536829
96
Zoom out
Zoom in
Previous page
1/115
Next page
96
 
 
 
 
13
FAQ
HDMI
Symptom Remedy
The HDMI indicator blinks continu-
ously.
Check all the points below.
No picture or sound. This receiver is HDCP-compatible. Check that the components you are connecting are
also HDCP-compatible. If they are not, please connect them using the component or
composite video jacks.
Depending on the connected source component, it’s possible that it will not work with
this receiver (even if it is HDCP-compatible). In this case, connect using the component
or composite video jacks between source and receiver.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
If video images do not appear on your TV, try adjusting the resolution, Deep Color or other
setting for your component.
While analog video signals are being output over HDMI, use a separate connection for
audio output.
To output signals in Deep Color, use an HDMI cable (High Speed HDMI
®
/
TM
Cable) to
connect this receiver to a component or TV with the Deep Color feature.
Influence from a TV whose power is set to standby may cause the picture or sound not to
be produced or to be broken. In this case, press HDMI OUT and switch so that the HDMI
output to which that TV is connected is not selected.
No picture.
Try changing the Resolution setting (in Setting the Video options on page 65).
To use the HDMI OUT 2 terminal in the main zone, set the MAIN/HDZONE
Output Setting to MAIN (page 88).
No sound, or sound suddenly
ceases.
Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 63).
If the component is a DVI device, use a separate connection for the audio.
If analog video is being output over HDMI, please use a separate connection for the
audio.
Check the audio output settings of the source component.
HDMI format digital audio transmissions require a longer time to be recognized. Due
to this, interruption in the audio may occur when switching between audio formats or
beginning playback.
Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,
or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-
rupted audio.
Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
HDCP ERROR shows in the display. Check whether or not the connected component is compatible with HDCP. If it is not
compatible with HDCP, reconnect the source device using a different type of connection
(component or composite). Some components that are compatible with HDCP still cause
this message to be displayed, but so long as there is no problem with displaying video,
this is not a malfunction.
Symptom Remedy
Synchronized operation not possible
using Control with HDMI function.
Check the HDMI connections.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 59).
Turn the TV’s power on before turning on this receiver’s power.
Set the TV side Control with HDMI setting to on (see TV’s operating instructions).
Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to OUT 1. Then
turn on first the TV’s power, then this receiver’s power.
When HDZONE is set to ON, the
video resolution and number of
audio channels for the main zone
side changes.
This is due to the HDMI connection specifications; it is not a malfunction. When play-
ing the same input in the main zone and HDZONE, video and audio signals that can be
output in common for all the devices connected to the HDMI OUT 1 and HDMI OUT 2
(HDZONE) terminals are set.
HDZONE cannot be turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 88).
When the input source for the main
or HD zone is switched or when the
power of the respective zones is
turned on and off, the audio or video
of the HDMI output terminal that is
not being operated is sometimes
interrupted.
This is because the HDMI devices need to recognize each other again. This is not a
malfunction. If the picture is disturbed or not displayed, turn off the power of the devices
in all the zones, then try again. Also try temporarily turning the Network Standby and
Standby Through settings OFF.
MHL
Symptom Remedy
When playing an MHL-compat-
ible device connected to the
HDMI 5/MHL terminal, the Standby
Through function does not work and
the power turns off.
The MHL device will not operate unless power is being supplied from this receiver. When
this receiver is in the Standby Through mode, power cannot be supplied due to reduced
power consumption. Because of this, the MHL device will not operate. This is not a mal-
function.
MHL-compatible device cannot be
operated with the remote control.
Press MHL to set the remote control to the MHL control mode.
AVNavigator
Symptom Causes Remedy
AVNavigator cannot be
installed.
An error message may appear
if there are not enough system
resources available.
Restart the computer and start installing with no other
applications running.
Installation of AVNavigator may fail
because of incompatibilities with
other applications.
Try the following (in given order):
1. If other applications are running on the computer, quit
those applications before installing.
2. If the problem persists, restart the computer and install
with no other applications running.
96


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1123 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1123 in the language / languages: English as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1123

Pioneer VSX-1123 Quick start guide - English, German - 44 pages

Pioneer VSX-1123 User Manual - German - 120 pages

Pioneer VSX-1123 Quick start guide - Dutch - 44 pages

Pioneer VSX-1123 User Manual - Dutch - 118 pages

Pioneer VSX-1123 User Manual - Danish - 226 pages

Pioneer VSX-1123 Quick start guide - French - 44 pages

Pioneer VSX-1123 User Manual - French - 117 pages

Pioneer VSX-1123 Quick start guide - Italian - 44 pages

Pioneer VSX-1123 User Manual - Italian - 117 pages

Pioneer VSX-1123 User Manual - Swedish - 115 pages

Pioneer VSX-1123 User Manual - Turkish - 116 pages

Pioneer VSX-1123 Quick start guide - Spanish - 44 pages

Pioneer VSX-1123 User Manual - Spanish - 115 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info