612929
4
Zoom out
Zoom in
Previous page
1/26
Next page
4
1 Preparations
1.1 Confirm the products
The operations necessary to install the Pedaling Monitor System on the customer’s bicycle depend on which System it
is; SGY-PM910HL/HR or SGY-PM910H2, and on which cycle computer is being used; SGX-CA500, SGX-CA900, or
some other manufacturer’s product.
1.2 Outline of procedure
1.2.1 For the SGY-PM910HL/HR with an ANT+ cycle computer
Single Power Meter Mode:(SGY-PM910Hl/HR Factory Default Mode)
1. [3.1Temporarily affix the Magnet]: Attach the magnet to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should flash
Orange for ten seconds
3. [3.2 Magnet Detection]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the
magnet.
4. [3.3.3 Fixing the Magnet]: Fix the magnet in place.
5. [4 Pairing with the Cyclocomputer]: Pair the sensor with the cycle computer.
6. [5 Zero Calibration]: Carry out Zero Calibration.
1.2.2 For the SGY-910H2/(HL+HR) with an ANT+ cycle computer
Dual Power Meter Mode:(SGY-PM910H2 Mode on shipment from Installation center)
1. [3.1Temporarily affix the Magnet]: Attach the left and right magnets to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should light
Orange for ten seconds.
3. [2.2 Mode Switching]: If the LED flashed in step 2, it is necessary to switch the mode to Dual Power Meter
Mode.
Push the button on the right side transmitter for two seconds, and the LED will flash quickly in Orange for ten
seconds. While this is happening, release the button and press it again for two seconds. The LED will then light in
Orange for ten seconds.
4. [3.2.2Detecting the Magnet Position]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the magnet.
5. [3.3.3Fixing the Magnets]: Fix the magnet in place.
6. [4Pairing with the Cyclocomputer]: Pair the sensors with the cycle computer using the device number of the
right side sensor.
7. [5Zero Calibration]: Carry out Zero Calibration.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SGY-PM910H2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SGY-PM910H2 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SGY-PM910H2

Pioneer SGY-PM910H2 User Manual - English, German, Dutch, French, Italian, Spanish - 234 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info