574062
44
Zoom out
Zoom in
Previous page
1/104
Next page
Listening to your system
05
44
En
Listening with Acoustic Calibration
EQ
You can listen to sources using the Acoustic Calibration
Equalization set in Automatically setting up for surround
sound on page 35 or Acoustic Calibration EQ on page 55.
Refer to these pages for more on acoustic calibration
equalization.
While listening to a source, press ACOUSTIC CAL.
to select an Acoustic Calibration EQ setting.
Press repeatedly to select between:
ALL CH ADJ – No special weighting is given to any
one channel.
FRONT CH ALIGN – All speakers are heard in
accordance with the front speaker settings.
CUSTOM 1/2 – Custom settings
OFF – Switches Acoustic Calibration EQ off.
Selecting the input signal type
Most of the audio inputs have both analog and digital
jacks. You can select the type of signal to be used in each
case.
The input signal type for the current input is indicated in
the display. With digital signals, the signal type (Dolby
Digital or DTS) also shows in the display.
The default AUTO setting is usually sufficient, letting the
amplifier decide the most suitable signal type. However,
if you want to record from the DVR/VCR1 IN/OUT jacks,
then you should set the input signal type to analog.
If you have selected the USB interface or the
multichannel analog inputs as your input source, see
Selecting USB and multichannel analog input channels
below.
Press SIGNAL SELECT to select the type of input
signal for the current source.
With the remote, you may need to press on the
Home menu ( ) first before reaching the amplifier
menu screen shown below (use the / (cursor left/
right) soft keys to go to the previous/next menu screen).
Press repeatedly to choose between:
ANALOG – Selects an analog signal.
– Selects an i.LINK signal.
DIGITAL – Selects an optical or coaxial digital signal.
2 RF – Selects a 2 RF signal.
AUTO – This is the default setting. The amplifier
selects the first available signal in the following
order: ; 2 RF; DIGITAL; ANALOG.
Note
If no digital inputs (including the 2 RF input) are
assigned for the current source, the input signal type
will default to ANALOG.
When using DIGITAL IN terminals the following
digital signal formats are supported: Dolby Digital,
DTS and PCM (32, 44.1, 48, 88.2 and 96 kHz sampling
frequencies). If you are using the i.LINK connectors,
DVD-A (including 176.4/192 kHz) and SACD are also
supported. If your source is not supported, select
ANALOG.
Some DVD players don’t output DTS signals. For
more details, refer to the instruction manual supplied
with your DVD player.
Even when i.LINK is selected and the i.LINK indicator
lights, you won’t hear any sound if the output settings
of your i.LINK device are off.
The audio signal from karaoke microphones and
some LDs is not output from the digital outputs.
Select ANALOG to listen to these formats.
LISTENING
MODE
AMPLIFIER
AMPLIFIER 1/3
STREAM
DIRECT
ACOUSTIC
CAL.
SIGNAL
SELECT
ADVANCED
CINEMA
ADVANCED
CONCERT
STEREO
STANDARD THX
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
SB CH
MODE
DIGITAL IN
S-VIDEO VIDEO
VIDEO INPUT
AUDIOLR
MIDNIGHT
LOUDNESS OPTIONTONE DIGITAL NR INPUT ATT
SELECT
CH LEVEL
ACOUSTIC
CAL.
AMPLIFIER
LISTENING
MODE
AMPLIFIER
AMPLIFIER 1/3
STREAM
DIRECT
ACOUSTIC
CAL.
SIGNAL
SELECT
ADVANCED
CINEMA
ADVANCED
CONCERT
STEREO
STANDARD THX
PHONES
SP SYSTEM
A/B
SIGNAL
SELECT
VIDEO
SELECT
TAPE2
MONITOR
STREAM
DIRECT
SETUP
MIC
SB CH
MODE
DIGITAL IN
S-VIDEO VIDEO
VIDEO INPUT
AUDIOLR
MIDNIGHT
LOUDNESS OPTIONTONE DIGITAL NR INPUT ATT
SELECT
CH LEVEL
ACOUSTIC
CAL.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSA-AX10i-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSA-AX10i-S in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSA-AX10i-S

Pioneer VSA-AX10i-S User Manual - English - 25 pages

Pioneer VSA-AX10i-S User Manual - German - 104 pages

Pioneer VSA-AX10i-S User Manual - Dutch - 104 pages

Pioneer VSA-AX10i-S User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info