote LCD display shows
SETUP
.
2 Use
/
to select
RESET
then press
ENTER
.
Note
1 You can’t assign the
RECEIVER
button.
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
ANALOG
AT T
SB ch
SLEEP
RECEIVER
SOURCE
INPUT
SELECT
TV DVR
TV CTRL
CD
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
MIDNIGHT/
LOUDNESS
DIMMER
SR+
+10
D.ACCESS
CLASS
DISC
ENTER
TV CONTROL
VOL
TUNE
TUNE
ST ST
INPUT
SELECT
TV CH
TV VOL
ENTER
TOP MENU
DTV MENU
T.EDIT
MENU
RETURN
GUIDE
SETUP
CATEGORY
VSX_816.book.fm 47 ページ 2005年12月8日 木曜日 午後6時54分
Controlling the rest of your system10
48
En
3 Press and hold
ENTER for about two
seconds
.
The LCD shows
OK
to confirm the remote
presets have been erased.
Direct function
Default setting:
ON
You can use the direct function feature to
control one component using the remote
control while at the same time, using your
receiver to playback a different component.
This could let you, for example, use the remote
control to set up and listen to a CD on the
receiver and then use the remote control to
rewind a tape in your VCR while you continue
to listen to your CD player.
When direct function is on, any component
you select (using the
MULTI CONTROL
buttons) will be selected by both the receiver
and the remote control. When you turn direct
function off, you can operate the remote
control without affecting the receiver.
1
1 While pressing the RECEIVER button,
press and hold the
SETUP
button.
The remote LCD display shows
SETUP
.
2 Use
/
to select
DIRECT F
then press
ENTER
.
3 Press the MULTI CONTROL button for the
component you want to control
then press
ENTER
.
The LCD on the remote displays the
component you want to control.
4 Use
/
to switch direct function ON or
OFF then press
ENTER
.
The LCD shows
OK
to confirm the setting.
Confirming preset codes
Use this feature to check which preset code is
assigned to a
MULTI CONTROL
button.
1 While pressing the RECEIVER button,
press and hold the
SETUP
button.
The remote LCD display shows
SETUP
.
2 Use
/
to select READ ID then press
ENTER
.
3 Press the MULTI CONTROL button of the
component for which you want to check the
preset code.
The brand name and preset code appears in
the display for three seconds.
Note
1 You can’t use direct function with the
TV CTRL
function.
VSX_816.book.fm 48 ページ 2005年12月8日 木曜日 午後6時54分
Controlling the rest of your system
10
49
En
English
Français
Deutsch
Nederlands
Italiano
Español
Controls for TVs
This remote control can control components after entering the proper codes or teaching the
receiver the commands (see
Operating other Pioneer components
on page 46 for more on this).
Use the
MULTI CONTROL
buttons to select the component
The
TV CONTROL
buttons on the remote control are dedicated to control the TV assigned to
the
TV CTRL
button. If you have two TVs, assign the main TV to the
TV CTRL
button.
Button(s)
Function Components
TV
Switches the DTV on or off. DTV
Switches the TV or CATV between standby and on. Cable TV/Satellite TV/TV
INPUT
SELECT
Switches the TV input. (Not possible with all models.) TV
TV CH +/–
Selects channels. Cable TV/Satellite TV/TV/
DTV
TV VOL +/–
Adjust the TV volume. Cable TV/Satellite TV/TV/
DTV
SOURCE
Press to switch the component assigned to the
TV CTRL
button on or off.
Cable TV/Satellite TV/TV/
DTV
Switches the DTV on or off. DTV
Press to get information on DTV programs. DTV
Use to choose the BLUE commands on a DTV menu. DTV
Use to choose the YELLOW commands on a DTV menu. DTV
Use to choose the GREEN commands on a DTV menu. DTV
Use to choose the RED commands on a DTV menu. DTV
AUDIO
Use to switch DTV audio tracks. DTV
DTV MENU
Press to display the DTV menu. DTV
GUIDE
Use as the
GUIDE
button for navigating. Cable TV/Satellite TV/TV/
DTV
RETURN
Use to select closed captioning with DTV. DTV
Number
Buttons
Use to select a specific TV channel. Cable TV/Satellite TV/TV/
DTV
+10
button Use to add a decimal points when selecting TV channels. DTV
ENTER
/
DISC
Use to enter a channel. Cable TV/Satellite TV/TV/
DTV
VSX_816.book.fm 49 ページ 2005年12月8日 木曜日 午後6時54分
Controlling the rest of your system10
50
En
Controls for other components
This remote control can control these components after entering the proper codes or teaching the
receiver the commands (see
Operating other Pioneer components
on page 46 for more on this).
Use the
MULTI CONTROL
buttons to select the component.
MENU
Select different menus from the DTV functions. DTV
Select the menu screen. Cable TV/Satellite TV/TV

&
ENTER
Press to select or adjust and navigate items on the menu
screen.
Cable TV/Satellite TV/TV/
DTV
Button (s)
Function Components
SOURCE
Press to switch the component between standby and on. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
Press to return to the start of the current track.
Repeated presses skips to the start of previous tracks.
CD/MD/CD-R/DVD/LD
player
Go back channels (channel –). DVR/VCR
Press to advance to the start of the next track.
Repeated presses skips to the start of following tracks.
CD/MD/CD-R/DVD/LD
player
Go forward channels (channel +). VCR
Pause playback or recording. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
Start playback. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
Hold down for fast forward playback. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
Hold down for fast reverse playback. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
Stops playback (on some models, pressing this when the
disc is already stopped will cause the disc tray to open).
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
ì
REC
(
SHIFT+
)
Starts recording. To prevent accidental recording, this
button must be pressed twice to take effect.
MD/CD-R/VCR/ DVR player/
Cassette deck
REC STOP
(
SHIFT+
)
Stops recording. DVR player
Button(s)
Function Components
VSX_816.book.fm 50 ページ 2005年12月8日 木曜日 午後6時54分
Controlling the rest of your system
10
51
En
English
Français
Deutsch
Nederlands
Italiano
Español
JUKEBOX
(
SHIFT+
)
Switches to the Jukebox feature. DVR player
Number
buttons
Directly access tracks on a program source. CD/MD/CD-R/VCR/LD
player
Use the number buttons to navigate the on-screen display. DVD/DVR player
+10
button Selects tracks higher than 10. (For example, press
+10
then
3
to select track 13.)
CD/MD/CD-R/VCR/LD
player
ENTER
/
DISC
Chooses the disc. Multiple CD player
Ejects the disc. MD player
Use as the
ENTER
button.
