Manual Pioneer SC-1224 (page 72 of 126) (English)

611801

Zoom out

Zoom in

1/126

Using other functions

Switching the output (OUTPUT PARAMETER)

You can press OUT P. to switch the output of speaker terminals or HDMI terminals to be played.

Switching the speaker terminals

If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at Speaker system setting on page 90 , you can

switch between speakers using the OUT P. button. If you selected Front Bi-Amp, ZONE 2 or HDZONE, the button

will simply switch your main speaker terminals on or off.

1 Press OUT P..

! You can perform the same operation by pressing SPEAKERS on the front panel.

2 Use i/j to select ‘SP’.

3 Use k/l to switch the speaker terminals to be played.

As mentioned above, if you have selected Front Bi-Amp, ZONE 2 or HDZONE, the button will simply switch your

main speaker terminal (A) on or off.

Press repeatedly to choose a speaker terminal option:

When you select Normal(SB/FH), you can select from:

! SP: SB/FH ON – Surround back or front height channels are added to the front, center and surround chan-

nels (maximum 5 channels) and a maximum of 7 channels are output. The surround back and front height

channels are switched automatically according to the audio input signal.

! SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5

channels) and a maximum of 7 channels are output.

! SP: FH ON – Front height channels are added to the front, center and surround channels (maximum 5 chan-

nels) and a maximum of 7 channels are output.

! SP: OFF – No sound is output from the speakers (Pre-AMP mode).

When you select Normal(SB/FW), you can select from:

! SP: SB/FW ON – Surround back or front wide channels are added to the front, center and surround channels

(maximum 5 channels) and a maximum of 7 channels are output. The surround back and front wide channels

are switched automatically according to the audio input signal.

! SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5

channels) and a maximum of 7 channels are output.

! SP: FW ON – Front wide channels are added to the front, center and surround channels (maximum 5 chan-

nels) and a maximum of 7 channels are output.

! SP: OFF – No sound is output from the speakers (Pre-AMP mode).

When you select Speaker B, you can select from:

! SP: A ON – Sound is output from the A-speaker terminals (up to 7 channels (including surround back chan-

nels), depending on the source).

! SP: B ON – Sound is output from the two speakers connected to the B-speaker terminals. Multichannel

sources will not be heard.

! SP: A+B ON – Sound is output from the A-speaker terminals (up to 5 channels, depending on the source), the

two speakers connected to the B-speaker terminals, and the subwoofer. The sound from the B-speaker termi-

nals will be the same as the sound from the A-speaker terminals (multichannel sources will be downmixed to

2 channels).

! SP: OFF – No sound is output from the speakers (Pre-AMP mode).

Notes

! The subwoofer output depends on the settings you made in Manual speaker setup on page 90 . However, if

SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).

! All speaker systems (except Speaker B connections) are switched off when headphones are connected.

Switching the HDMI output

Set which terminal to use when outputting video and audio signals from the HDMI output terminals.

The HDMI OUT 1 terminal is compatible with the Control with HDMI function.

1 Press OUT P..

2 Use i/j to select ‘OUT 1/2’.

3 Use k/l to select the setting.

Please wait a while when Please wait ... is displayed.

The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed.

! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-

nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV’s remote

control.

! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2 (page 95 ).

Changing the channel level while listening

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor

when setting up a home theater system.

1 Press CH LV..

2 Use i/j to select the channel you wish to adjust.

3 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

4 When you’re finished, press RETURN.

Input Volume Absorber

This can be used to correct for the difference in volume between input sources.

1 Switch to the input whose volume you want to adjust.

2 Press CH LV..

3 Use i/j to select ‘ALL’.

4 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

5 When you’re finished, press RETURN.

I have an SC 1224 receiver. I have a couple of Sonos wifi speakers. I have a mesh wifi setup in my home from my internet connection. I would like to play music from the receiver over wifi to my speakers in other parts of the house. I.e. my music is on my phone, I connect my phone to the receiver via Bluetooth, the receiver will output to the speakers wired to it in the same room, a basic setup. Now if I want to extend that music to my wireless speakers in other parts of the house too far away for Bluetooth to reach, I should be able to use my home wifi network, but how do I get the receiver to 'talk' to my home wifi network so that it can pass a signal to my wireless speakers? Submitted on 16-6-2023 at 06:39
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer SC-1224 in the language / languages: English as an attachment in your email.

The manual is 7,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer SC-1224

Pioneer SC-1224 Quick start guide - English, German - 76 pages

Pioneer SC-1224 User Manual - German - 133 pages

Pioneer SC-1224 Quick start guide - Dutch - 76 pages

Pioneer SC-1224 User Manual - Dutch - 130 pages

Pioneer SC-1224 Quick start guide - French - 76 pages

Pioneer SC-1224 User Manual - French - 129 pages

Pioneer SC-1224 Quick start guide - Italian, Spanish - 76 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer SC-1224 Manual

Product: