574062
69
Zoom out
Zoom in
Previous page
1/104
Next page
Using other functions
08
69
En
Chapter 8
Using other functions
Making an audio or a video recording
You can make an audio or a video recording from an
audio or video source connected to the amplifier (such as
a CD player or TV).
Keep in mind you can't make a digital recording from an
analog source or vice-versa, so make sure the
components you are recording to/from are hooked up in
the same way (see Connecting your equipment on
page 12 for more on connections).
You can record using composite and S-video
connections interchangeably, but you won’t be able to
record sources connected to the component video
inputs. See About the video converter on page 20 for more
on this.
For more information about video connections, see
Connecting a VCR or DVD recorder on page 18 and
Connecting other video sources on page 19.
1 Select the source you want to record.
Use the INPUT buttons (or the INPUT SELECTOR dial on
the front panel).
2 Select the input signal (if necessary).
Press SIGNAL SELECT to select the input signal
corresponding to the source component (see Selecting
the input signal type on page 44 for more on this).
3 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component's instruction manual if you're unsure.
5 Start recording, then start playback of the source
component.
Note
The amplifier's volume, tone (bass, treble, Midnight,
Loudness), and surround effects have no effect on
the recorded signal.
Some digital sources are copy-protected, and can
only be recorded in analog.
Some video sources are copy-protected. These
cannot be recorded.
Monitoring your recording
You can listen to (monitor) the recording as it’s being
made if you’ve connected a cassette deck with a
monitoring function to the TAPE 2 MONITOR jacks on
the rear panel.
Press TAPE 2 MONITOR to switch between the
recorded signal and the original source signal.
With the remote, you may need to press on the
Home menu ( ) first before reaching the amplifier
menu screen shown below (use the / (cursor left/
right) soft keys to go to the previous/next menu screen).
Tip
To record the tape 2 monitor signal to a recorder
connected to the CD-R/TAPE 1 inputs, select any
input (except CD-R/TAPE 1) and switch the tape 2
monitor on.
AMPLIFIER
AMPLIFIER
3/3
SB CH
MODE
INPUT
STATUS
INPUT
AT T
SPEAKER
A/B
VIDEO
SELECT
TAPE2
MONITOR
DISPLAY
DIMMER
AMPLIFIER
TV
CONT
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
SB CH
MODE
DIGITAL IN
S-VIDEO VIDEO
VIDEO INPUT
AUDIOLR
MIDNIGHT
LOUDNESS OPTIONTONE DIGITAL NR INPUT ATT
SELECT
CH LEVEL
ACOUSTIC
CAL.
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSA-AX10i-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSA-AX10i-S in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSA-AX10i-S

Pioneer VSA-AX10i-S User Manual - English - 25 pages

Pioneer VSA-AX10i-S User Manual - German - 104 pages

Pioneer VSA-AX10i-S User Manual - Dutch - 104 pages

Pioneer VSA-AX10i-S User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info