574062
99
Zoom out
Zoom in
Previous page
1/104
Next page
Additional information
11
99
En
USB interface
Miscellaneous
Note
If the unit does not operate normally due to external
effects such as static electricity, disconnect the
power plug from the outlet and insert again to return
to normal operating conditions.
NO SIGNAL A component is outputting an i.LINK signal that the amplifier cannot reproduce. This amplifier can only
reproduce signals from i.LINK-Audio-equipped components. See About i.LINK on page 79 for more on
this.
PQLS OFF This is displayed when PQLS turns off during playback. The sound may be interrupted momentarily when
this happens.
PQLS ON This is displayed when PQLS turns on during playback. The sound may be interrupted momentarily when
this happens.
UNKNOWN When an i.LINK-equipped component name cannot be recognized, this message is displayed instead of
the proper component name.
Message Explanation
Symptom Cause Remedy
No sound. • The computer settings are incorrect. • Make sure you have set up your computer system to
output through the USB interface (see Using the USB
interface on page 80).
• The software or source material you are
using is not compatible with USB output.
• Update to a more recent version of your existing
software, try a different audio program, or try a different
source.
• The volume control on your computer is set
too low.
• Turn up the volume on your computer.
No sound from one or more
channels.
• The software settings are incorrect, or the
program you are using cannot output
multichannel audio.
• Try changing the software settings. If this doesn’t work,
update to a more recent version of your existing software,
or try a different audio program.
• The wrong input setting is selected for the
USB interface.
• Change the setting accordingly (see Selecting USB and
multichannel analog input channels on page 45).
Symptom Cause Remedy
The amplifier doesn’t seem to
respond when the buttons are
pressed.
• Static electricity caused by dry air. • Switch the power off then on again. If this doesn’t seem
to work, try disconnecting the power plug from the outlet,
and insert again.
One of the Home THX 7.1
channel modes is selected, but
there are certain options that
can't be chosen.
• There is only one surround back speaker
connected or the current settings are for only
one surround back speaker.
• Make sure there are two surround back speakers
connected (see Connecting the speakers on page 24) and
make the necessary settings in Speaker Systems on
page 52.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• The subwoofer channel can be delayed
slightly if run through a low-pass filter.
• See Automatically setting up for surround sound on
page 35 to set up your system again using MCACC (this
will automatically compensate for a delay in the
subwoofer output).
The amplifier doesn’t memorize
the last volume level you used
before switching it off.
• The amplifier was switched off immediately
after changing the volume level.
• Make sure to switch off the amplifier two seconds or
more after changing the volume.
The amplifier doesn’t memorize
the last adjustments you made
before switching it off.
• The amplifier was switched off immediately
after changing the amplifier status.
• Make sure to switch off the amplifier two seconds or
more after changing the amplifier status.
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSA-AX10i-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSA-AX10i-S in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSA-AX10i-S

Pioneer VSA-AX10i-S User Manual - English - 25 pages

Pioneer VSA-AX10i-S User Manual - German - 104 pages

Pioneer VSA-AX10i-S User Manual - Dutch - 104 pages

Pioneer VSA-AX10i-S User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info