474291
21
Zoom out
Zoom in
Previous page
1/141
Next page
21
En
Watching TV
06
English
Watching TV
Unless you set up TV channels that you can watch under the
current conditions, you cannot tune in those channels. For the
procedure, see “Setting up TV channels automatically” on page
27.
Turning on/ off the power
NOTE
When the Media Receiver is plugged into a power outlet, it is
placed into the standby mode; the STANDBY indicator on its
front panel should flash red. The Media Receiver stays in the
standby mode unless it is unplugged from the power outlet.
To turn on the system, press POWER on the Plasma Display.
The POWER ON indicators on the Plasma Display and Media
Receiver light up in blue.
To turn off the system, press a on the remote control unit or
STANDBY/ON on the Media Receiver.
The Plasma Display and Media Receiver are placed into the
standby mode; their respective STANDBY indicators light up
in red.
You can then turn on the system again by pressing a or 0 to
9 on the remote control unit or STANDBY/ON on the Media
Receiver. If you press 0 on the remote control unit, images
come from the INPUT 1 source. If you press 1 to 9, TV images
display.
You can also press POWER on the Plasma Display to turn off
the system. However, you cannot then turn on the system
again by pressing the buttons on the remote control unit and
Media Receiver.
NOTE
If you are not going to use the Plasma Display System for a
long period of time, be sure to remove the power cord from
the power outlet.
When the system is placed into the standby mode, the main
power flow is cut and the system is no longer fully
operational. A minute flow of power feeds the system to
maintain operation readiness.
Plasma Display
Media Receiver
Plasma Display/Media Receiver status indicators
The table below shows the operational status of the Plasma
Display System. You can check the current status of the system
with the indicators on the Plasma Display and Media Receiver.
For other than the above, see “Troubleshooting” on page 46.
STANDBY indicator
POWER ON indicator
POWER
button
ON STANDBY
STANDBY
/
ON
PULL
OPEN
STANDBY indicator
POWER ON indicator
STANDBY/ON
Indicator Status System Status
Plasma Display Media Receiver
POWER ON STANDBY POWER ON STANDBY
The power cords of both the Plasma Display and the Media Receiver have been
disconnected. Or, the power cord of the Plasma Display has been connected but
the POWER button of the Plasma Display is off.
Power to the system is on.
The system is in the standby mode.
Flashing
The power cord of the Media Receiver has been disconnected.
Flashing
Power to the Plasma Display is off. Or the power cord of the Plasma Display has
been disconnected.
PDP-506FDE.book Page 21 Wednesday, June 29, 2005 4:00 PM
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer PDP-436FDE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer PDP-436FDE in the language / languages: English, German, French as an attachment in your email.

The manual is 8,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer PDP-436FDE

Pioneer PDP-436FDE User Manual - Dutch, Italian, Spanish, Spanish - 141 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info