573927
134
Zoom out
Zoom in
Previous page
1/152
Next page
The Initial Setup menu
15
134
En
Additional information about the TV system
settings
About the input line system
This recorder is compatible with PAL, SECAM, 3.58 NTSC
and PAL-60 TV systems. The Input Line System and Input
Colour System settings determine how the recorder
treats incoming video signals from an external input or
the built-in TV tuner.
Please note the following points when changing the
input line system:
When the current input is a built-in tuner channel
preset, changing the input line system will usually
also affect the input line system of the AV2 (INPUT 1/
DECODER) input. However if the AV2/L1 In setting is
set to Decoder, then the L2 input is affected instead.
If, when the Input Line System setting is changed, the
screen goes blank (due to incompatibility with your
TV), you can switch back by pressing and holding the
front panel STOP button then pressing OPEN/
CLOSE (also front panel) while the recorder is
stopped.
When you switch the Input Line System setting the
Copy List is erased. If you switch the setting using the
STOP button and OPEN/CLOSE buttons as
described above, there is no confirmation, so please
use with care.
You can’t mix recordings of different TV line systems
on the same disc.
When you change this setting, the Input Colour
System setting also changes (see below).
About NTSC on PAL TV
Depending on the Input Line System setting and the
NTSC on PAL TV setting, the signal format output when
the recorder is stopped varies as shown in the table
below.
Front Panel Display On • The time is shown in the front panel display when the recorder is in standby.
Off The front panel display is switched off in standby (although it still lights dimly
when setting a timer recording).
Remote Control
Mode
Recorder 1–3
(default: Recorder 1)
If you are using more than one recorder in the same room, set them to different
IDs. This setting sets the recorder ID; to change the remote controller ID, press
and hold RETURN then press 1, 2 or 3 to set. The remote will only control a
recorder with the same ID.
AV. Link This Recorder
Only •
Signals received through the AV input when the recorder is in standby are not
passed through to the AV output.
Pass Through Signals received when in standby are passed though to the output for connected
devices. (Note that during EPG data download, the EPG data is not passed
through.)
When set to Pass Through, make sure to set Power Save (page 128) to Off.
DivX VOD Registration Code Use to display the recorder’s DivX registration code. See DivX video compatibility
on page 47 and DivX® VOD content on page 47.
Set Preview
(HDD only)
Quick Preview • When in the Disc Navigator, the thumbnail video plays short excerpts from
throughout the selected title. (Note that edited titles that will play normally from
the beginning.)
Normal The thumbnail video plays from the beginning of the title.
Setting Options Explanation
Input Line
System
NTSC on PAL
TV
Output when
stopped
625 System Off PAL
On PAL
525 System Off NTSC
On PAL–60
134


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer RCS-606H-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer RCS-606H-S in the language / languages: English as an attachment in your email.

The manual is 5,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer RCS-606H-S

Pioneer RCS-606H-S User Manual - German - 156 pages

Pioneer RCS-606H-S User Manual - Dutch - 152 pages

Pioneer RCS-606H-S User Manual - French - 152 pages

Pioneer RCS-606H-S User Manual - Italian - 152 pages

Pioneer RCS-606H-S User Manual - Swedish - 298 pages

Pioneer RCS-606H-S User Manual - Spanish - 152 pages

Pioneer RCS-606H-S User Manual - Norwegian - 298 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info