612929
21
Zoom out
Zoom in
Previous page
1/234
Next page
21
EN
Getting Started
Switch to dual power meter mode
By pushing the push switch in the right
transmitter for more than 3 seconds,
the LEDs on the right transmitter blink
green. When communication with the
left transmitter is enabled, the LEDs on
the left and right transmitters rapidly
blink orange.
Conrm that the LEDs on the left and
right transmitters blink when the mode
is switched. (If they do not blink, the
communication may have been done
with another pedaling monitor sensor
by mistake. Move somewhere away
from the other bicycles and do the
operation again.)
While the blinking takes place rapidly
for 10 seconds, push the switch
again during that time for more than
3 seconds. The mode is switched to
the dual power meter mode. When
the mode is switched, the LED starts
lighting orange for 10 seconds. If you
do not push long while the LEDs are
rapidly blinking orange , it is canceled
and so, you must do the operation
again.
It may take several seconds to switch
the sensor mode depending on the
radio transmission conditions.
If the pairing with the left transmitter
fails, the LEDs of the right transmitter
blink red 5 times. Since the left
transmitter may be in the pedaling
monitor mode, switch to the
single power meter mode rst on
Cyclocomputer SGX-CA500 and do
the above operation. If it still fails,
remove the batteries from the left and
right transmitters, wait for more than
one minute. Place the batteries back
and do the operation again.
After the mode is switched, install the
right transmitter cover and tighten the
screws to x it in place. Use a tool that
can measure the torque to tighten the
screws.
Tightening torque: 30 cN·m
Install the transmitter cover and
the screws in rmly to ensure water
resistant performance.
Do not lose the water-proof packing.
For how to pair with the cyclocomputer,
when using SGX-CA500, refer to Page
24 and if using a cyclocomputer
from another manufacturer, refer to the
User's Manual of that cyclocomputer.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SGY-PM910H2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SGY-PM910H2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SGY-PM910H2

Pioneer SGY-PM910H2 Installation Guide - English - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info