536830
106
Zoom out
Zoom in
Previous page
1/139
Next page
106
 
 
 
 
12
The System Setup and Other Setup menus
ZONE Setup
The volume setting and tone for the sub zones that can be used with this receiver can be changed and adjusted
here.
CAUTION
! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals
is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may
be produced even when Volume Level is set to –40 dB Fixed.
1 Select ‘ZONE Setup’ from the Other Setup menu.
2 Select ‘MAIN/HDZONE’, then press ENTER.
3 Set how the HDMI OUT 3 terminal is to be used.
! MAIN: Select this to output the same input source as in the main zone.
After setting this to MAIN, exit the home menu, then press HDMI OUT and select the terminal for HDMI
output (page 82).
! HDZONE (default): Use the HDMI output’s multizone function (HDZONE) to output an input source different
from the one in the main zone (page 80).
4 Press RETURN.
5 Select ‘ZONE 2’ or ‘ZONE 3’, then press ENTER.
6 Select the Volume Level setting you want.
When making multi-zone connections using the AUDIO ZONE 2 OUT or AUDIO ZONE 3 OUT terminals and per-
forming playback in Zone 2 or Zone3, you can set whether to adjust the Zone 2 or Zone3 volume on the receiver or
to fix it to a specific volume (–40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment from the factory,
allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from the connected
amplifier, make the setting below.
For ZONE 2, this setting is not possible if multi-zone settings have been made using the speaker terminals and
Speaker System is set to 7.1ch + ZONE 2. In this case, adjust the volume for the sub zones on the receiver.
! Variable (default) – The Zone 2/Zone3 volume is adjusted from the receiver.
! –40 dB Fixed/0 dB Fixed – The Zone 2/Zone 3 volume level output from the receiver is fixed to the value set
here.
7 Select the Power ON Level setting you want.
The sub zone volume is set to the volume selected here when the sub zone is turned on using the multi-zone func-
tion. Zones 2 and 3 can be set separately.
When Volume Level is set to –40 dB Fixed or 0 dB Fixed, the volume is fixed to that level, so the volume cannot
be set here.
! LAST (default) – When MULTI-ZONE is turned on, the volume is set to the level set the last time you were
listening to that zone.
!---” – When MULTI-ZONE is turned on, the volume for that zone is set to the minimum.
! –80.0dB to 0dB – When MULTI-ZONE is turned on, the volume is set to the level set here. The volume can be
set up to the value set at Volume Limit below.
8 Select the Volume Limit setting you want.
The maximum volume for the zone selected in step 5 can be set.
! OFF (default) – The maximum volume is not limited.
! –20.0dB/–10.0dB – The maximum volume is limited to the value set here.
9 Select the Mute Level setting you want.
The mute level for the zone selected in step 5 can be set.
This sets how much the volume is to be turned down when MUTE is pressed.
! FULL (default) – No sound.
! –40.0dB/–20.0dB – The volume will be turned down to the level specified here.
10 Adjust Lch Level and Rch Level.
The channel level for the zone selected in step 5 can be set.
The level can be adjusted between –12.0dB and +12.0dB, in 1 dB steps.
11 Select the HPF (High Pass Filter) setting you want.
This can only be set when ZONE 2 is selected in step 5.
The low frequency component output from the AUDIO ZONE 2 OUT terminals is cut. When a subwoofer is con-
nected in Zone 2, we recommend setting this to “ON”. This is only valid when Zone 2 is connected using the
AUDIO ZONE 2 OUT terminals.
! OFF (default) – The High Pass Filter function is disabled.
! ON – The High Pass Filter function is enabled.
12 Select the TONE setting you want.
This can only be set when ZONE 2 is selected in step 5.
The bass and treble for ZONE 2 can be adjusted. When BYPASS is selected, the original sound is played as such.
When ON is selected, the BASS and TREBLE can be adjusted.
! When the speaker terminals are being used for ZONE 2, the ZONE 2 TONE effect is valid when
Speaker System is set to 7.1ch FH/FW + ZONE 2, 5.1ch Bi-Amp + ZONE 2 or 5.1ch + ZONE 2+3. When set
to 7.1ch + ZONE 2, Multi-ZONE Music, the ZONE 2 TONE effect is not applied.
13 Adjust the bass (BASS) and treble (TREBLE) to your tastes.
This can only be set when ZONE 2 is selected in step 5 and ON is selected in step 12.
The BASS and TREBLE can each be adjusted between –10.0dB and +10.0dB, in 1 dB steps.
14 When you’re finished, press RETURN.
You will return to the Other Setup menu.
On Screen Display Setup
When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over
the video output on the display. This status display can be turned off by switching this setting to OFF.
! Default setting: ON
1 Select ‘On Screen Display Setup’ from the Other Setup menu.
2 Select the On Screen Display setting you want.
3 When you’re finished, press RETURN.
You will return to the Other Setup menu.
Notes
! The on-screen display is not displayed for video signals output from any terminals other than HDMI OUT 1 and
HDMI OUT 2.
! Depending on the type of video input signal (4K, 3D, etc.), the on-screen display may not be displayed.
! The size of the characters displayed differs according to the output resolution.
106


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SC-LX87 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-LX87 in the language / languages: English as an attachment in your email.

The manual is 6,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-LX87

Pioneer SC-LX87 Quick start guide - English, German - 48 pages

Pioneer SC-LX87 User Manual - German - 143 pages

Pioneer SC-LX87 Quick start guide - Dutch - 48 pages

Pioneer SC-LX87 User Manual - Dutch - 142 pages

Pioneer SC-LX87 Quick start guide - French - 48 pages

Pioneer SC-LX87 User Manual - French - 140 pages

Pioneer SC-LX87 Quick start guide - Italian - 48 pages

Pioneer SC-LX87 User Manual - Italian - 140 pages

Pioneer SC-LX87 Quick start guide - Spanish - 48 pages

Pioneer SC-LX87 User Manual - Spanish - 140 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info