Manual Pioneer SC-LX79 (page 138 of 151) (English)

611788

138

Zoom out

Zoom in

1/151

138

Additional information

Dolby Atmos format

Input signal format

Auto Surround / PURE DIRECT / DIRECT

ALC

Rendering Mode :

OBJECT

Rendering Mode :

LEGACY

When 6 or more speakers, excluding the subwoofers, are connected

Dolby Atmos

Channel decode Channel decode

When 5 or fewer speakers, excluding the subwoofers, are connected

Dolby Atmos Channel decode Channel decode Channel decode

Speaker Setting Guide

In order to achieve an even better surround effect, it is important to accurately position the speakers and make

their volume and tone characteristics uniform so as to finely focus the multi-channel sound.

The three major elements in positioning the speakers are distance, angle and orientation (the direction in

which the speakers are pointing).

Distance: The distance of all the speakers should be equal.

Angle: The speakers should be horizontally symmetrical.

Orientation: The orientation should be horizontally symmetrical.

In most homes, however, it is not possible to achieve this environment. For the distance, on this receiver it is pos-

sible to automatically correct the speaker distance electrically to a precision of 1 cm using the Full Auto MCACC

Setup function (page 59 ).

Step 1: Speaker layout and distance adjustment

Use speaker stands or the like to make sure the speakers are steady, and leave at least 10 cm from the surround-

ing walls. Position the speakers attentively so that the speakers on the left and right are at equal angles from the

listening position (center of the adjustments). (We recommend using cords, etc., when adjusting the layout.)

Ideally all the speakers should be equidistant from the listening position.

Note

If the speakers cannot be set at equal distances (on a circle), use the Auto MCACC Setup speaker distance cor-

rection and Fine Speaker Distance functions to make them equalize the distance artificially.

Step 2: Adjusting the speaker height

Adjust the heights (angles) of the different speakers.

Adjust so that the front speaker units reproducing mid- and high frequencies is roughly at the height of the ears.

If the center speaker cannot be set at the same height as the front speakers, adjust its angle of elevation to point

it to the listening position.

Set surround speaker 1 so that it is not under the height of the ears.

Step 3: Adjusting the speaker orientation

If the left and right speakers are not pointing in the same direction, the tone will not be the same on the right

and left, and as a result the sound field will not be reproduced properly. However, if all the speakers are pointed

towards the listening position, the sound field will seem cramped. Testing by the Pioneer Multi-channel Research

Group has shown that a good sense of sound positioning can be achieved by pointing all the speakers towards an

area 30 cm to 80 cm behind the listening position (between the surround speakers and the listening position).

However, the sense of sound positioning can differ according to the conditions in the room and the speakers

being used. In smaller environments in particular (when the front speakers are close to the listening position),

with this method the speakers will be pointed too inward. We suggest you use this example of installation as

reference when trying out different installation methods.

Step 4: Positioning and adjusting the subwoofer

Placing the subwoofer between the center and front speakers makes even music sources sound more natural (if

there is only one subwoofer, it doesn’t matter if it is placed on the left or right side). The low bass sound output

from the subwoofer is not directional and there is no need to adjust the height. Normally the subwoofer is placed

on the floor. Put it in a position at which it will not cancel out the bass sound output from the other speakers.

Also note that placing it near a wall may result in sympathetic vibrations with the building that could excessively

amplify the bass sound.

If the subwoofer must be installed near a wall, place it at an angle so that it is not parallel to the wall surface. This

can help reduce any sympathetic vibrations, but depending on the shape of the room this could result in stand-

ing waves. However, even if standing waves are generated, their influence on the sound quality can be prevented

using the Auto MCACC’s standing wave control function (page 107 ).

Step 5: Default settings with the Auto MCACC Setup (auto sound field

correction) function

It is more effective to perform the Full Auto MCACC Setup (page 59 ) procedure once the adjustments described

above have been completed.

Note

The distance to the subwoofer may be slightly larger than the distance actually measured with a tape measure,

etc. This is because this distance is corrected for electric delay, and is not a problem.

Positional relationship between speakers and monitor

Position of front speakers and monitor

The front speakers should be as equidistant as possible to the monitor.

45° to 60°

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-LX79 in the language / languages: English as an attachment in your email.

The manual is 9,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-LX79

Pioneer SC-LX79 Quick start guide - English, German - 76 pages

Pioneer SC-LX79 User Manual - German - 158 pages

Pioneer SC-LX79 Quick start guide - Dutch - 76 pages

Pioneer SC-LX79 User Manual - Dutch - 155 pages

Pioneer SC-LX79 Quick start guide - French - 76 pages

Pioneer SC-LX79 User Manual - French - 155 pages

Pioneer SC-LX79 Quick start guide - Italian, Spanish - 76 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer SC-LX79 Manual

Product: