574059
10
Zoom out
Zoom in
Previous page
1/94
Next page
Getting started02
10
En
1 Connect the microphone to the MCACC
MIC jack on the rear panel.
2 Place the microphone at your normal
listening position.
Place it about ear height, and make sure it is
level by using a table or chair.
Make sure there are no obstacles between the
speakers and the microphone.
3 If the system is off, press
STANDBY/ON to turn the power on.
If the tuner is selected, switch the input source.
4 Press SHIFT+MCACC.
Try to be as quiet as possible after pressing
SHIFT+MCACC
. The volume increases
automatically and the system outputs a series
of test tones.
Press
SHIFT+MCACC
to cancel and revert
to the previous Auto MCACC settings.
If the noise level is too high,
NOISY
blinks
in the display for five seconds. To exit and
check the noise levels
1
, press
SHIFT+MCACC
, or to try again, press
ENTER
when
RETRY
shows in the display.
If you see an
ERR MIC
or
ERR SP
message
in the display, there may be a problem with
your mic or the speaker connections. To try
again, press
ENTER
when you see
RETRY
2
.
When the MCACC setup is complete, the
volume level returns to normal and
COMPLETE
3
shows in the display, indicating
that the MCACC setup is complete and
Acoustic Calibration EQ has been activated.
4
Using the on-screen displays
For ease of use, this system makes extensive
use of graphical on-screen displays (OSDs).
All the screens are navigated in basically the
same way, using
,
,
,
to change the
highlighted item and pressing
ENTER
to select
it.
5
Important
Throughout this manual, ‘Select’ means
use the cursor buttons to highlight an item
on-screen, then press
ENTER
.
Tip
The button guide at the bottom of every
OSD screen shows you which buttons
you’ll need to use for that screen.
Note
1• If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles
blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air condition-
er, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.
• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto
MCACC setup.
2 If this doesn’t work, press
SHIFT+MCACC
, turn off the power, and check the problem indicated by the
ERR
message, then try
the Auto MCACC setup again.
AM LOOP
FM
UNBAL
75
S-VIDEO
VIDEO
COMPONENT
VIDEO
C
R
/
P
R
C
B
/
P
B
Y
IN
ANTENNA
VIDEO OUT
CONTROL
MCACC
MIC
3 If
COMPLETE
doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.
4 See
Listening with Acoustic Calibration EQ
on page 15 to switch on/off Acoustic Calibration EQ.
5 The screen saver will appear after five minutes of inactivity.
Button
What it does
HOME
MENU
Displays/exits the on-screen display

Changes the highlighted menu item
ENTER
Selects the highlighted menu item
RETURN
Returns to the main menu without
saving changes
XV-DV353_555.book 10 ページ 2006年4月7日 金曜日 午後6時18分
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer S-DV1SW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer S-DV1SW in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info