VCR
Use as the
CLEAR
button. DVD
Displays the setup screen for DVR players. DVR player
Changes sides of the LD. LD player
TOP MENU
Displays the disc ‘top’ menu of a DVD player. DVD/DVR player
MENU
Displays menus for the current DVD or DVR you are using. DVD/DVR player
Pauses the tape. Cassette deck
Stops the tape. Cassette deck
ENTER
Starts playback. Cassette deck
/
Fast rewinds/fast forwards the tape. Cassette deck

&
ENTER
Navigates DVD menu/options. DVD/DVR Player
GUIDE
Press to access the DVD player setup screen. DVD/DVR Player
CH +/–
Selects channels. VCR/DVD/DVR Player
Selects tracks. CD/MD/CD-R/
Cassette deck
AUDIO
Changes the audio language or channel. DVD/DVR Player
SUBTITLE
Displays/changes the subtitles on multilingual DVDs. DVD/DVR Player
HDD
(SHIFT
+ CH–)
Switches to the hard disk controls when using a DVD/
HDD recorder.
DVR Player
DVD
(SHIFT
+ CH+)
Switches to the DVD controls when using a DVD/HDD
recorder.
DVR Player
Button (s)
Function Components
VSX_816.book.fm 51 ページ 2005年12月8日 木曜日 午後6時54分
Other connections11
52
En
Chapter 11:
Other connections
Caution
Before making or changing the connections
,
switch off the power and disconnect the
power cord from the power outlet.
Plugging in components should be the last
connection you make with your system.
Do not allow any contact between speaker
wires from different terminals.
You can use speakers with a nominal
impedance between 6–16
(please see
Switching the speaker impedance
on
page 63 if you plan to use speakers with an
impedance of less than 8
).
Using XM Radio
XM is the leading provider of satellite radio
service in the United States. Through two high-
power satellites,
Rock
and
Roll
, XM Radio
service offers over 150 channels of music,
news, talk, sports and children's programming
on a monthly subscription basis. XM Radio
offers consumers clear sound quality from
digital signal radios, an extensive variety of
programming and nationwide coverage. Visit
www.xmradio.com for more details on this
service.
Connecting your XM Radio receiver
After purchasing a Connect-and-Play™
antenna (sold separately), you will also need to
activate the XM Radio digital radio service to
receive broadcasts.
1
1 Connect an XM Radio Connect-and-Play™
antenna to the XM Radio jack on the rear of
this receiver.
You will also need to activate the XM Radio
service.
2 Press
XM RADIO (SHIFT+AM)
to switch
to the XM RADIO input.
For best reception, you may need to move the
Connect-and-Play™ antenna near a window
(the southernmost window should produce the
best results).
If after pressing
XM RADIO
the display
shows
Check Antenna
, try disconnecting
the antenna and reconnecting.
Note
1 Hardware and required basic monthly subscription sold separately. Premium Channel available at additional monthly cost.
Installation costs and other fees and taxes, including a one-time activation fee may apply. Subscription fee is consumer only. All
fees and programming subject to change. Channels with frequent explicit language are indicated with an XL. Channel blocking
is available for XM radio receivers by calling 1-800-XMRADIO. Subscriptions subject to Customer Agreement available at xmra-
dio.com. Only available in the 48 contiguous United States.
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/ VCR
)
COAX
(
DVD/LD
)
1
2
ASSIGNABLE
DIGITAL IN
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
Connect-and-Play antenna
This receiver
VSX_816.book.fm 52 ページ 2005年12月8日 木曜日 午後6時54分
Other connections
11
53
En
English
Français
Deutsch
Nederlands
Italiano
Español
Listening to XM Radio
After connecting, you will be able to use this
receiver to select channels and navigate
categories using the on-screen display.
1
The
information displayed is as follows:
Selecting channels and browsing by
genre
From the XM Channel Guide, you can browse XM
Radio channels in the order that they appear, or
you can narrow your channel search by genre.
Use
/
to display the XM Channel
Guide screen, then use the
///
buttons followed by
ENTER
to select a
channel to listen to the XM radio broadcast.
To browse by genre, first press
CATEGORY , use /// to select a
genre then press ENTER.
2
To cancel and exit any time, press
RETURN.
Tip
You can select channels directly by
pressing D.ACCESS then the three-digit
channel number.
You can press DISP to change XM Radio
information in the front panel display.
The currently selected channel is
automatically chosen (without pressing
ENTER) after 5 seconds.
Using XM Surround
XM Surround uses Neural Surround™
technology to achieve optimal surround sound
from XM radio.
While listening to XM Radio, press
AUTO SURR for XM Surround listening.
See About Neural Surround™ below for more
on this.
About Neural Surround™
Neural Surround™ represents the latest
advancement in surround technology and has
been adopted by XM Satellite Radio for digital
radio broadcasts of surround recordings and
live events.
Neural Surround™ employs psychoacoustic
frequency domain processing which allows
delivery of a more detailed sound stage with
superior localization of surround elements.
System playback is scalable from stereo up to
state-of-the-art multichannel surround.
Neural Surround™ is trademark owned by
Neural Audio Corporation.
Saving channel presets
This receiver can memorize up to 30 channels,
stored in three banks, or classes, (A, B and C)
of 10 stations each.
1 Select the channel you want to memorize.
See Selecting channels and browsing by genre
above.
2 Press
T.EDIT
.
The display shows a blinking memory class.
Note
1 It’s easiest if you have your TV switched on to take advantage of the OSDs. You can, however, use just the front panel display
to do everything if you prefer.
2 Select XM000 (RADIO ID) from the on-screen display to check the Radio ID of the Connect-and-Play antenna.
XM Satellite Radio A
Decades
A0
Fifties (50's) XM005
Remy Sherman
Lovin' You
Preset class
Signal strength
Category
Preset number
Channel number
Artist name
Song name
Channel name
XM Satellite Radio A
Decades
A0
Fifties (50's) XM005
Remy Sherman
Lovin' You
XM Channel Guide
Previous
[
000 RADIO ID
]
[
001 Preview
]
[
002 Highway1
]
[
003 America
]
[
004 Hank's Place
]
[
005 Fifties (50's)
]
[
006 Sixties (60's)
]
[
007 Seventies (70's)
]
Next
: Exit
10_Other_connections.fm 53 ページ 2005年12月9日 金曜日 午前11時8分
Other connections11
54
En
3 Press CLASS to select one of the three
classes then press
/
to select the channel
preset you want.
You can also use the number buttons to select
a preset.
The default for all presets is
XM001
.
4 Press
ENTER
.
After pressing
ENTER
, the preset class and
number stop blinking and the receiver stores
the XM channel.
Listening to channel presets
You will need to have some presets stored to do
this.
1 Press CLASS to select the class in which
the channel is stored.
Press repeatedly to cycle through classes A, B
and C.
2 Press
/
to select the channel preset
you want.
You can also use the number buttons on
the remote control to recall the channel
preset.
Connect & Play™, XM-Ready
®
and The Ultimate
Playlist are trademarks of XM Satellite Radio Inc.
©2005 XM Satellite Radio Inc. All rights reserved.
All other trademarks are the property of their
respective owners.
