455217
38
Zoom out
Zoom in
Previous page
1/128
Next page
Basic Setup04
38
En
Select Normal (Surround back), Speaker B,
Front Bi-Amp or ZONE 2 for the Surr Back
System setting according to connections to
the surround back speaker terminals.
4 Follow the instructions on-screen.
Make sure the microphone is connected, and if
you’re using a subwoofer, make sure it is switched
on and set to a comfortable volume level.
5 Wait for the test tones to finish, then
confirm the speaker configuration in the GUI
screen.
A progress report is displayed on-screen while
the receiver outputs test tones to determine the
speakers present in your setup. Try to be as
quiet as possible while it’s doing this.
1
If no operations are performed for 10 seconds
while the speaker configuration check screen
is being displayed, the Auto MCACC Setup will
resume automatically. In this case, you don’t
need to select ‘OK’ and press ENTER in step 6.
•With error messages (such as Too much
ambient noise! or Check microphone.)
select RETRY after checking for ambient
noise (see Problems when using the Auto
MCACC Setup below) and verifying the mic
connection. If there doesn’t seem to be a
problem, you can simply select GO NEXT
and continue.
The configuration shown on-screen should
reflect the actual speakers you have.
If you see an ERR message (or the sp eaker
configuration displayed isn’t correct), there
may be a probl
em wit
h the speaker
connection.
If selecting RETRY doesn’t work, turn off
the power and check the speaker
connections. If there doesn’t seem to be a
problem, you can simply use / to select
the speaker and / to change the
setting and continue.
•If Reverse Phase is disp layed, the
speaker’s wiring (+ and –) may be inverted.
Check the speaker connections.
2
If the connections were wrong, turn off the
power, disconnect the power cable, then
reconnect properly. After this, perform the
Full Auto MCACC procedur e again.
6 Make sure ‘
OK
’ is selected, then press
ENTER
.
A progress report is displayed on-screen while
the receiver outputs more test tones to
determine the optimum receiver settings for
Channel Level, Speaker Distance, Standing
Wave and Acoustic Cal EQ.
Again, try to be as quiet as possible while this
is happening. It may take 3 to 10 minutes.
Note
1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
Now Analyzing... 2/10
Environment Check
1a.Full Auto MCACC
A/V RECEIVER
Exit Cancel
Ambient Noise : OK
Microphone :
Speaker YES/NO :
L : YES
R : YES
C : YES
1a.Full Auto MCACC
SR : YES
SBR : YES
SBL : YES
SL : YES
SW : YES
10
OK RETRY
A/V RECEIVER
Exit Cancel
2If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase
(dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are properly
connected. If this happens, select GO NEXT and continue.
VSX-1019_KU.book 38 ページ 2009年2月17日 火曜日 午前11時56分
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1019AH-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1019AH-K in the language / languages: English as an attachment in your email.

The manual is 9,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1019AH-K

Pioneer VSX-1019AH-K User Manual - German - 127 pages

Pioneer VSX-1019AH-K User Manual - Dutch - 127 pages

Pioneer VSX-1019AH-K User Manual - French - 127 pages

Pioneer VSX-1019AH-K User Manual - Italian - 127 pages

Pioneer VSX-1019AH-K User Manual - Swedish - 251 pages

Pioneer VSX-1019AH-K User Manual - Spanish - 127 pages

Pioneer VSX-1019AH-K User Manual - Norwegian, Finnish - 251 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info