611801
104
Zoom out
Zoom in
Previous page
1/126
Next page
104
FAQ
13
Symptom Remedy
When playing a disc with the listen-
ing mode set to Auto Surround or
ALC, Pro Logic II or DTS Neo:X
does not appear on the receiver.
Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
page 56 ).
If a two channel soundtrack is currently playing (including Dolby Surround encoded),
then this is not a malfunction. Check the disc packaging for details about the audio
tracks available.
During playback of DVD-Audio, the
display shows PCM.
This will occur when playing DVD-Audio material over the HDMI connection. This is not
a malfunction.
The power turns off automatically
and some indicator flashes, or some
indicator flashes and the power does
not turn on.
See the Power section (page 100 ).
Remote control
Symptom Remedy
Cannot be remote controlled. Set the remote control unit’s remote control mode so that it matches the setting on the
main unit (see Operating multiple receivers on page 77 ).
Check whether the receiver’s remote control mode is properly set (see Remote Control
Mode Setup on page 94 ).
Try replacing the batteries in the remote control (see Loading the batteries on page 9 ).
Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel
(see Operating range of remote control unit on page 10 ).
Check that there are no obstacles between the receiver and the remote control.
Make sure that there is no fluorescent or other strong light shining on to the remote
sensor.
Other components can’t be operated
with the system remote.
If the battery ran down, the preset codes may have been cleared. Re-enter the preset
codes.
The preset code may be incorrect. Redo the procedure for entering preset codes.
When commands from the remote control units of other devices are registered using the
learning function, in some cases they may not be learned properly. In this case, register
the commands again using the learning function (see page 78 ). If they still do not work,
they may be in a special format that cannot be registered on this receiver’s remote con-
trol. Operate the device using another remote control.
HDMI
Symptom Remedy
The HDMI indicator blinks continu-
ously.
Check all the points below.
Video/audio is not output or is inter-
rupted.
This receiver is HDCP-compatible. Check that the components you are connecting are
also HDCP-compatible. If they are not, please connect them using the component or
composite video jacks.
Depending on the connected source component, it’s possible that it will not work with
this receiver (even if it is HDCP-compatible). In this case, connect using the component
or composite video jacks between source and receiver.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
If video images do not appear on your TV, try adjusting the resolution, Deep Color or other
setting for your component.
While analog video signals are being output over HDMI, use a separate connection for
audio output.
To output signals in Deep Color, use an HDMI cable (High Speed HDMI
®
/
TM
Cable) to
connect this receiver to a component or TV with the Deep Color feature.
The picture and sound output get cut
off, or there is no output produced.
Influence from a TV whose power is set to standby may cause the picture or sound output
to not be produced or to get cut off. In this case, press OUT P., and make sure to use an
output other than the HDMI output to which that TV is connected.
No picture.
Try changing the Resolution setting (in Setting the Video options on page 70 ).
To use the HDMI OUT 2 terminal in the main zone, set the MAIN/HDZONE
Output Setting to MAIN (page 95 ).
No sound, or sound suddenly
ceases.
Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 68 ).
If the component is a DVI device, use a separate connection for the audio.
If analog video is being output over HDMI, please use a separate connection for the
audio.
Check the audio output settings of the source component.
HDMI format digital audio transmissions require a longer time to be recognized. Due
to this, interruption in the audio may occur when switching between audio formats or
beginning playback.
Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,
or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-
rupted audio.
Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
HDCP ERROR shows in the display. Check whether or not the connected component is compatible with HDCP. If it is not
compatible with HDCP, reconnect the source device using a different type of connection
(component or composite). Some components that are compatible with HDCP still cause
this message to be displayed, but so long as there is no problem with displaying video,
this is not a malfunction.
 
104


Need help? Post your question in this forum.

Forumrules
1

Forum

pioneer-sc-1224

Reset search

  • I have an SC 1224 receiver. I have a couple of Sonos wifi speakers. I have a mesh wifi setup in my home from my internet connection. I would like to play music from the receiver over wifi to my speakers in other parts of the house. I.e. my music is on my phone, I connect my phone to the receiver via Bluetooth, the receiver will output to the speakers wired to it in the same room, a basic setup. Now if I want to extend that music to my wireless speakers in other parts of the house too far away for Bluetooth to reach, I should be able to use my home wifi network, but how do I get the receiver to 'talk' to my home wifi network so that it can pass a signal to my wireless speakers? Submitted on 16-6-2023 at 06:39

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer SC-1224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-1224 in the language / languages: English as an attachment in your email.

The manual is 7,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-1224

Pioneer SC-1224 Quick start guide - English, German - 76 pages

Pioneer SC-1224 User Manual - German - 133 pages

Pioneer SC-1224 Quick start guide - Dutch - 76 pages

Pioneer SC-1224 User Manual - Dutch - 130 pages

Pioneer SC-1224 Quick start guide - French - 76 pages

Pioneer SC-1224 User Manual - French - 129 pages

Pioneer SC-1224 Quick start guide - Italian, Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info