Second Zone speaker B setup
After selecting
Second Zone
in
Surround back
speaker setting
on page 34, you can use the
speakers connected to the (surround back) B
speaker terminals on the rear panel to listen to
stereo playback in another room. See
Switching the speaker system
below for the
listening options with this setup.
1 Connect a pair of speakers to the
surround back speaker terminals on the rear
panel.
Connect them the same way you connected
your speakers in
Connecting the speakers
on
page 19. Make sure to review
Hints on speaker
placement
on page 20 when placing the
speakers in another room.
2 Select ‘
Second Zone’
from the ‘
Surr Back
System’
menu.
See
Surround back speaker setting
on page 34
to do this.
Switching the speaker system
If you selected
Second Zone
in
Surround back
speaker setting
on page 34, three speaker
system settings are possible using the
SPEAKERS
button. If you selected
Normal (SB)
or
Front Bi-Amp
, the speaker system is fixed
as
SP
A
or
SP
AB
(respectively). The options
below are for the
Second Zone
setting only.
1
Use the SPEAKERS button on the front
panel to select a speaker system setting.
Press repeatedly to choose a speaker system
option:
SP
A
– Sound is output from the speakers
connected to the A speaker terminals
(multichannel playback is possible).
SP
B
– Sound is output from the two
speakers connected to speaker system B
(only stereo playback is possible).
Note
1• The subwoofer output depends on the settings you made in
Speaker Setting
on page 40. However, if
SP
B
is selected above,
no sound is heard from the subwoofer (the LFE channel is not downmixed).
• Depending on the
Surround back speaker setting
on page 34 output from the surround back pre-out terminals may change.
• All speaker systems (except
Second Zone
connections) are switched off when headphones are connected.
MIDNIGHT/
LOUDNESS
QUICK
SETUP
SETUP
RETURN
TUNING/
STATION
TONE
ANALOG
ATT
SPEAKERS
TUNER
EDIT
DIMMER
MULTI JOG
VSX_816.book.fm 54 ページ 2005年12月8日 木曜日 午後6時54分
Other connections
11
55
En
English
Français
Deutsch
Nederlands
Italiano
Español
SP
AB
– Sound is output from speaker
system A (up to 5 channels, depending on
the source), the two speakers in speaker
system B, and the subwoofer.
Multichannel sources (heard through
speaker system A) are downmixed for
stereo output from speaker system B.
Bi-amping your front speakers
Bi-amping is when you connect the high
frequency driver and low frequency driver of
your speakers to different amplifiers (in this
case, to both front and surround back
terminals) for better crossover performance.
Your speakers must be bi-ampable to do this
(having separate terminals for high and low)
and the sound improvement will depend on the
kind of speakers you’re using.
1 Connect your speakers as shown below.
This illustration below shows the connections
for bi-amping your front left speaker. Hook up
your front right speaker in the same way.
Since both front and surround back speaker
terminals output the same audio, it doesn’t
matter which set (front or surround back) is
powering which part (
Hi
or
Low
) of the
speaker.
Make sure that the
+
/
connections are
properly inserted.
2 Select the
’Front Bi-Amp’
setting from
the ‘
Surr Back System’
menu.
See
Surround back speaker setting
on page 34
to specify how you’re using the surround back
speaker terminals.
Caution
Most speakers with both
Hi
and
Low
terminals have two metal plates that
connect the
Hi
to the
Low
terminals. These
must be removed when you are bi-amping
the speakers or you could severely damage
the amplifier. See your speaker manual for
more information.
If your speakers have a removable
crossover network, make sure you do not
remove it for bi-amping. Doing so may
damage your speakers.
Bi-wiring your speakers
The reasons for bi-wiring are basically the
same as bi-amping, but additionally,
interference effects within the wire could be
reduced, producing better sound. Again, to do
this your speakers must be bi-wireable (that is
they must have separate terminals for the high
and low frequencies). When bi-wiring, make
sure you’ve selected
Normal (SB)
or
Second
Zone
in
Surround back speaker setting
on
page 34.
To bi-wire a speaker, connect two speaker
cords to the speaker terminal on the receiver.
Using a banana plug for the second
connection is recommended.
FRONT
R L
CENTERSURROUND
S
P
E
A
K
E
R
S
R
L
SURROUND BACK
A B
LR
Hi
Lo
Front left
speaker
VSX_816.book.fm 55 ページ 2005年12月8日 木曜日 午後6時54分
Other connections11
56
En
Caution
Make sure you use a parallel (not series,
which are fairly uncommon) connection
when bi-wiring your speakers.
Don't connect different speakers from the
same terminal in this way.
Connecting additional
amplifiers
This receiver has more than enough power for
any home use, but it’s possible to add
additional amplifiers to every channel of your
system using the pre-outs. Make the
connections shown below to add amplifiers to
power your speakers.
1
Before making or changing the
connections, switch off the power and
disconnect the power cord from the AC
outlet.
Using this receiver with a
Pioneer plasma display
If you have a Pioneer plasma display
2
, you can
use an SR+ cable to connect it to this unit and
take advantage of various convenient features,
such as automatic video input switching of the
plasma display when the input is changed.
Note
1• You can use the additional amplifier on the surround back channel pre-outs for a single speaker as well. In this case plug
the amplifier into the left (
L (Single)
) terminal only.
• The sound you hear from the surround back terminals depends on the
Surround back speaker setting
on page 34.
• To hear sound only from the pre-outs, simply disconnect any speakers that are connected directly to the receiver.
• If you’re not using a subwoofer, change the front speaker setting (see
Speaker Setting
on page 40) to large.
(
DVD/LD
)
IN
CENTER
PB
PR
(
TV/SAT
)
IN
FRONT SURROUND SURROUND
BACK
1
2
SURROUND BACK
B
L
L
RRR
CENTER
LL
R
PREOUT
INPUT
L R
ANALOG
INPUT
L R
ANALOG
INPUT
L R
ANALOG
INPUT
ANALOG
INPUT
ANALOG
Front channel
amplifier
Surround channel
amplifier
Surround back
channel amplifier
Center channel
amplifier (mono)
Powered
subwoofer
To SUB WOOFER PREOUT jack
2 This receiver is compatible with all Pioneer plasma displays from 2003 onward.
COAX
OPT
OPT
(
CD
)
XM
IN
ASSIGNABLE
DIGITAL IN
1
2
(
DVR/ VCR
)
COAX
(
DVD/LD
)
1
2
ASSIGNABLE
DIGITAL IN
(
TV/ SAT
)
AM
LOOP
FM UNBAL
75
IN
IN
IN
IN
IN
IN
MONITOR
OUT
MONITOR OUT
OUT
VIDEO
S-VIDEO
SUB
WOOFER
IN
IN
IN
IN
OUT
OUT
OUT
IN
CD
DVR /
VCR
DVR /
VCR
TV /
SAT
TV /
SAT
DVD
/LD
DVD
/LD
PLAY
CD-R
/TAPE
/MD
FRONT
PREOUT
REC
ANTENNA
CONTROL
D V D
5.1CH
INPUT
AUDIO
R
L
IN
AUX
OUT
IN
OUT
CONTROL
Pioneer plasma
display
This receiver
VSX_816.book.fm 56 ページ 2005年12月8日 木曜日 午後6時54分
Other connections
11
57
En
English
Français
Deutsch
Nederlands
Italiano
Español
Use a 3-ringed miniplug SR+ cable
1
to
connect the
CONTROL IN
jack of this receiver
with the
CONTROL OUT
of your plasma
display.
