574180
71
Zoom out
Zoom in
Previous page
1/76
Next page
Additional information
13
71
En
English
Français
Deutsch
Nederlands
Italiano
Español
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral
position.
• Make sure the player's settings are correct and/or the DTS signal out
is on. Refer to the instruction manual supplied with the DVD player.
• Set the input signal type to
DIGITAL
(see
Choosing the input signal
on page 38)
When a search is performed
by a DTS compatible CD
player during playback, noise
is output.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Everything seems to be set up
correctly, but the playback
sound is odd.
Check that the positive/negative speaker terminals on the receiver are
matched with the corresponding terminals on the speakers (see
Connecting the speakers
on page 23).
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• See
Automatically setting up for surround sound (MCACC)
on page 12
to set up your system again using MCACC (this will automatically
compensate for a delay in the subwoofer output).
After using the Auto MCACC
Setup, the speaker size
setting (
LARGE
or
SMALL
) is
incorrect.
• Low-frequency noise could have been caused by an air conditioner or
motor. Switch off all appliances in the room and rerun the Auto
MCACC Setup.
Can’t operate the remote
control.
• Replace the batteries (refer to page 7).
• Operate within 23 ft. (7 m), 30° of the remote sensor on the front
panel (refer to page 33).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
• Unplug anything connected to the
CONTROL IN
jack and use remote
normally (see
Operating other Pioneer components
on page 26).
The SR cable is connected,
but the connected
components can’t be
operated with the remote.
• Reinsert the SR cable, making sure it’s connected to the right jack
(see
Operating other Pioneer components
on page 26).
• Make sure an analog connection has been made between the units.
• This feature only works with Pioneer products.
The display is dark or off. • Press
FL DIMMER
on the remote control repeatedly to return to the
default.
Problem
Remedy
VSX_815-915.book.fm 71 ページ 2004年12月8日 水曜日 午後4時3分
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-815-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-815-K in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info