491802
87
Zoom out
Zoom in
Previous page
1/107
Next page
87
13
FAQ
Symptom Remedy
No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.
If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 80).
The crossover frequency may be set too low; try setting it higher to match the characteris-
tics of your other speakers (see Speaker Setting on page 80).
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 80).
Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the
Audio options on page 58).
Check the speaker level settings (see Channel Level on page 81).
No sound from one speaker.
Check the speaker connection (see Connecting the speakers on page 19).
Check the speaker level settings (see Channel Level on page 81).
Check that the speaker hasn’t been set to NO (see Speaker Setting on page 80).
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see Enjoying various
types of playback using the listening modes on page 45).
Sound is produced from analog
components, but not from digital
ones (DVD, LD, CD, etc.).
Check that the input signal type is set to DIGITAL (see Choosing the input signal on page
46).
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see The Input Setup menu on page 35).
Check the digital output settings on the source component.
If the source component has a digital volume control, make sure this is not turned down.
No sound is output or a noise is out-
put when Dolby Digital/DTS software
is played back.
Check that your BD or DVD player is compatible with Dolby Digital/DTS discs.
Check the digital output settings or the HDMI audio output settings of your BD or DVD
player. Make sure that the DTS signal output is set to On.
If the source component has a digital volume control, make sure this is not turned down.
No sound when using the
Home Menu.
If the HDMI input function is selected, sound is muted until exiting the Home Menu.
Other audio problems
Symptom Remedy
Speaker switching sound (clicking
sound) is heard from receiver during
playback.
Depending on the listening mode, the front height (or front wide) and surround back
speakers may switch automatically in function of changes in the input audio. A speaker
switching sound (clicking sound) will be heard from the receiver at this time. If this sound
bothers you, we recommend to change the speaker terminal option (see Switching the
speaker terminals on page 62).
Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broad-
casts.
Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.
Use an outdoor antenna for better reception (see page 28).
Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.
Symptom Remedy
Noise is output when scanning a
DTS CD.
This is not a malfunction of the receiver. The scan function of your player alters the digital
information, making it unreadable, resulting in noise being output. Lower the volume
when scanning.
When playing a DTS format LD there
is audible noise on the soundtrack.
Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on
page 46).
Subwoofer output is very low.
To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 80).
Everything seems to be set up cor-
rectly, but the playback sound is odd.
The speakers may be out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding terminals on the speakers (see Connect-
ing the speakers on page 19).
The Phase Control feature doesn’t
seem to have an audible effect.
If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-
woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see Speaker Distance
on page 81).
Noise or hum can be heard even
when there is no sound being input.
Check that personal computers or other digital components connected to the same
power source are not causing interference.
Can’t select some Input functions by
the INPUT SELECTOR on the front
panel or the INPUT SELECT button
on the remote control.
Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on
page 35).
Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input
Setup menu on page 35).
There seems to be a time lag
between the speakers and the output
of the subwoofer.
See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 33 to
set up your system again using MCACC (this will automatically compensate for a delay in
the subwoofer output).
The maximum volume available
(shown in the front panel display) is
lower than the +12dB maximum.
Check that the Volume Limit is set to OFF (see Volume Setup on page 83).
The channel level setting may be over 0.0dB.
Certain listening modes or
HOME MENU items cannot be
selected.
When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
not all of the functions can be used. To use all of the functions without restrictions, set
Operation Mode to Expert (see Operation Mode Setup on page 36).
The volume level drops automati-
cally.
The temperature within the unit has exceeded the allowable value. Try moving the unit for
better ventilation (see Installing the receiver on page 8).
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1122K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1122K in the language / languages: English as an attachment in your email.

The manual is 8,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1122K

Pioneer VSX-1122K Quick start guide - English, German - 44 pages

Pioneer VSX-1122K User Manual - German - 113 pages

Pioneer VSX-1122K Quick start guide - Dutch - 44 pages

Pioneer VSX-1122K User Manual - Dutch - 111 pages

Pioneer VSX-1122K Quick start guide - French, Italian, Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info