Before you can use the extra SR+ features, you
need to make a few settings in the receiver. See
SR+ Setup for Pioneer plasma displays
on
page 60 for detailed instructions.
To make the most of the SR+ features, you
should connect your source components (DVD
player, etc.) in a slightly different way to that
described in this chapter. For each
component, connect the video output directly
to the plasma display, and just connect the
audio (analog and/or digital) to this receiver.
Using the SR+ mode with a Pioneer
plasma display
When connected using an SR+ cable, a
number of features become available to make
using this receiver with your Pioneer plasma
display even easier. These features include:
On-screen volume display.
On-screen display of listening mode.
Automatic video input switching on the
plasma display.
Automatic volume muting on the plasma
display.
2
See also
SR+ Setup for Pioneer plasma displays
on page 60 for more on setting up the receiver.
1 Make sure that the plasma display and
this receiver are switched on and that they
are connected with the SR+ cable.
See
Using this receiver with a Pioneer plasma
display
above for more on this.
2 To switch SR+ mode on/off, press
RECEIVER
, then the SR+ button.
The front panel display shows
SR+ ON
or
OFF
.
Note
1• The 3-ringed SR+ cable from Pioneer is commercially available under the part number ADE7095. Contact the Pioneer Cus-
tomer Support division for more information on obtaining an SR+ cable (you can also use a commercially available 3-ringed
mini phone plug for the connection).
• If you connect to a Pioneer plasma display using an SR+ cable, you will need to point the remote control at the plasma dis-
play remote sensor to control the receiver. In this case, you won’t be able to control the receiver using the remote control if you
switch the plasma display off.
DVD player
This receiver
Pioneer plasma
display
Satellite receiver, etc
VIDEO
INPUT 1
VIDEO
INPUT 2
TV/SAT
AUDIO IN
DVD
AUDIO IN
UPDOWN
MULTI JOG
MASTER
VOLUME
ENTER
AUDIO /V IDE O MULTI-CHANNEL
RECEIVER
VSX
-
816
STANDBY/ON
PHONES
DVD/LD
TV/SAT DVR/VCR VIDEO
CD
CD
-
R/TAPE/MD FM
AM
STANDARD
MIDNIGHT/
LOUDNESS
ADVANCED
SURR
ST/DIRECT/
AUTO SURR
LISTENING
MODE
QUICK
SETUP
SETUP
RETURN
TUNING/
STATION
TONE
ANALOG
ATT
SPEAKERS
TUNER
EDIT
DIMMER
MULTI JOG
XM
MCACC
SETUP MICDIGITAL INAUDIO RLVIDEO
VIDEO
INPUT
S
-
VIDEO
AUX
SIGNAL
SELECT
SB
ch
PROCESSING
ACOUSTIC
EQ
DIGITAL PRECISION
PROCESSING
DIGITAL PRECISION
PROCESSING
2 The automatic volume muting feature is enabled separately; see
SR+ Setup for Pioneer plasma displays
on page 60.
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
RECEIVER
SOURCE
INPUT
SELECT
TV DVR
TV CTRL
CD
DVD
FM AM
RECEIVER
CD-R/TAPE
XM RADIO
ANALOG
AT T
MIDNIGHT/
LOUDNESS
SB ch
DIMMER
SLEEP
SR+
+10
D.ACCESS
CLASS
DISC
ENTER
TUNE
ST ST
ENTER
TOP MENU
DTV MENU
T.EDIT
MENU
VSX_816.book.fm 57 ページ 2005年12月8日 木曜日 午後6時54分
Other Settings12
58
En
Chapter 12:
Other Settings
The Input Assign menu
You only need to make settings in the Input
Assign menu if you didn’t hook up your digital
equipment according to the default settings for
the digital inputs, or if you have connected
equipment using component video cables.
1 Press
RECEIVER
on the remote control,
then press the
SETUP
button.
An on-screen display (OSD) appears on your
TV. Use /// and ENTER on the remote
control to navigate through the screens and
select menu items. Press RETURN to confirm
and exit the current menu.
2 Select ‘Input Assign’ from the System
Setup menu.
Assigning the digital inputs
Default settings:
Coaxial - 1 DVD
Coaxial - 2 DVR
Optical - 1 CD
Optical - 2 TV
You only need to do this if you didn’t hook up
your digital equipment according to the default
settings for the digital inputs (see above). This
setting tells the receiver what digital
equipment is hooked up to which terminal so
the buttons on the remote correspond to what
you have hooked up.
1 Select ‘Digital Input’ from the Input
Assign menu.
2
Select the number of the digital input to
which you’ve connected the digital component.
The numbers correspond with the numbers
beside the inputs on the back of the receiver.
3 Select the component that corresponds
with the one you connected to that input.
Select between DVD, TV, CD, CD-R, DVR or
OFF.
Use / and ENTER to do this.
If you assign a digital input to a certain
function (for example, DVD/LD) then any
digital inputs previously assigned to that
function will automatically be switched off.
4 When you're finished, press RETURN.
You return to the Input Assign menu.
Assigning the component video inputs
Default settings:
Component 1DVD
Component 2TV
Component 3DVR
If you used component video cords to connect
your video equipment you must tell the receiver
which device it is, or else you may see the S-
video or composite video input instead of the
component video signal. For more on this, see
Using the component video jacks on page 17.
1 Select ‘Component Input’ from the Input
Assign menu.
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
5.Input Assign
:Return
a.Digital Input
b.Component Input
5.Input Assign
:Return
a.Digital Input
b.Component Input
5a.Digital Input Setup
:Finish
Coaxial - 1 DVD
Coaxial - 2 [ DVR ]
Optical - 1 [ CD ]
Optical - 2 [ TV ]
5. Input Assign
:Return
a.Digital Input
b.Component Input
5b.Component Input
:Finish
Component - 1 DVD
Component - 2 [ TV ]
Component - 3 [ DVR ]
11_other_settings.fm 58 ページ 2005年12月9日 金曜日 午前10時30分
Other Settings
12
59
En
English
Français
Deutsch
Nederlands
Italiano
Español
2 Select the number of the component
video input to which you’ve connected your
video component.
The numbers correspond with the numbers
beside the inputs on the back of the receiver.
3 Select the component that corresponds
with the one you connected to that input.
Select between
DVD
,
TV
,
DVR
or
OFF
.
Use
/
and
ENTER
to do this.
Make sure you have connected the audio
from the component to the corresponding
inputs on the rear of the receiver.
