574077
71
Zoom out
Zoom in
Previous page
1/76
Next page
Additional information
12
71
En
Remote control
Note
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
Resetting the main unit
Use this procedure to reset all the receiver’s settings to
the factory default. Use the front panel controls to do this.
1 Switch the receiver into standby.
2 While holding down the TONE button, press and
hold the
STANDBY/ON button for about three
seconds.
3 When you see RESET? appear in the display,
press ENTER.
OK?
shows in the display.
4 Press SYSTEM SETUP to confirm.
OK
appears in the display to indicate that the receiver
has been reset to the factory default settings.
Switching the speaker impedance
We recommend using speakers of 8
with this system,
but it is possible to switch the impedance setting if you
plan to use speakers with a 6
impedance rating.
With the receiver in standby, press
STANDBY/
ON while holding down the SPEAKERS button.
Each time you do this, you switch between the
impedance settings:
SP 6 OHM
– Use this setting if your speakers are
rated at 6
.
SP 8 OHM
– Use this setting if your speakers are
rated at 8
or more.
Symptom Cause Remedy
Cannot be remote controlled. • The remote control batteries have worn out. • Replace the batteries (see
Loading the batteries
on
page 7).
• Too far away or improper angle of operation. Operate within 23 feet and a 30º angle of the remote
sensor on the front panel (see
Operating range of remote
control unit
on page 30).
• There is an obstacle between the receiver
and the remote control.
• Remove the obstacle or move to another place.
• Strong light such as fluorescent light is
shining onto the unit's remote control sensor.
• Avoid exposing the remote sensor on the front panel to
direct light.
• Something is plugged into the
CONTROL IN
jack.
• Unplug the cable from the
CONTROL IN
jack and use
remote normally (see
Operating other Pioneer components
on page 23).
Other components can't be
operated with the system
remote.
• The preset code settings are wrong.
• The batteries wore out and the system
settings were cleared.
• Input the correct preset code.
• Reset the proper system settings.
The SR cable is connected, but
the connected components can’t
be operated with the remote.
• The SR cable hasn't been connected
properly.
• Reinsert the SR cable, making sure it’s connected to the
right jack (see
Operating other Pioneer components
on
page 23).
• The rest of the component connections
have not been made.
• Make sure an analog connection has been made
between the units.
• The component you have hooked up is not a
Pioneer product.
• This feature only works with Pioneer products.
VSX_1015.book.fm 71 ページ 2004年11月29日 月曜日 午後2時38分
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1015TX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1015TX in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info