577805
118
Zoom out
Zoom in
Previous page
1/140
Next page
118
FAQ
13
Symptom Remedy
Synchronized operation not possible
using Control with HDMI function.
Check the HDMI connections.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 74 ).
Turn the TV’s power on before turning on this receiver’s power.
Set the TV side Control with HDMI setting to on (see TV’s operating instructions).
Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to OUT 1. Then
turn on first the TV’s power, then this receiver’s power.
When HDZONE is set to ON, the
video resolution and number of
audio channels for the main zone
side changes.
This is due to the HDMI connection specifications; it is not a malfunction. When play-
ing the same input in the main zone and HDZONE, video and audio signals that can be
output in common for all the devices connected to the HDMI OUT 1, HDMI OUT 2 and
HDMI OUT 3 (HDZONE) terminals are set.
HDZONE cannot be turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 108 ).
When the input source for the main
or HDZONE is switched or when
the power of the respective zones is
turned on and off, the audio or video
of the HDMI output terminal that is
not being operated is sometimes
interrupted.
This is because the HDMI devices need to recognize each other again. This is not a
malfunction. If the picture is disturbed or not displayed, turn off the power of the devices
in all the zones, then try again. Also try temporarily turning the Network Standby and
Standby Through settings OFF.
Such menus as the HOME MENU as
well as the on-screen display are not
displayed for HDMI OUT 1 or HDMI
OUT 2.
Press OUT P. and switch the HDMI OUT 1/2 setting.
Cannot upscale to 4K or 1080p.
Change V.CONV to ON. (page 80 )
Change RES. (page 80 )
When HDZONE is turned on, upscaling cannot be performed. To perform upscaling, turn
off HDZONE (page 84 ).
4K video is not output even though a
4K compliant TV is connected.
When the MAIN/HDZONE setting is MAIN and the HDMI output setting is OUT 1+2 and
when the MAIN/HDZONE setting is HDZONE and HDZONE is the same input as with the
main zone, video is output with the lower resolution of the TV connected to HDMI OUT 1
and HDMI OUT 2. When there is only one 4K compliant TV, connect it to HDMI OUT 1
and set the HDMI output setting to OUT 1 or turn off HDZONE so that video is only output
to the 4K compliant TV.
Even though a 4K/60p 4:4:4 24 bit
compatible TV is connected, the
4K/60p 4:4:4 24 bit video image is not
output correctly.
Set the HDMI 4K/60p signal output setting to 4:4:4 (page 83 ).
When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission),
video images may not be output properly. In that case, replace the cable with a compat-
ible HDMI cable or change the HDMI 4K/60p signal output setting to 4:2:0 to watch the
4K/60p 4:2:0 24 bit video image.
The HDMI OUT 3 terminal does not output a 4K/60p 4:4:4 24 bit video image if
MAIN/HDZONE is set to HDZONE. Set MAIN/HDZONE to MAIN or use the HDMI OUT
1 or HDMI OUT 2 terminals.
You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 7 terminal. Use the
BD IN, HDMI IN 1 or HDMI IN 2 terminal.
MHL
Symptom Remedy
When playing an MHL-compat-
ible device connected to the
HDMI 7/MHL terminal, the Standby
Through function does not work and
the power turns off.
The MHL device will not operate unless power is being supplied from this receiver. When
this receiver is in the Standby Through mode, power cannot be supplied due to reduced
power consumption. Because of this, the MHL device will not operate. This is not a mal-
function.
MHL-compatible device cannot be
operated with the remote control.
Press MHL to set the remote control to the MHL control mode.
MHL POW ERR is displayed on the
display.
There is a problem with the power supply for the MHL device. After turning OFF the
receiver, disconnect the MHL device, connect the MHL device again and then turn ON
the power of the receiver.
If the error is displayed even though the above operation is repeated several times,
there is a problem with the receiver or the MHL device. Disconnect the power cable and
request repair.
Built-in AVNavigator
Symptom Cause Remedy
AVNavigator does not interact well
with the receiver.
The receiver’s power is not turned
on.
Turn the receiver’s power on. (Wait about 60
seconds after the power turns on for network
functions to start.)
The receiver or computer is not con-
nected to the LAN.
Connect a LAN cable to the receiver or computer
(page 42 ).
The router’s power is off. Turn the router’s power on.
Network connections could be
restricted due to the computer’s net-
work settings, security settings, etc.
Check the computer’s network settings, security
settings, etc.
In the middle of Wiring Navi, you are
instructed to turn off the power of the
unit and then connect other equip-
ment or speakers.
This is to avoid failure of the receiver
due to a short-circuit between cables
or from static electricity.
Per the Wiring Navi instructions, turn OFF the
power of the receiver. As long as the browser has
not quit, Wiring Navi resumes guidance upon
turning ON the receiver.
When the Wiring Navi or
Interactive Operation Guide is
launched, a warning about security
protection appears on the browser.
This is because of the browser’s
security function.
This is not a problem. Perform the operation to
authorize the blocked contents.
AVNavigator screen is not displayed
on the browser.
This receiver’s IP address has not
been entered into the browser cor-
rectly.
Check the receiver’s IP address and enter it cor-
rectly in the browser (page 106 ).
Receiver settings cannot be made
from a browser.
JavaScript is disabled on the internet
browser.
Enable JavaScript.
The browser is not compatible with
JavaScript.
Use an internet browser that is compatible with
JavaScript.
 
118


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SC-LX58-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-LX58-S in the language / languages: English as an attachment in your email.

The manual is 16,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-LX58-S

Pioneer SC-LX58-S Quick start guide - English, German - 76 pages

Pioneer SC-LX58-S User Manual - German - 147 pages

Pioneer SC-LX58-S Quick start guide - Dutch - 76 pages

Pioneer SC-LX58-S User Manual - Dutch - 145 pages

Pioneer SC-LX58-S Quick start guide - French - 76 pages

Pioneer SC-LX58-S User Manual - French - 144 pages

Pioneer SC-LX58-S Quick start guide - Italian - 76 pages

Pioneer SC-LX58-S User Manual - Italian - 143 pages

Pioneer SC-LX58-S Quick start guide - Spanish - 76 pages

Pioneer SC-LX58-S User Manual - Spanish - 143 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info