612929
9
Zoom out
Zoom in
Previous page
1/26
Next page
9
By pushing the push switch in the right transmitter for more than
3 seconds, the LEDs on the right transmitter blink green. When
communication with the left transmitter is enabled, the LEDs on
the left and right transmitters rapidly blink orange. Confirm that
the LEDs on the left and right transmitters blink when the mode
is switched. (If they do not blink, the communication may have
been done with another pedaling monitor sensor by mistake.
Move somewhere away from the other bicycles and do the
operation again.)
While the blinking takes place rapidly for 10 seconds, push the
switch again during that time for more than 3 seconds. The mode
is switched to the dual power meter mode. When the mode is
switched, the LED starts lighting orange for 10 seconds. If you do
not push long while the LEDs are rapidly blinking orange , it is
canceled and so, you must do the operation again.
•It may take several seconds to switch the sensor mode
depending on the radio transmission conditions.
If the pairing with the left transmitter fails, the LEDs of the right
transmitter blink red 5 times. Since the left transmitter may be in
the pedaling monitor mode, switch to the
single power meter mode first on Cyclocomputer SGX-CA500
and do the above operation. If it still fails, remove the batteries
from the left and right transmitters; wait for more than one
minute. Place the batteries back and do the operation again.
After the mode is switched, install the right transmitter cover
and tighten the screws to fix it in place. Use a tool that can
measure the torque to tighten the screws.
•Tightening torque: 30 cN·m
・install the transmitter cover and the screws in firmly to ensure
water resistant performance.
防水性能を保つため、送信機カバーおよびネジは確実に取り
付けてください。
・•Do not lose the water-proof packing.
For how to pair with the cyclocomputer, when using SGX-CA500,
refer to Page 24 and if using a cyclocomputer
From another manufacturer, refer to the User's Manual of that
cyclocomputer
.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SGY-PM910H2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SGY-PM910H2 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SGY-PM910H2

Pioneer SGY-PM910H2 User Manual - English, German, Dutch, French, Italian, Spanish - 234 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info