492008
24
Zoom out
Zoom in
Previous page
1/167
Next page
24
En
02
Install Your Flat Panel TV
A common flat panel TV mounting option is to hang the panel on a sturdy wall or from a reinforced ceiling. When
mounting in this way, some preparations must be completed first. Follow the steps below to prepare the panel for
mounting.
1 ) Attach the speaker brackets to the speaker (see page 19).
2 ) Attach the speaker to the panel (see page 21).
3 ) Connect the speaker cables to the speakers then to the panel (see page 22).
4 ) Connect cables for any other devices to the panel.
When deciding on a location for your flat panel TV, consider other equipment in the room. Equipment such
as a DVR, Receiver, VCR, etc. requires some way to communicate with the panel, either directly or through
another device. Review the instructions that came with the other equipment for available ports and
terminals.
After deciding which ports and terminals are needed, mark the connections on the flat panel TV for easier
identification once the panel is mounted.
5 ) Temporarily bundle loose cables with rubber bands (not included).
6 ) Plug the flat panel TV’s power cord in to the panel but do NOT plug in to the power outlet.
7 ) Follow installation directions provided with your selected wall/ceiling mount.
For details, refer to the operating instructions supplied with the wall/ceiling mount unit.
2.4 Mount the Flat Panel TV
Because your flat panel TV is slim but heavy, have at least two people mount and/or position the panel. The
following sections provide instructions for the different mounting and anchoring options.
Anchor the Panel When Using a Stand
When using a stand, stabilize the panel to keep it from tipping over. Please use the supplied metal fittings and
screws to anchor the panel to a wall or other solid support structure.
Another option is to purchase hooks, cords, and fittings through your installer or from your local hardware store.
The hardware size and strength depends on the composition and thickness of the anchoring surface.
Recommended hook: Nominal diameter 8 mm (3/8 inch), length 12 mm to 18 mm (0.5 inches to 0.7 inches)
To anchor the panel when using the provided stand, follow the steps below.
1 ) Attach the hooks to the mounting holes on the
back of the panel.
2 ) Sink the fittings into the wall or support structure.
3 ) Run cords between the hooks and the fittings.
4 ) Tighten the cords until the panel is anchored but
not pulled off balance.
(PRO-111FD)
Fitting
2. Cord
1. Hook
12 mm to 18 mm
(0.5 inches to 0.7 inches)
M8
PRO151FD.book Page 24 Thursday, July 10, 2008 3:58 PM
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer PRO151FD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer PRO151FD in the language / languages: English as an attachment in your email.

The manual is 8,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info