If you connect any source component to
the receiver using a component video
input, you should also have your TV
connected to this receiver's component
video
MONITOR
output.
4 When you're finished, press RETURN.
You return to the Input Assign menu.
The Other Setup menu
The Other Setup menu is where you can make
customized settings to reflect how you are
using the receiver.
1 Press
RECEIVER
on the remote control,
then press the
SETUP
button.
An on-screen display (OSD) appears on your
TV. Use
///
and
ENTER
on the remote
control to navigate through the screens and
select menu items. Press
RETURN
to confirm
and exit the current menu.
2 Select ‘Other Setup’ then press
ENTER
.
3 Select the setting you want to adjust.
If you are doing this for the first time, you may
want to adjust these settings in order:
DRC Setup
– Specify the amount of
dynamic range adjustment to Dolby Digital
soundtracks (see
Dynamic Range Control
Setup
below).
Dual Mono Setup
– Isolate one channel
when listening to discs with dual mono
encoding (see
Dual Mono Setup
below).
LFE ATT Setup
– Choose the attenuator
level for the LFE channel (
LFE Attenuator
Setup
on page 60).
SR+ Setup
– Specify how you want to
control your Pioneer plasma display (
SR+
Setup for Pioneer plasma displays
on
page 60).
4 Make the adjustments necessary for each
setting, pressing RETURN to confirm after
each screen.
Dynamic Range Control Setup
Default setting:
OFF
This setting specifies the amount of dynamic
range adjustment to Dolby Digital and DTS
movie soundtracks. You may want to use this
when listening to surround sound at low
volumes.
1 Select ‘DRC Setup’ from the Other Setup
menu.
2 Choose the setting that you want.
MAX
– Dynamic range is reduced (loud
sounds are reduced in volume while
quieter sounds are increased).
MID
– Mid setting.
OFF
– No dynamic range adjustment (use
when listening at higher volume).
3 When you're finished, press
RETURN
.
You return to the Other Setup menu.
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
DRC OFF
6a.Dynamic Range Control
:Finish
VSX_816.book.fm 59 ページ 2005年12月8日 木曜日 午後6時54分
Other Settings12
60
En
Dual Mono Setup
Default setting: CH1
You can specify how dual mono encoded Dolby
Digital and DTS soundtracks should be played.
Dual mono is not widely used, but is
sometimes necessary when two languages
need to be sent to separate channels.
1 Select ‘Dual Mono Setup’ from the Other
Setup menu.
2 Choose the setting that you want.
CH2 – Only channel 2 is played
CH1 CH2 – Both channels are played
through the front speakers
CH1 – Only channel 1 is played
3 When you're finished, press
RETURN
.
You return to the Other Setup menu.
LFE Attenuator Setup
Default setting: ATT 0 dB
Some Dolby Digital and DTS audio sources
include ultra-low bass tones. Set the LFE atten-
uator as necessary to prevent the ultra-low
bass tones from distorting the sound from the
speakers.
1 Select ‘LFE ATT Setup’ from the Other
Setup menu.
2 Choose the setting that you want.
ATT 0dB – No limiting (recommended)
ATT 10dB – 10dB of limiting
LFE OFF – No sound from LFE channel
3 When you're finished, press
RETURN
.
You return to the Other Setup menu.
SR+ Setup for Pioneer plasma displays
Make the following settings if you have
connected a Pioneer plasma display to this
receiver using an SR+ cable. Note that the
number of settings available will depend on the
plasma display you’ve connected.
See also Using this receiver with a Pioneer
plasma display on page 56.
1 Select ‘SR+ Setup’ from the Other Setup menu.
2 Select the ‘PDP Volume Control’ setting
you want.
OFF – The receiver does not control the
volume of the plasma display
ON – When the receiver is switched to one
of the inputs that use the plasma display
(DVD/LD, or another function below), the
volume on the plasma display is muted so
only sound from the receiver is heard.
3 Assign any input source connected to the
plasma display to the corresponding input
number.
This matches the receiver’s input source with a
numbered video input on the plasma display.
For example, assign DVD/LD to input-2 if you
have connected your DVD video output to video
input 2 on the plasma display.
The Monitor Out Connect should be set
to the input that you’ve used to connect
this receiver to your plasma display.
4 When you're finished, press
RETURN
.
You return to the Other Setup menu.
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
Dual Mono [ CH1
6b.Dual Mono Setup
:Finish
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
LFE ATT ATT 0dB
6c. LFE ATT Setup
:Finish
6.Other Setup
:Return
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR
+
Setup
PDP Volume Control
OFF
PDP Input Select
DVD/LD [ input-1 ]
TV/SAT [ input-2 ]
DVR [ input-3 ]
VIDEO [ TV ]
Monitor Out Connect
[ Off ]
6d.SR
+
Setup
:Finish
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-1
TV/SAT input-2
DVR input-3
VIDEO TV
6d.SR
+
Setup
:Finish
[ ]
[ ]
[ ]
Monitor Out Connect
[ Off ]
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-2
TV/SAT OFF
DVR input-3
VIDEO TV
6d.SR
+
Setup
:Finish
[ ]
[ ]
[ ]
Monitor Out Connect
[ Off ]
11_other_settings.fm 60 ページ 2005年12月9日 金曜日 午前10時42分
Additional information
13
61
En
English
Français
Deutsch
Nederlands
Italiano
Español
Chapter 13:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Take a look at the other
components and electrical appliances being used, because sometimes the problem may lie there.
If the trouble isn’t sorted out even after going through the checks below, ask your nearest Pioneer
authorized independent service company to carry out repair work.
If the unit does not operate normally due to external effects such as static electricity disconnect
the power plug from the outlet and insert again to return to normal operating conditions.
Problem Remedy
The power does not turn on. • Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching the rear panel. This
could cause the receiver to shut off automatically.
The receiver suddenly switches
off and the power indicator
blinks.
• After about a minute (you won't be able to switch the unit on during this time),
switch the receiver back on. If the message persists, call a Pioneer authorized
independent service company.
No sound is output when a
function is selected.
• Make sure the component is connected correctly (refer to Connecting up on
page 12).
• Press MUTE on the remote control to turn muting off.
• Press SPEAKERS to select the proper speaker set (see Switching the speaker
system on page 54).
• Press SIGNAL SELECT to select the proper input signal (see Choosing the input
signal on page 33).
No image is output when a
function is selected.
• Make sure the component is connected correctly (refer to Connecting up on page 12).
• Select the correct component (use the input select buttons).
• Check Assigning the component video inputs on page 58 to make sure you’re
assigned the correct input.
• The video input selected on the TV monitor is incorrect. Refer to the instruction
manual supplied with the TV.
No sound from subwoofer. • Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have an LFE channel.
• Switch the subwoofer setting in Speaker Setting on page 40 to YES or PLUS.
• Switch the LFE Attenuator Setup on page 60 to LFEATT 0 or LFEATT 10.
No sound from surround or
center speakers.
• Connect the speakers properly (refer to page 19).
