611790
11
Zoom out
Zoom in
Previous page
1/76
Next page
11
The center speaker or rear speaker does not produce sound
Cause Solution
AUTO SURROUND
(mode that
outputs the number of input
channels as it is) is selected
upon 2-channel audio input
such as TV, music, etc.
To play a stereo sound source in multichannel, press the
SURR
button or the
ADV
button to select your favorite
mode.
Example) Press the
SURR
button several times to select
[
EXT.STEREO
].
The subwoofer does not produce sound
Cause Solution
The front speaker is set to
LARGE
.
(The low frequency component
will be produced from the
front speaker instead of the
subwoofer when 2-channel
audio input such as TV, music,
etc.)
To produce output from the subwoofer, change the speaker
setting. (There are two ways.)
Method 1
Change the front speaker to SMALL.
The low frequency component will be produced from
the subwoofer instead of the front speaker. When the
front speaker has a high capability to play low frequency
components, we recommend not to change.
Method 2
Change the subwoofer to PLUS.
The low frequency component of the front speaker will be
produced from both the front speaker and the subwoofer.
Therefore, the bass sound may be too powerful. In that
case, we recommend not to change or to change using
Method 1.
For the procedure to change, refer to the “Speaker Setting”
in the CD-ROM’s operating instructions.
HDMI, network, etc. operations become unresponsive
Cause Solution
The operations of this receiver
and connecting devices are
unresponsive.
Try resetting. To reset, turn off the power, and press down
the
STANDBY/ON
button on the front panel for 5 seconds
or more. (The power turns off in 5 seconds after the power
is turned on. The receiver’s setting will be maintained.)
Also try replugging the power cord of the connecting
devices.
To produce sound from TV
Refer to page 8 of the booklet to perform connection and setting.
To play, press the
TV
button to switch to TV input.
The remote control does not work
Cause Solution
The operation mode of
the remote control is not
switched.
When operating the receiver
Start the operation after pressing the
MAIN RECEIVER
button.
To operate functions such as network and iPod
Start the operation after pressing the button of each function
(
NET
,
iPod
, etc.).
If still not working, press the
MAIN RECEIVER
button first and
then press the button of each function.
2 TVs (projector) are connected but video and audio are sometimes
interrupted or not produced
Cause Solution
They may be interrupted or
not produced when affected
by the TV in power standby.
Press the
OUT P.
button and
/
button so that HDMI
output connected with that TV is not selected. Refer to
“Switching the HDMI output” in the CD-ROM’s operating
instructions for details.
The power suddenly turns off and the WIRELESS indicator flashes
Cause Solution
The core wire of the
speaker cord is touching
the rear panel, or touching
other core wires, and the
protection circuit is active.
Twist the conductive wire of the speaker cord once again, and
connect it so that it will not stick out from the speaker terminal
on the amplifier or speaker side.
Frequently asked questions
“Pioneer” is a trademark of Pioneer Corporation, and is used under license.
© 2015 Onkyo & Pioneer Corporation.
All rights reserved.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SC-LX59 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-LX59 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-LX59

Pioneer SC-LX59 User Manual - English - 149 pages

Pioneer SC-LX59 User Manual - Dutch - 153 pages

Pioneer SC-LX59 User Manual - French - 153 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info