699655
180
Zoom out
Zoom in
Previous page
1/223
Next page
180
Front Panel Rear Panel Remote
Contents
Connections
Playback
Setup
Full Auto MCACC
Place the supplied speaker setup microphone in the listening position, measure
the test tones emitted by the speakers, then the unit automatically sets the
optimum volume level for each speaker, the crossover frequencies, and the
distance from the listening position. The inuence of standing waves can be
reduced to suit the listening environment, the reverberation characteristics can be
measured to increase the precision of calibration, the speaker equalizers can be
adjusted, and the difference in phase and timing between speakers and speaker
units can be corrected. These settings and calibrations can be readjusted with
Manual MCACC, and you can enable or disable them in AV Adjust.
Calibration takes between 3 and 12 minutes to be completed. The speakers
emit the test tone at high volume during measurement, so be careful of your
surroundings. Keep the room as quiet as possible during measurement.
If you connect a subwoofer, check the power and volume of the subwoofer.
Set the subwoofer volume to more than half.
If the power of this unit suddenly turns off, the wires in the speaker cables
have touched the rear panel or other wires, and the protection circuit is
working. Twist the wires again securely, and make sure they do not stick out of
the speaker terminals when connecting.
1. Select the connected speaker conguration.
Height 1 Speaker
Height 2 Speaker
Top Middle
2 ch
---
Speaker B
Zone 2 Preout
Zone 2
7.1.2 ch
Zone Speaker
Note that the image on the screen changes each time you select the number
of channels in "Speaker Channels".
2. Place the supplied speaker setup microphone at the listening position, and
connect it to the SETUP MIC jack on the main unit.
SETUP MI
C
When placing the speaker setup microphone on a tripod, refer to the
illustration.
3. Conrm a test tone is output from the subwoofer and press ENTER.
4. Press ENTER. Then, test tones are output from each speaker, and the
connected speakers and the noise in the surrounding environment are
automatically measured.
5. The measurement results in step 4 are displayed. If there is no problem in
the detection result of the speaker, select "Next" and press ENTER to output
the test tone again to automatically set the settings such as volume level,
crossover frequency, etc., to their optimum. (The test tone is automatically
output when 10 seconds has elapsed without any operation.)
When an error message is displayed or when the connected speakers
cannot be detected, perform re-measurement by selecting "Retry" and
pressing ENTER.
When it cannot be resolved by performing the re-measurement, conrm
if the speakers are connected correctly. If there is any problem with the
speaker connection, perform the connection after disconnecting the power
cord.
6. Once the measurement is completed, it is possible to perform the
measurement in 8 additional listening positions. To perform the measurement,
select "Next" and press ENTER, then follow the instructions. To not perform
the measurement, select "Finish (Calculate)" and press ENTER.
After each listening position is detected, select "Finish (Calculate)" and
press ENTER to complete the detection process.
7. Disconnect the speaker setup microphone.
180


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SC-LX704 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-LX704 in the language / languages: English as an attachment in your email.

The manual is 19,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-LX704

Pioneer SC-LX704 Quick start guide - English, German - 2 pages

Pioneer SC-LX704 User Manual - German - 223 pages

Pioneer SC-LX704 Quick start guide - Dutch - 2 pages

Pioneer SC-LX704 User Manual - Dutch - 223 pages

Pioneer SC-LX704 Quick start guide - French - 2 pages

Pioneer SC-LX704 User Manual - French - 223 pages

Pioneer SC-LX704 Quick start guide - Italian - 2 pages

Pioneer SC-LX704 User Manual - Italian - 223 pages

Pioneer SC-LX704 Quick start guide - Swedish - 2 pages

Pioneer SC-LX704 User Manual - Swedish - 223 pages

Pioneer SC-LX704 Quick start guide - Spanish - 2 pages

Pioneer SC-LX704 User Manual - Spanish - 223 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info