491890
3
Zoom out
Zoom in
Previous page
1/28
Next page
English
Français
Italiano
Español
Nederlands
Deutsch
3
En
Connecting up (continued)
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for
ventilation to improve heat radiation (at least 40 cm at top, 10 cm at rear,
and 20 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure
reliable operation of the product, and to protect it from overheating. To
prevent fire hazard, the openings should never be blocked or covered with
items (such as newspapers, table-cloths, curtains) or by operating the
equipment on thick carpet or a bed.
D3-4-2-1-7b*_A1_En
STEREO RECEIVER
VOLUME
TUNE
/
PRESET
MEMORY
STANDBY
A
SPEAKERS
B
PHONES
TONE
BALANCE
S
X
-
20
STANDBY
ON
Connecting the speakers
Make sure you connect the speaker on the right to the right (R) terminal
and the speaker on the left to the left (L) terminal. Also make sure the
positive and negative (+/–) terminals on the receiver match those on the
speakers.
1
Twist the cable cores.
2
Loosen the nut on the SPEAKERS terminal, and insert the speaker
cable into the exposed hole in the terminal shaft.
3
Retighten the terminal nut.
12 3
10 mm
CAUTION
When using only one set of speaker terminals (SPEAKERS A or
SPEAKERS B), the speaker used should have a nominal impedance
between 4
Ω
and 16
Ω
. When using both sets of terminals, the
connected speakers should have nominal impedance between 8
Ω
and 16
Ω
. Consult the instructions accompanying your speakers
for details regarding the impedance value.
These speaker terminals carry
HAZARDOUS live voltage
. To prevent
the risk of electric shock when connecting or disconnecting the
speaker cables, disconnect the power cord before touching any
uninsulated parts.
Connecting the FM and AM antennas
Connect FM wire antenna and the the AM loop antenna
as shown below.
AM LOOP
FM UNBAL
75
ANTENNA
To power outlet
Connecting your equipment
Connecting the playback components
1
Connect the audio outputs of your SACD player (or CD player) to the
SACD/CD IN jacks on this receiver.
2
Connect the audio outputs of your network audio player to the
NETWORK IN jacks on this receiver.
You may connect other audio components furnished with analog audio
output jacks. If you wish to connect a portable audio player or other
component furnished with mini-plug output jacks (or headphone jacks),
use of a commercially available conversion plug will be necessary.
Connecting the cassette deck
Connect the audio outputs of your cassette deck (or other recorder)
to the RECORDER IN jacks on this receiver. Then connect the audio
inputs on the cassette deck to the RECORDER OUT jacks on this
receiver.
This will allow you to make recordings from the components connected to
this receiver.
Connecting a turntable
Connect the audio outputs of your turntable to the PHONO IN jacks
on this receiver.
Important
The
SIGNAL GND
terminal is provided to reduce noise when
connecting the unit to components such as an analog turntable.
Do not connect the
PHONO (MM)
terminals to any component other
than a turntable; also, do not connect to a turntable equipped with
built-in equalizer. An excessively high sound output may be produced,
resulting in damage to your speakers or other devices.
The unit’s
PHONO (MM)
terminals are designed to be used with
turntables equipped with MM (moving-magnet) type cartridges.
Turntables equipped with MC (moving-coil) cartridges cannot be used.
Plugging the receiver
Only plug in after you have connected all your components to this receiver,
including the speakers.
1
Plug the supplied power cord into the AC IN socket on the back of
the receiver.
2
Plug the other end into a power outlet.
AC IN
CAUTION
Handle the power cord by the plug part. Do not pull out the plug by
tugging the cord, and never touch the power cord when your hands are
wet, as this could cause a short circuit or electric shock. Do not place
the unit, a piece of furniture, or other object on the power cord or pinch
the cord in any other way. Never make a knot in the cord or tie it with
other cables. The power cords should be routed so that they are not
likely to be stepped on. A damaged power cord can cause a fire or give
you an electric shock. Check the power cord once in a while. If you find
it damaged, ask your nearest Pioneer authorized independent service
company for a replacement.
SX-20_YXE8_book.indb 3SX-20_YXE8_book.indb 3 2012/08/03 9:33:402012/08/03 9:33:40
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SX-20-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SX-20-K in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 11,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SX-20-K

Pioneer SX-20-K User Manual - English - 15 pages

Pioneer SX-20-K User Manual - German - 15 pages

Pioneer SX-20-K User Manual - Dutch - 15 pages

Pioneer SX-20-K User Manual - French - 15 pages

Pioneer SX-20-K User Manual - Italian - 15 pages

Pioneer SX-20-K User Manual - Spanish - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info