573928
71
Zoom out
Zoom in
Previous page
1/156
Next page
Using the GUIDE Plus+™ electronic program guide
05
71
En
Important
•A timer recording can’t be set if there are already 32
timer programs waiting to be recorded.
Timer recording will not start if:
– The recorder is already recording.
– A disc is being initialized, finalized or unfinalized.
Timer recording will start when the operation
preventing timer recording has finished.
The timer indicator ( ) lights in the front panel
display when the timer is active. If the indicator is
blinking it means that (for a DVD timer recording)
there is no disc loaded, or the disc loaded is not
recordable (for an HDD timer recording it means that
the HDD is not recordable).
Approximately two minutes before a timer recording
is set to start, the recorder will go into timer recording
standby. In timer recording standby you cannot use
some functions.
The maximum length for timer recordings made to
the HDD is 24 hours. However, because one title
(HDD) is limited to 12 hours, recordings over 12
hours will be spread over two titles. Note that there
will be a break in the recording of a few seconds
between titles.
VPS/PDC works only with analog stations; it does not
work with digital TV stations.
VPS/PDC may not work with all broadcast stations in
your country/area. Check with the stations for
compatibility.
The hours between 3:00 and 5:00 in the morning are
used by the GUIDE Plus+ system to download
program information. During these times, VPS/PDC
may not work reliably; leave VPS/PDC off if you set a
timer recording for these times.
Extending a timer recording in progress
You can extend a timer recording beyond the
programmed end time. This can be useful if a broadcast
program overruns, for example.
Canceling or extending the timer
1 Press and hold for three seconds during a
timer recording.
Recording continues, but the timer indicator disappears
from the front panel display indicating that the timer has
been canceled.
2 Press repeatedly to extend recording in 30
minute blocks.
Stopping a timer recording
1 Press during a timer recording.
2 Select ‘Yes’ to confirm.
Preventing use of the recorder before a timer
recording (child lock)
You can make all the front panel and remote control
buttons inoperative using the child lock feature. This is
useful when you set a timer recording and want to make
sure that the timer settings are not changed before
recording has finished.
1 If the recorder is on, switch it into standby.
2[Front panel] Press and hold for three seconds
to lock the controls.
The front panel display briefly shows LOCK. If any buttons
are pressed on the remote or front panel, LOCK is briefly
displayed again.
To unlock the recorder, press and hold STOP on
the front panel (while the recorder is stopped) for
three seconds until the display shows UNLOCK.
Frequently Asked Questions
Even though the timer is set, the recorder doesn’t start
recording!
Check that the disc loaded or HDD is recordable, not
locked (see Lock Disc on page 124), and that there are
fewer than 99/999 titles already on the DVD/HDD.
The recorder won’t let me enter a timer program! Why
not?
You can’t enter a timer program if the clock isn’t set.
What happens when two or more timer programs
overlap?
Basically, the program with the earlier recording start
time has priority. However, the recorder will start
recording the program with the later start time after
the earlier program is finished. If two programs have
the same times (but different channels, for example),
the program set most recently takes priority.
If VPS/PDC is active for two timer programs that are
programmed to start at the same time, then the
program that actually starts first takes priority.
REC
ì
REC
ì
STOP REC
ENTER
RECORDER
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer RCS-656HX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer RCS-656HX in the language / languages: English as an attachment in your email.

The manual is 9,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer RCS-656HX

Pioneer RCS-656HX User Manual - English - 156 pages

Pioneer RCS-656HX User Manual - Danish - 464 pages

Pioneer RCS-656HX User Manual - French - 155 pages

Pioneer RCS-656HX User Manual - Swedish, Finnish - 464 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info