• Refer to Speaker Setting on page 40 to check the speaker settings.
• Refer to Channel Level on page 41 to check the speaker levels.
No sound from surround back
speakers.
• Refer to Speaker Setting on page 40 to check the surround back speaker settings.
• Refer to Channel Level on page 41 to check the speaker levels.
• Refer to Using surround back channel processing on page 31 to make sure
surround back processing and the sound mode are set for surround back sound.
12_additional_info.fm 61 ページ 2005年12月14日 水曜日 午後5時43分
Additional information13
62
En
Considerable noise in radio
broadcasts.
• Connect the antenna (page 18) and adjust the position for best reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and secure to a wall
(or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 18).
• Turn off equipment causing interference or move it away from the receiver (or
move antennas farther away from equipment causing noise).
Broadcast stations cannot be
selected automatically.
• Connect an outdoor antenna (refer to page 18).
Noise during playback of a
cassette deck.
• Move the cassette deck away from your receiver, until the noise disappears.
Sound is produced from other
components, but not from LD
or DVD player.
• Set the
SIGNAL SELECT
to
AUTO
,
DIGITAL
or
ANALOG
according to the type of
connections made. (refer to page 33).
• Set the digital input settings correctly (refer to page 58).
• Make digital connections (refer to page 13) and set the
SIGNAL SELECT
to
DIGITAL
(refer to page 33).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral position.
• Make sure the player's settings are correct and/or the DTS signal out is on. Refer
to the instruction manual supplied with the DVD player.
• Set the input signal type to
DIGITAL
(see
Choosing the input signal
on page 33)
During a playback search,
noise is output from a DTS
compatible CD player.
• This is not a malfunction, but be sure to turn the volume down to prevent the
output of loud noise from your speakers.
Everything seems to be set up
correctly, but the playback
sound is odd.
Check that the positive/negative speaker terminals on the receiver are matched with
the corresponding terminals on the speakers (see
Connecting the speakers
on
page 19).
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• See
Automatically setting up for surround sound (MCACC)
on page 9 to set up your
system again using MCACC (this will automatically compensate for a delay in the
subwoofer output).
After using the Auto MCACC
Setup, the speaker size setting
(
LARGE
or
SMALL
) is incorrect.
• Low-frequency noise could have been caused by an air conditioner or motor.
Switch off all appliances in the room and rerun the Auto MCACC Setup.
Can’t operate the remote
control.
• Replace the batteries (refer to page 6).
• Operate within 23 ft. (7 m), 30° of the remote sensor (refer to page 27).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
• Unplug anything connected to the
CONTROL IN
jack and use remote normally
(see
Operating other Pioneer components
on page 46).
The SR cable is connected, but
the connected components
can’t be operated with the
remote.
• Reinsert the SR cable, making sure it’s connected to the right jack (see
Using this
receiver with a Pioneer plasma display
on page 56).
• Make sure an analog connection has been made between the units.
• This feature only works with Pioneer products.
The display is dark or off. • Press
DIMMER
on the control repeatedly to return to the default.
The
System Setup
screen
doesn't appear.
• When the receiver is in standby, switch to
BURST.OFF
by holding down
ACOUSTIC
EQ
(front panel) and pressing
STANDBY/ON
(the current setting is displayed).
Problem
Remedy
12_additional_info.fm 62 ページ 2005年12月14日 水曜日 午後5時43分
Additional information
13
63
En
English
Français
Deutsch
Nederlands
Italiano
Español
XM radio messages
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1 Switch the receiver into standby.
2 While holding down the TONE button,
press and hold the
STANDBY/ON button for
about three seconds.
3 When you see RESET? appear in the
display, press
ENTER
.
OK?
shows in the display.
4 Press
SETUP
to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory settings.
Switching the speaker
impedance
We recommend using speakers of 8
with this
system, but it is possible to switch the
impedance setting if you plan to use speakers
with a 6
impedance rating.
With the receiver in standby, press
STANDBY/ON
while holding down the
SPEAKERS
button.
Each time you do this, you switch between the
impedance settings:
SP 6 OHM
– Use this setting if your
speakers are rated at 6
.
SP 8 OHM
– Use this setting if your
speakers are rated at 8
or more.
Symptom Cause Action
Check Antenna
The XM antenna is not connected. Check that the XM antenna cable is attached
securely.
XM ANT ERR
A short-circuit occurring in the antenna or
surrounding antenna cable.
Make sure that there is nothing unusual with the
antenna or antenna cable. Switch the power off
then back on again.
Updating
The radio is being updated with the latest
encryption code.
Wait until the encryption code has been
updated. Channels 00 and 01 should function
normally.
No Signal
The XM signal is too weak at the current location.
n/a
Loading
The receiver is acquiring audio or program
information.
Wait until the information has been received.
Off Air
The channel currently selected has stopped
broadcasting.
Select another channel.
CH– – –
You have selected a channel that does not exist,
or that you have not subscribed to.
The receiver will automatically switch to channel
001 (or the last selected channel).
– – – – – – – –
There is no artist name/feature, song/program
title, or channel category associated with the
channel at this time.
No action needed.
VSX_816.book.fm 63 ページ 2005年12月8日 木曜日 午後6時54分
Additional information13
64
En
Specifications
Amplifier section
Continuous power output (stereo)
Front. . 110 W (20 to 20 000 Hz, THD 0.7 %, 8
)
1
Continuous power output (surround)
Front. . . . . 110 W per channel (1 kHz, 1.0 %, 8
)
Center . . . . . . . . . . . . . .110 W (1 kHz, 1.0 %, 8
)
Surround . . . . . . . . . . . . . . . . . 110 W per channel
(1 kHz, 1.0 %, 8
)
Surround Back . . . . . . . . . . . . 110 W per channel
(1 kHz, 1.0 %, 8
)
Audio section
Input (Sensitivity/Impedance)
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT . . . . . . . . . . . . . . . 200 mV/47 k
Frequency response
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD,
TV/SAT . . . . . . . . . . . . . . 5 Hz to 100 000 Hz dB
Output (Level/Impedance)
DVR/VCR REC, CD-R/TAPE/
MD REC . . . . . . . . . . . . . . . . . . . . . .200 mV/2.2 k
Tone control
Bass . . . . . . . . . . . . . . . . . . . . . . . .± 6 dB (100 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . .± 6 dB (10 kHz)
Loudness . . . . . . +10 dB/+5 dB (100 Hz/10 kHz)
(at volume level –50 dB)
Signal-to-Noise Ratio (IHF, short circuited,
A network)
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT . . . . . . . . . . . . . . . . . . . . . . 96 dB
Signal-to Noise Ratio [EIA, at 1 W (1 kHz)]
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT . . . . . . . . . . . . . . . . . . . . . . 79 dB
Video Section
Input (Sensitivity/Impedance)
DVR/VCR, DVD/LD, TV/SAT. . . . . . . . .1 Vp-p/75
Output (Level/Impedance)
DVR/VCR, MONITOR OUT. . . . . . . . . .1 Vp-p/75
Frequency response
DVR/VCR, DVD/LD,
TV/SAT
MONITOR. . . . . . .5 Hz to 7 MHz dB
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . .55 dB
Crosstalk. . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 dB
Component video section
Input (Sensitivity)
DVD/LD, TV/SAT, DVR/VCR. . . . . . . . .1 Vp-p/75
Output (Level/Impedance)
MONITOR OUT. . . . . . . . . . . . . . . . . . .1 Vp-p/75
Frequency response
DVD/LD, TV/SAT,
DVR/VCR
MONITOR. . . .5 Hz to 40 MHz dB
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . .60 dB
FM Tuner Section
Frequency Range. . . . . . . . 87.5 MHz to 108 MHz
Usable Sensitivity. . . . . . . . . . Mono:13.2 dBf, IHF
(1.3 µV/ 75
)
50 dB Quieting Sensitivity. . . . . . . Mono: 20.2 dB
Stereo: 38.6 dBf
Signal-to-Noise Ratio. . . Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Distortion . . . . . . . . . . . . . . . Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . .60 dB
(400 kHz)
Stereo Separation . . . . . . . . . . . . . . 40 dB (1 kHz)
Frequency Response. . . . . . . . . . 30 Hz to 15 kHz
(±1 dB)
Antenna Input (DIN) . . . . . . . . . 75
unbalanced
Note
1 Continuous average power output of 110 watts* per channel, min., at 8ohms, from 20 Hz to 20 000 Hz with no more than 0.7
%** total harmonic distortion (front).
* Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers.
** Measured by Audio Spectrum Analyzer.
VSX_816.book.fm 64 ページ 2005年12月8日 木曜日 午後6時54分
Additional information
13
65
En
English
Français
Deutsch
Nederlands
Italiano
Español
AM Tuner Section
Frequency Range. . . . . . . . . .530 kHz to 1700 kHz
Sensitivity (IHF, Loop antenna). . . . . . . .350 µV/m
Signal-to-Noise Ratio. . . . . . . . . . . . . . . . . . .50 dB
Antenna . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Miscellaneous
Power requirements . . . . . . . . . . .AC 120V / 60Hz
Power consumption . . . . . . . . . . .370 W / 480 VA
In standby. . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W
Dimensions
. . . . . . . . 16
9
/
16
(W) in. x 6
1
/
4
(H) in. x 13
7
/
8
(D) in.
420 (W) mm x 158 (H) mm x 352.5 (D) mm
Weight (without package). . . . . . . 20.3 lb (9.2 kg)
Furnished Parts
Microphone (for Auto MCACC setup) . . . . . . . . .1
Dry cell batteries (AA size IEC R6)
. . . . . . . . . .2
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . .1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . .1
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . .1
These operating instructions
Note
Specifications and the design are subject
to possible modifications without notice,
due to improvements.
Power cord caution
Handle the power cord by the plug. Do not pull
out the plug by tugging the cord and never
touch the power cord when your hands are wet
as this could cause a short circuit or an electric
shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it
with other cords. The power cords should be
routed such that they are not likely to be
stepped on. A damaged power cord can cause
a fire or give you an electrical shock. Check the
power cord once in a while. When you find it
damaged, ask your nearest Pioneer authorized
service center or your dealer for a replacement.
Cleaning the unit
Use a polishing cloth or dry cloth to wipe
off dust and dirt.
When the surface is dirty, wipe with a soft
cloth dipped in some neutral cleanser
diluted five or six times with water, and
wrung out well, and then wipe again with a
dry cloth. Do not use furniture wax or
cleansers.
Never use thinners, benzine, insecticide
sprays or other chemicals on or near this
unit, since these will corrode the surface.
VSX_816.book.fm 65 ページ 2005年12月8日 木曜日 午後6時54分
Additional information13
66
En
S001_En
Selecting fine audio equipment such as the unit
you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how
you can maximize the fun and excitement your
equipment offers. This manufacturer and the
Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly,
without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing
“comfort level” adapts to higher volumes of sound.
So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your
hearing adapts.
To establish a safe level:
Start your volume control at a low setting.
Slowly increase the sound until you can hear it
comfortably and clearly, and without distortion.
Once you have established a comfortable sound
level:
Set the dial and leave it there.
Taking a minute to do this now will help to prevent
hearing damage or loss in the future. After all, we
want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will
provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often
undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of
sound levels is included for your protection.
Decibel
Level Example
30 Quiet library, soft whispers
40
Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80
Average city traffic, garbage disposals, alarm clock
at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90
Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers,
thunderclap
140 Gunshot blast, jet plane
180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.
VSX_816.book.fm 66 ページ 2005年12月8日 木曜日 午後6時54分
LIMITED WARRANTY
WARRANTY VALID ONLY IN COUNTRY OF PRODUCT PURCHASE
WARRANTY
Pioneer Electronics (USA) Inc. (PUSA), and Pioneer Electronics Of Canada, Inc. (POC), warrant that products distributed by PUSA in the U.S.A., and by POC in Canada that fail to function
properly under normal use due to a manufacturing defect when installed and operated according to the owner’s manual enclosed with the unit will be repaired or replaced with a unit of comparable
value, at the option of PUSA or POC, without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of PUSA or POC.
THIS LIMITED WARRANTY APPLIES TO THE ORIGINAL OR ANY SUBSEQUENT OWNER OF THIS PIONEER PRODUCT DURING THE WARRANTY PERIOD PROVIDED THE
PRODUCT WAS PURCHASED FROM AN AUTHORIZED PIONEER DISTRIBUTOR/DEALER IN THE U.S.A. OR CANADA. YOU WILL BE REQUIRED TO PROVIDE A SALES
RECEIPT OR OTHER VALID PROOF OF PURCHASE SHOWING THE DATE OF ORIGINAL PURCHASE OR, IF RENTED, YOUR RENTAL CONTRACT SHOWING THE PLACE
AND DATE OF FIRST REN TAL. IN THE EVENT SERVICE IS REQUIRED, THE PRODUCT MUST BE DELIVERED WITHIN THE WARRANTY PERIOD, TRANSPORTATION PREPAID,
ONLY FROM WITHIN THE COUNTRY OF PURCHASE AS EXPLAINED IN THIS DOCUMENT. YOU WILL BE RESPONSIBLE FOR REMOVAL AND INSTALLATION OF THE
PRODUCT. PUSA OR POC, AS APPROPRIATE, WILL PAY TO RETURN THE REPAIRED OR REPLACEMENT PRODUCT TO YOU WITHIN THE COUNTRY OF PURCHASE.
PRODUCT WARRANTY PERIOD
Home Audio and Video .......................................................................................................................................................
Microphones, Headphones, Phono Cartridges and Styluses ................................................................................................
Shorter limited warranty periods apply to some models. Please refer to the limited warranty document enclosed with the product for a definitive statement of the warranty period.
