574064
115
Zoom out
Zoom in
Previous page
1/136
Next page
Additional information 12
115
En
Other audio problems
Symptom Remedy
Broadcast stations cannot be
selected automatically, or
there is considerable noise in
radio broadcasts.
For FM broadcasts
• Fully extend the FM wire antenna, adjust the position for best reception and
secure to a wall, etc.
• Use an outdoor antenna for better reception (see page 31).
For AM broadcasts
• Adjust the position and direction of the AM antenna.
• Use an outdoor antenna for better reception (see page 31).
• Noise may be caused by interference from other equipment, such as a
fluorescent light, motor, etc. Switch off or move the other equipment, or move
the AM antenna.
Noise is output when
scanning a DTS CD.
• This is not a malfunction of the receiver. The scan function of your player
alters the digital information, making it unreadable, resulting in noise being
output. Lower the volume when scanning.
When playing a DTS format
LD there is audible noise on
the soundtrack.
• Make sure that the input signal type is set to DIGITAL (see Choosing the input
signal on page 65).
Can’t record audio. • You can only make a digital recording from a digital source, and an analog
recording from an analog source.
• For digital sources, make sure that what you’re recording isn’t copy protected.
• Check that the OUT jacks are properly connected to the recorders input jacks
(see Connecting other audio components on page 30).
Subwoofer output is very low. • To route more signal to the subwoofer, set it to PLUS or set the front speakers
to SMALL (see Speaker Setting on page 106).
Everything seems to be set up
correctly, but the playback
sound is odd.
• The speakers may be out of phase. Check that the positive/negative speaker
terminals on the receiver are matched with the corresponding terminals on the
speakers (see Connecting the speakers on page 20).
The PHASE CONTROL
feature doesn’t seem to have
an audible effect.
• If applicable, check that the lowpass filter switch on your subwoofer is off, or
the lowpass cutoff is set to the highest frequency setting. If there is a PHASE
setting on your subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see Speaker
Distance on page 107).
Noise or hum can be heard
even when there is no sound
being input.
• Check that personal computers or other digital components connected to the
same power source are not causing interference.
Can’t select some Input
functions by the INPUT
SELECTOR on the front panel
or the INPUT SELECT button
on the remote control.
• Check the Input Skip settings in the Input Setup menu.
• Check the HDMI Input assignment in the Input Setup menu then try OFF.
There seems to be a time lag
between the speakers and
the output of the subwoofer.
• See Automatically conducting optimum sound tuning (Auto MCACC on
page 41 to set up your system again using MCACC (this will automatically
compensate for a delay in the subwoofer output).
VSX-31_30_UC.book 115 ページ 2010年8月25日 水曜日 午前9時28分
115


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-30 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info