574063
85
Zoom out
Zoom in
Previous page
1/136
Next page
Controlling the rest of your system 09
85
En
Multi operation and System off
The Multi operation feature allows you to
program a series of up to 5 commands for the
components in your system.
Be sure to call up the preset codes of
devices or perform programming signals
for other remote controls before multi
operation memory programming
(page 82)
.
The Multi operation feature makes it easy to
perform the following operations by pressing
just two buttons.
Press MULTI OPERATION and then the DVD
input function button to:
1. Switch this receiver on.
2. Switch this receiver’s input to DVD.
3. Transmit a sequence of up to five
programmed commands.
Similar to Multi operations, System off allows
you to use two buttons to stop and switch off a
series of components in your system at the
same time.
1
Only one System off operation
sequence may be programmed.
Press
MULTI OPERATION
and then
SOURCE
to:
1. Transmit a sequence of up to five
programmed commands.
2. Switch off all Pioneer devices including the
receiver (except DVD recorders and VCRs).
For greater convenience, program this receiver
to perform power on/off and playback
operations on non-Pioneer devices as well.
2
(The signals for Pioneer devices described
above are not contingent on programming for
non-Pioneer devices.)
The buttons that can be programmed using
Multi operation or System off are the same
buttons as those that can be programmed for
other remote controls (see Programming
signals from other remote controls on page 82).
Programming a Multi operation or a
shutdown sequence
1 Press and hold
R.SETUP
, then press “3
for three seconds.
The LED flashes continuously.
To cancel the preset setup mode press
R.SETUP.
2 Press the input function button (or
SOURCE
button).
For Multi operations, press the input function
you wish to program (for example, if you want
to start the sequence by switching on your DVD
player, press DVD).
3
For System off, press the SOURCE button.
The LED blinks twice and flashes continuously.
3 If necessary, press the input function
button for the component whose command
you want to input.
This is only necessary if the command is for a
new component (input function).
4 Select the button for the command you
want to input.
The LED blinks once and flashes continuously.
You don’t need to program the receiver to
switch on or off. This is done automatically.
Note
1 • Before Multi operation and System off will work correctly, you must setup the remote to work with your TV and other
components (see Operating multiple receivers on page 81 for more on this).
• Some units may take some time to power up, in which case multiple operations may not be possible.
• Power on and off commands only work with components that have a standby mode.
2 Some remote controllers for other manufacturers' devices use the same signals for switching the power on and off.
In some cases, even if this receiver is programmed to perform these commands, power to the non-Pioneer devices
may not be switched on and off correctly. Program the receiver to perform these commands if the non-Pioneer device
uses separate signals for power on/off.
3 With Multi operation, the HDMI and TV CTRL settings cannot be made, but the iPod USB settings can. For other
settable input functions, see Setting the remote to control other components on page 81.
VSX-31_30_UC.book 85 ページ 2010年8月25日 水曜日 午前9時28分
85


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-31 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-31 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info