Manual Pioneer VSX-1130 K (page 93 of 137) (English)

586461

Zoom out

Zoom in

1/137

Controlling the rest of your system (VSX-1130 only)

About the Remote Setup menu

The Remote Setup mode is set by pressing the number button while pressing RCU SETUP. The different items

on the Remote Setup menu are described below. For their setting procedures, refer to the explanations for the

respective items.

Setting What it does

Change RC

mode

If you have multiple Pioneer receivers, amplifiers, etc., this setting can be used to prevent other units from

operating simultaneously when the remote control unit is operated. See Operating multiple receivers on

page 93 .

Preset recall

Preset codes can be set for the various input functions. The remote control codes of a number of other

devices (including products of other brands) are preset in the remote control to allow these devices to be

operated. See Selecting preset codes directly on page 93 .

Code learning

If the desired operations cannot be performed even though you have set the preset codes, the remote control

signals of other devices can be learned directly. See Programming signals from other remote controls on

page 94 .

Erase learning

This function is used to erase remote control codes that have been learned. Codes learned for the different

input functions can be erased individually. See Erasing one of the remote control button settings on page

94 .

Reset function

This is a function for resetting preset codes that have been set. Key resetting can be done for individual input

functions. See Erasing all learnt settings that are in one input function on page 94 .

Operation

mode switching

time

You can set to automatically switch to AV amplifier operation mode when a certain period of time elapses

after remote operation of each input function is finished. See Setting the switching time for the receiver

operation mode on page 95 .

All reset

This is a function for resetting all remote control unit settings you have made to the defaults set upon ship-

ment from the factory. See Resetting the remote control settings on page 95 .

Notes

! You can cancel or exit any of the steps by pressing RCU SETUP.

! After one minute of inactivity, the remote automatically exits the operation.

Operating multiple receivers

Up to four receivers can be operated discretely using this receiver’s remote control when using multiple receiv-

ers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the

preset code to set the remote control setting.

! Set the remote modes on the receivers before using this function (see Remote Control Mode Setup on page

110 ).

1 Press and hold RCU SETUP, then press ‘4’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To cancel the preset setup mode press RCU SETUP.

2 Press the number button for the receiver (“Receiver 1” to “Receiver 4”) you wish to

operate.

For example, to operate “Receiver 2”, press ‘2’.

If the LED lights for one second, the setting has been successfully completed.

When the preset code is input, the LED flashes three times to indicate that the setting has failed.

Setting the remote to control other components

Most components can be assigned to one of the input function buttons (such as DVD or CD) using the compo-

nent’s manufacturer preset code stored in the remote.

However, there are cases where only certain functions may be controllable after assigning the proper preset

code, or the codes for the manufacturer in the remote control will not work for the model that you are using.

If you can’t find a preset code that matches the component you want to control, you can still teach the remote

individual commands from another remote control (see Programming signals from other remote controls on

page 94 ).

! With the TV buttons, the TV can be operated regardless of the input set for the remote control’s operation

mode. When using one TV set, we recommend assigning the same TV’s preset codes to the TV INPUT button

and the TV button. When using two TV sets, for better convenience assign the TV connected to the MONITOR

OUT terminals to the TV INPUT button, the other TV to the TV button.

! Devices may be assigned to the following input function buttons.

SOURCE CONTROL

STANDBY/ON

DVDBD SAT

HDMI

TV CD

INPUT

ALL

Selecting preset codes directly

1 Press and hold RCU SETUP, then press ‘1’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

! To cancel the preset setup mode press RCU SETUP.

2 Press the input function button for the component you want to control.

To assign the preset codes of the TV to be operated with the TV function, press the TV INPUT button.

The LED of the remote control lights.

3 Use the number buttons to enter the 4-digit preset code.

See Preset code list on page 134 .

If the LED lights for one second and continues to flash, the setting has been successfully completed.

When the preset code is fully input, the LED flashes three times to indicate that the setting has failed. If this hap-

pens, enter the 4-digit preset code again.

4 Repeat steps 2 through 3 for the other components you want to control.

To try out the remote control, switch the component on or off (into standby) by pressing u SOURCE. If it doesn’t

seem to work, select the next code from the list (if there is one).

5 Press RCU SETUP to exit the preset setup mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1130 K in the language / languages: English as an attachment in your email.

The manual is 20,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1130 K

Pioneer VSX-1130 K User Manual - German - 146 pages

Pioneer VSX-1130 K User Manual - Dutch - 146 pages

Pioneer VSX-1130 K User Manual - French - 145 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer VSX-1130 K Manual

Product: