574087
92
Zoom out
Zoom in
Previous page
1/113
Next page
92
 
 
 
 
13
FAQ
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate
the other components and electrical appliances being used. If the trouble cannot be rectified even after exercis-
ing the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair
work.
! If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on
the remote control or front panel stop working completely, do the following:
! Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.
! If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over 10 seconds. The
power will turn off. In this case, the various settings made on the receiver may be cleared. (However, settings
made when the power was turned off normally are not cleared.)
Power
Symptom Remedy
The power does not turn on. Make sure that the power cord is plugged in to an active power outlet.
Try disconnecting from the power outlet, then plugging back in.
Power cannot be turned off.
(ZONE 2 ON is displayed.)
Press the remote control’s ZONE 2, then press u STANDBY/ON to switch the sub zone
off.
Power cannot be turned off.
(HDZONE ON is displayed.)
Press the remote control’s HDZONE, then press u STANDBY/ON to switch the sub zone
off.
The receiver suddenly switches off
or the iPod iPhone iPad indicator
blinks.
Check that there are no loose strands of speaker wire touching the rear panel or another
set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.
The receiver may have a serious problem. Disconnect from the power and call a Pioneer
authorized independent service company.
During loud playback the power sud-
denly switches off.
Turn down the volume.
Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 78.
Switch on the digital safety feature. While holding down ENTER on the front panel,
press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to
select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY
cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn
down the volume. With 1 or 2 on, some features may be unavailable.
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 84).
The unit does not respond when the
buttons are pressed.
Try switching the receiver off, then back on again.
Try disconnecting the power cord, then connect again.
AMP ERR blinks in the display, then
the power automatically switches off.
The ADVANCED MCACC blinks and
the power does not turn on.
The receiver may have a serious problem. Do not try switching the receiver on. Unplug the
receiver from the wall and call a Pioneer authorized independent service company.
The receiver suddenly switches off or
the FL OFF indicator blinks.
There is a problem with the receiver’s power unit or fan. Try turning on the power. If the
same thing happens, the receiver is damaged. Unplug the receiver from the wall and call
a Pioneer authorized independent service company. (Other symptoms may appear when
the power is turned on.)
Symptom Remedy
AMP OVERHEAT blinks in the dis-
play and the FL OFF indicator flash
and the power turns off.
Allow the unit to cool down in a well-ventilated place before switching back on (see
Installing the receiver on page 8).
Check whether the cables used to connect the speakers are short-circuited.
Wait at least 1 minute, then try turning the power on again.
The temperature within the unit has exceeded the allowablevalue.
Lower the volume level.
HDZONE cannot be turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 88).
No sound
Symptom Remedy
No sound is output when an input
function is selected.
No sound is output from the front
speakers.
Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
Make sure the correct input function is selected.
Check that the MCACC setup microphone is disconnected.
Make sure the correct input signal is selected (press SIGNAL SEL).
Note that when Fixed PCM ON is selected, you won’t be able to hear any other signal
format (see Setting the Audio options on page 63).
Check that the source component is connected properly (see Connecting your equipment
on page 17).
Check that the speakers are connected properly (see Connecting the speakers on page
20).
No sound from the surround or
center speakers.
Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t
selected; select one of the surround listening modes (see Enjoying various types of play-
back using the listening modes on page 49).
Check that the surround/center speakers are not set to NO (see Speaker Setting on page
84).
Check the channel level settings (see Channel Level on page 85).
Check the speaker connections (see Connecting the speakers on page 20).
No sound from surround back
speakers.
Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 84).
Check the speaker connections (see Connecting the speakers on page 20). If only one
surround back speaker is connected, make sure it’s connected to the left channel
speaker terminal.
Surround back speakers will not play while the Speaker System is set to Speaker B and
audio is being played through speaker B.
When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: FH ON or
SP: FW ON is selected with the SPEAKERS button, no sound will be output from the sur-
round back speakers. Select SP: SB/FH ON, SP: SB/FW ON or SP: SB ON (see Switching
the speaker terminals on page 67).
No sound from front height or front
wide speakers.
Check that the front height or front wide speakers are set to LARGE or SMALL, and the
surround speakers are not set to NO (see Speaker Setting on page 84).
When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: SB ON is
selected with the SPEAKERS button, no sound will be output from the front height or
front wide speakers. Select SP: SB/FH ON, SP: SB/FW ON, SP: FH ON or SP: FW ON (see
Switching the speaker terminals on page 67).
Check the speaker connections (see Connecting the speakers on page 20).
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1123-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1123-K in the language / languages: English as an attachment in your email.

The manual is 3,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1123-K

Pioneer VSX-1123-K Quick start guide - English, German - 44 pages

Pioneer VSX-1123-K User Manual - German - 120 pages

Pioneer VSX-1123-K Quick start guide - Dutch - 44 pages

Pioneer VSX-1123-K User Manual - Dutch - 118 pages

Pioneer VSX-1123-K User Manual - Danish - 226 pages

Pioneer VSX-1123-K Quick start guide - French - 44 pages

Pioneer VSX-1123-K User Manual - French - 117 pages

Pioneer VSX-1123-K Quick start guide - Italian - 44 pages

Pioneer VSX-1123-K User Manual - Italian - 117 pages

Pioneer VSX-1123-K User Manual - Swedish - 115 pages

Pioneer VSX-1123-K User Manual - Turkish - 116 pages

Pioneer VSX-1123-K Quick start guide - Spanish - 44 pages

Pioneer VSX-1123-K User Manual - Spanish - 115 pages

Pioneer VSX-1123-K User Manual - Norwegian - 115 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info