The warranty period for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IF THIS PRODUCT WAS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR , THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THIS PRODUCT IS SOLD STRICTLY “AS IS” AND “WITH ALL FAULTS".
PIONEER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL AND/OR INCIDENTAL DAMAGES.
PIONEER DOES NOT WARRANT ANY PRODUCT LISTED ABOVE WHEN IT IS USED IN A TRADE OR BUSINESS OR IN ANY INDUSTRIAL OR COMMERCIAL APPLICATION.
THIS WARRANTY DOES NOT APPLY IF THE PRODUCT HAS BEEN SUBJECTED TO POWER IN EXCESS OF ITS PUBLISHED POWER RATING.
THIS WARRANTY DOES NOT COVER TELEVISION OR DISPLAY SCREENS DAMAGED BY STATIC, NON-MOVING, IMAGES APPLIED FOR LENGTHY PERIODS (BURN-IN).
THIS WARRANTY DOES NOT COVER THE CABINET OR ANY APPEARANCE ITEM, USER ATTACHED ANTENNA, ANY DAMAGE TO RECORDS OR RECORDING TAPES OR DISCS,
ANY
DAMAGE TO THE PRODUCT RESULTING FROM ALTERATIONS, MODIFICATIONS NOT AUTHORIZED IN WRITING BY PIONEER, ACCIDENT, MISUSE OR ABUSE, DAMAGE DUE TO
LIGHTNING OR TO POWER SURGES, SUBSEQUENT DAMAGE FROM LEAKING, DAMAGE FROM INOPERATIVE BATTERIES, OR THE USE OF BATTERIES NOT CONFORMING TO THOSE
SPECIFIED IN THE OWNER’S MANUAL.
THIS WARRANTY DOES NOT COVER THE COST OF PARTS OR LABOR WHICH WOULD BE OTHERWISE PROVIDED WITHOUT CHARGE UNDER THIS WARRANTY OBTAINED FROM
ANY SOURCE OTHER THAN A PIONEER AUTHORIZED SERVICE COMPANY OR OTHER DESIGNATED LOCATION. THIS WARRANTY DOES NOT COVER DEFECTS OR DAMAGE CAUSED
BY THE USE OF UNAUTHORIZED PARTS OR LABOR OR FROM IMPROPER MAINTENANCE.
ALTERED, DEFACED, OR REMOVED SERIAL NUMBERS VOID THIS ENTIRE WARRANTY
NO OTHER WARRANTIES
IN THE U.S.A. - PIONEER LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTER THE
WARRANTY PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND SOME STATES DO NOT ALLOW THE EXCLUSIONS
OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
IN CANADA - EXCEPT AS EXPRESSLY PROVIDED HEREIN, THERE ARE NO REPRESENTATIONS, WARRANTIES, OBLIGATIONS OR CONDITIONS, IMPLIED, STATUTORY
OR OTHERWISE, APPLICABLE TO THIS PRODUCT.
TO OBTAIN SERVICE
PUSA and POC have appointed a number of Authorized Service Companies throughout the U.S.A. and Canada should your product require service. To receive warranty service
youneed to present your sales receipt or, if rented, your rental contract showing place and date of original owner’s transaction. If shipping the unit you will need to package
it carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to
prevent damage in transit. The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business hours.
On all complaints and concerns in the U.S.A. call Customer Support at 1-800-421-1404, or, in Canada, call Customer Satisfaction at (905) 479-4411.
DISPUTE RESOLUTION
IN THE U.S.A. - Following our response to any initial request to Customer Support, should a dispute arise between you and Pioneer, Pioneer makes available its Complaint
Resolution Program to resolve the dispute. The Complaint Resolution Program is available to you without charge. You are required to use the Complaint Resolution Program
before you exercise any rights under, or seek any remedies, created by Title I of the Magnuson-Moss Warranty-Federal Trade Commission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-421-1404 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer product was purchased. After the complaint
has been explained to the representative, a resolution number will be issued. Within 40 days of receiving your complaint, Pioneer will investigate the dispute and will either:
(1) respond to your complaint in writing informing you what action Pioneer will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing
informing you why it will not take any action.
IN CANADA- Call the Customer Satisfaction Manager at 1-877-283-5901 to discuss your complaint and to obtain a prompt resolution.
PIONEER ELECTRONICS (USA) INC. PIONEER ELECTRONICS OF CANADA, INC.
IN THE U.S.A.
For hook-up and operation of your unit or to locate an
Authorized Service Company, please call or write:
CUSTOMER SUPPORT DIVISION
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1760
LONG BEACH, CALIFORNIA 90801
1-800-421-1404
http://www.pioneerelectronics.com
IN CANADA
For additional information on this warranty,
please call or write:
CUSTOMER SATISFACTION GROUP
PIONEER ELECTRONICS OF CANADA, INC.
300 ALLSTATE PARKWAY
MARKHAM, ON L3R 0P2
(905) 479-4411
1-877-283-5901
http://www.pioneerelectronics.com
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No. ____________________________________________ Serial No. _________________________________________ Purchase Date _______________________
Purchased From _______________________________________________________________________________________________________________________________
KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE
Parts
Labor
1 Year 1 Year
90 Days 90 Days
VSX_816.book.fm 67 ページ 2005年12月8日 木曜日 午後6時54分
Published by Pioneer Corporation
Copyright©2005 Pioneer Corporation
All rights reserved
<05L00001> Printed in <XRB3056-A>
Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer
Authorized Independent Service Company, or if you wish to purchase replacement parts,
operating instructions, service manuals, or accessories, please call the number shown
below.
8 0 0 – 4 2 1 – 1 4 0 4
Please do not ship your product to Pioneer without first calling the Customer Support
Division at the above listed number for assistance.
Pioneer Electronics (USA) Inc.
Customer Support Division
P. O. BOX 1760, Long Beach,
CA 90801-1760, U.S.A.
Should this product require service in Canada, please contact a Pioneer Canadian
Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada.
Alternatively, please contact the Customer Satisfaction Department at the following address:
Pioneer Electronics of Canada, Inc.
Customer Satisfaction Department
300 Allstate Parkway, Markham, Ontario L3R OP2
1(877)283-5901
Si ce produit doit être réparé au Canada, veuillez vous adresser à un distributeur autorisé
Pioneer du Canada pour obtenir le nom du Centre de Service Autorisé Pioneer le plus près
de chez-vous. Vous pouvez aussi contacter le Service à la clientèle de Pioneer:
Pioneer Électroniques du Canada, Inc.
Service à la clientèle
300, Allstate Parkway, Markham, Ontario L3R OP2
1(877)283-5901
Pour obtenir des renseignements sur la garantie, veuillez vous reporter au feuillet sur la
garantie restreinte qui accompagne le produit.
S018_A_EF
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002_A_En
VSX_816.book.fm 68 ページ 2005年12月8日 木曜日 午後6時54分
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-816-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-816-K in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info