574063
80
Zoom out
Zoom in
Previous page
1/136
Next page
Using other functions08
80
En
Resetting the system
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front panel
controls to do this. Set
MULTI-ZONE
to
OFF
.
Disconnect the iPod and USB memory
device from the receiver beforehand.
1 Switch the receiver into standby.
2 While holding down
ENTER
on the front
panel, press
STANDBY/ON
.
The display shows RESET NO .
3 Select ‘
RESET
’ using
PRESET /
, then
press
ENTER
on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory default settings.
Note that all settings will be saved, even if
the receiver is unplugged.
Default system settings
Setting Default
Digital Video Conversion ON
SPEAKERS A
Speaker System Normal(SB/FH)
Speaker Setting Front: SMALL
Center: SMALL
FH/FW: SMALL
Surr: SMALL
SB: SMALLx2
SW: YES
Surround Position IN REAR
Crossover 80 Hz
X-Curve OFF
DIMMER brightest
Inputs
See Input function default and possible settings on
page 45.
HDMI
HDMI Audio Amp
Control ON
Control Mode ALL
DIsplay Power Off YES
DSP
Power On Level LAST
Volume Limit OFF
Mute Level FULL
Phase Control ON
Sound Retriever ON
(iPod/USB, INTERNET
RADIO, ADAPTER PORT
function)/
OFF (Other functions)
Sound Delay 0.0 frame
Dual Mono CH1
DRC AUTO
SACD Gain 0 dB
LFE Attenuate 0 dB
Auto delay OFF
Digital Safety OFF
Effect Level 90 (EXT.STEREO)/
50 (Other modes)
2 PL II Music Options Center Width:3
Dimension:0
Panorama:OFF
Neo:6 Options Center Image:
3 (Neo:6 MUSIC)/
10 (Neo:6 CINEMA)
Listening Mode
(All Inputs)
AUTO SURROUND
(2 ch/multi ch)/
STEREO (Head phones)
See also Setting the Audio options on page 72 for
other default DSP settings.
MCACC
MCACC Position Memory
M1: MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance
(M1 to M6)
10’00”
Standing Wave
(M1 to M6)
ATT of all channels/
filters: 0.0 dB
SWch Trim: 0.0 dB
EQ Data (M1 to M6)
All channels/bands: 0.0 dB
EQ Trim: 0.0 dB
Setting Default
VSX-31_30_UC.book 80 ページ 2010年8月25日 水曜日 午前9時28分
80


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-31 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-31 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info