455118
3
Zoom out
Zoom in
Previous page
1/12
Next page
3
English
English
MOUNTING THE SPEAKERS
TO YOUR PLASMA DISPLAY
NOTE:
The diagram depicts the mounting of the right
speaker. The left speaker mounts in the same way.
1. 1 Attach the speakers to the speakers mounting
bracket (top and bottom) with the speakers
mounting screws (M4 × 10 mm).
2 Remove the seals from the cushions and then
attach the cushions to the sides of the speakers
in the locations indicated in the diagram below.
Speakers Mounting
Screw (M4 × 10 mm)
Speakers Mounting
Screw (M4 × 10 mm)
Speaker Mounting
Bracket (For
RIGHT-TOP)
Speaker Mounting
Bracket (For RIGHT-
BOTTOM)
Tighten the bottom speaker
mounting bracket to the display
temporarily (one place bottom).
After passing the wide part of the
hole over the screw, lower the
speaker.
3. Hang the speaker mounting bracket on the screw
you installed at the top by passing the wide part
over it and lowering into the slot; screw in the
lower screw temporarily.
After passing the wide part of the hole of the speaker
mounting bracket (top) over the screw, lower the
speaker onto it.
2. Loosely attach the speakers mounting screws
(M5 × 10 mm) to the plasma display (one location
on the left and one on the right).
Do not tighten it all the way yet. Leave it loose, with
about 5 mm left to tighten.
4. Adjust the position of the speaker and then fix the
upper and lower screws firmly.
Adjust the positions of the speakers and the Plasma
Display so their top surfaces are the same height.
Adjust the positions of the speakers and the Plasma
Display so their side surfaces are parallel.
5. Tighten the two screws, at the top and bottom for
each speaker (total of four screws), thus fixing the
speakers to the display.
Top, Back of
Display
5 mm
Leave a space of about 5 mm
Speakers Mounting Screw
(M5 × 10 mm)
Speakers Mounting Screw
(M5 × 10 mm)
Speakers Mounting Screw
(M5 × 10 mm)
Speakers Mounting Screw
(M5 × 10 mm)
Speaker R
Speaker L
Cushion
Cushion
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer PDP-S51 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer PDP-S51 in the language / languages: English, French as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info