491902
5
Zoom out
Zoom in
Previous page
1/116
Next page
Connecting up 02
5
En
English
DeutschFrançais
Nederlands
Italiano Español Русский
Chapter 2:
Connecting up
Caution
Before making or changing the connections,
switch off the power and disconnect the power cord
from the AC outlet.
Connect the power cord after all the connections
between devices have been completed.
Analog audio output connections
By connecting this unit’s analog audio output to the
analog audio input of an amplifier, you can use the
amplifier to enjoy analog audio produced from this unit.
Digital audio connections
Important
Care in the handling of optical fiber cables
Do not allow optical fiber cables to be bent at sharp
angles. When storing optical fiber cables, roll in
coils of at least 15 cm diameter.
When connecting optical fiber cables, align the
connectors correctly and insert fully. If the
orientation of the cable connector is incorrect and
excessive force is applied in the attempt to fasten
the connector, the connector may be deformed,
preventing the shutter from closing when the cable
is removed.
Digital audio output connections
If desired, the digital audio output from this unit can be
connected to an AV amplifier or digital recording device
(CD recorder, MD, etc.).
This unit’s DIGITAL OUT terminals do not output
sound from SACD and DSD discs, nor from iPod/
iPhone/iPad devices.
DIGITAL IN
ANALOG
RL
AUDIO INPUT
Amplifier
Audio cable (included)
PD-50’s rear panel
DIGITAL IN
DIGITAL IN
OPTICAL
DIGITAL IN
COAXIAL
AV amplifier or
digital recording
device
Optical fiber cable
(commercially
available)
Coaxial digital
audio cable
(commercially
available)
PD-50’s rear panel
AV amplifier or
digital recording
device
Note
For digital audio output, CDs played on this unit
must produce linear PCM signals with a sampling
rate up to 44.1 kHz and quantitative bits up to 16
bits (some discs may not be playable depending on
the connected component and environment). For
information about other files, see page 14.
Digital audio input connections
This unit can be used as a D/A converter by connecting
the digital audio output of a digital audio component to
the digital audio input of this unit.
See the section “Using this unit as a D/A converter
(page 12) for details about the audio output of signals
input to this unit’s DIGITAL IN terminals.
Note
This unit supports linear PCM signals with
sampling rates and quantitative bits up to 192 kHz/
24 bits (operation may not be possible in all cases,
depending on components connected and
operating environment).
Using centralized control with other
Pioneer components
This unit and other Pioneer components equipped with
CONTROL IN/OUT jacks can be controlled with a single
remote control by aiming the remote toward the signal
receptor on the AV amplifier or other component. This
also allows remote control of components not equipped
with a remote sensor, or installed in places where the
component’s remote sensor cannot be accessed.
Note
For connections use a commercially available
monaural miniplug cord (without resistor).
When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
not allow proper system control.
When a control cord is connected to the PD-50’s
CONTROL IN jack, the PD-50 cannot be controlled
by pointing the remote control at the unit's remote
sensor (the sensor is automatically disabled).
DIGITAL IN
DIGITAL IN
COAXIAL
DIGITAL IN
OPTICAL
Coaxial digital
audio cable
(commercially
available)
Optical fiber cable
(commercially
available)
PD-50’s rear panel
Digital audio 1
Digital audio 2
To other Pioneer
component equipped
with CONTROL IN jack
Remote control for
AV amplifier, etc.
Point the remote
control toward the
signal receiver on
the AV amplifier, etc.
Other Pioneer component
equipped with CONTROL
IN/OUT jacks
PD-50
PD-50_PWSYXZT8.book 5 ページ 2012年7月6日 金曜日 午前11時12分
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer PD-50-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer PD-50-K in the language / languages: English, German, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 24,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info