574181
41
Zoom out
Zoom in
Previous page
1/68
Next page
The System Setup menu
07
41
En
English
Français
Deutsch
Nederlands
Italiano
Español
SB
– Select the number of surround back
speakers you have (one, two or none).
Select
LARGE
if your surround back
speakers reproduce bass frequencies
effectively. Select
SMALL
to send bass
frequencies to the other speakers or
subwoofer. If you didn’t connect surround
back speakers choose
NO
.
1
SUB W.
– LFE signals and bass
frequencies of channels set to
SMALL
are
output from the subwoofer when
YES
is
selected (see notes below). Choose the
PLUS
setting if you want the subwoofer to
output bass sound continuously or you
want deeper bass (the bass frequencies
that would normally come out the front and
center speakers are also routed to the
subwoofer). If you did not connect a
subwoofer choose
NO
(the bass
frequencies are output from other
speakers).
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
If you have a subwoofer and like lots of
bass, it may seem logical to select
LARGE
for your front speakers and
PLUS
for the
subwoofer. This may not, however, yield the
best bass results. Depending on the
speaker placement of your room you may
actually experience a decrease in the
amount of bass due to low frequency
cancellations. In this case, try changing
the position or direction of speakers. If you
can’t get good results, listen to the bass
response with it set to
PLUS
and
YES
or the
front speakers set to
LARGE
and
SMALL
alternatively and let your ears judge which
sounds best. If you’re having problems, the
easiest option is to route all the bass
sounds to the subwoofer by selecting
SMALL
for the front speakers.
Crossover Network
Default setting:
100Hz
This setting decides the cutoff between bass
sounds playing back from the speakers
selected as
LARGE
, or the subwoofer, and bass
sounds playing back from those selected as
SMALL
. It also decides where the cutoff will be
for bass sounds in the LFE channel.
2
1 Select ‘Crossover Network’ from the
Manual SP Setup menu.
2 Choose the frequency cutoff point.
Frequencies below the cutoff point will be sent
to the subwoofer (or
LARGE
speakers).
3 When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
Channel Level
Using the channel level settings, you can
adjust the overall balance of your speaker
system, an important factor when setting up a
home theater system.
Note
1• If the surround speakers are set to
NO
, the surround back speakers will automatically be set to
NO
.
• If you selected
Second Zone
or
Front Bi-Amp
(in
Surround back speaker setting
on page 34) you can’t adjust the surround
back settings.
• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.
2 For more on selecting the speaker sizes, see
Speaker Setting
above.
4.Manual SP Setup
:Return
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
4b.Crossover Network
:Finish
Frequency 80Hz
VSX_816.book.fm 41 ページ 2005年12月8日 木曜日 午後6時54分
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-816-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-816-K in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info