574089
35
Zoom out
Zoom in
Previous page
1/78
Next page
Additional information 09
35
En
English
Français
Deutsch
Nederlands
Italiano
Español
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1 Switch the receiver into standby.
2 While holding down the TONE button,
press and hold the
STANDBY/ON button
for about three seconds.
3 When you see RESET? appear in the
display, press the
ENTER
button.
OK? shows in the display.
4Press
SETUP
to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
No sound from subwoofer. • Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have
an LFE channel.
• Switch the subwoofer setting in Speaker setting on page 28 to YES
or PLUS.
• Switch the LFE Attenuator Setup on page 31 to
LFEATT 0 or
LFEATT 10.
The PHASE CONTROL
feature doesn’t seem to have
an audible effect.
• If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest frequency
setting. If there is a PHASE setting on your subwoofer, set it to 0º (or
depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers
(see Speaker Distance on page 30).
Noise during playback of a
cassette deck.
• Move the cassette deck further from your receiver, until the noise
disappears.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral
position.
During a playback search,
noise is output from a DTS
compatible CD player.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Can’t operate the remote
control.
• Replace the batteries (refer to page 5).
• Operate within 7 m (23 ft.), 30° of the remote sensor on the front
panel (refer to page 5).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off. Press DIMMER on the remote repeatedly to return to the default.
Problem Remedy
VSX_517.fm Page 35 Friday, December 1, 2006 2:41 PM
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-517-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-517-K in the language / languages: English, French as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-517-K

Pioneer VSX-517-K User Manual - English - 63 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info