611807
5
Zoom out
Zoom in
Previous page
1/16
Next page
Connecting up 02
5
En
Chapter 2:
Connecting up
Making cable connections
CAUTION
Before making or changing the connections, switch off the power and disconnect the power cord from the AC
outlet.
Connect the power cord after all the connections between devices have been completed.
AC IN
SPEAKERS
RECORDER
INININ
L
R
IN
SIGNAL
GND
OUT
PHONO
(
MM
)FM/DAB
ANTENNA
SACD/CD
NETWORK
B
RL
RL
A
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
Important
•The SIGNAL GND terminal is provided to reduce
noise when connecting the unit to components
such as an analog turntable.
Do not connect the PHONO (MM) terminals to any
component other than a turntable; also, do not
connect to a turntable equipped with built-in
equalizer. An excessively high sound output may be
produced, resulting in damage to your speakers or
other devices.
The unit’s PHONO (MM) terminals are designed to
be used with turntables equipped with MM
(moving-magnet) type cartridges. Turntables
equipped with MC (moving-coil) cartridges cannot
be used.
Make sure not to bend the cables over the top of
this unit (as shown in the illustration). If this
happens, the magnetic field produced by the
transformers in this unit may cause a humming
noise from the speakers.
If your turntable has a grounding wire, secure it to
the ground terminal on this receiver.
Note
When connecting a tape cassette deck, playback
noise may be heard, depending on the installation
location. This noise is caused by leakage flux from
the receiver’s transformer. In this event, change the
installation location, or move the deck farther from
the receiver.
Connecting audio cables
Connect the white plug to the left (L) jack, and the red
plug to the right (R) jack. Be sure to insert the plugs fully
into the jacks.
Connecting speaker cables
1 Twist the cable cores.
2 Loosen the nut on the
SPEAKERS
terminal, and insert the speaker cable into
the exposed hole in the terminal shaft.
3 Retighten the terminal nut.
CAUTION
When using only one set of speaker terminals
(SPEAKERS A or SPEAKERS B), the speaker used
should have a nominal impedance between 4
and 16 . When using both sets of terminals,
the connected speakers should have nominal
impedance between 8 and 16 . Consult the
instructions accompanying your speakers for
details regarding the impedance value.
Make sure the positive and negative (+/–) terminals
on the receiver match those on the speakers.
These speaker terminals carry HAZARDOUS live
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker
terminal. If any of the bare speaker wire touches the
back panel it may cause the power to cut off as a
safety measure.
L
R
Left (white)
Right (red)
12 3
10 mm
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SX-20DAB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SX-20DAB in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SX-20DAB

Pioneer SX-20DAB User Manual - German - 16 pages

Pioneer SX-20DAB User Manual - Dutch - 16 pages

Pioneer SX-20DAB User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info