491903
5
Zoom out
Zoom in
Previous page
1/104
Next page
Connecting up 02
5
En
English
DeutschFrançais
Nederlands
Italiano Español Русский
Chapter 2:
Connecting up
Caution
Before making or changing the connections,
switch off the power and disconnect the power cord
from the AC outlet.
Connect the power cord after all the connections
between devices have been completed.
Analog audio output connections
By connecting this unit’s analog audio output to the
analog audio input of an amplifier, you can use the
amplifier to enjoy analog audio produced from this unit.
Digital audio output connections
If desired, the digital audio output from this unit can be
connected to an AV amplifier or digital recording device
(CD recorder, MD, etc.).
This unit’s DIGITAL OUT terminals do not output
sound from SACD and DSD discs, nor from iPod/
iPhone/iPad devices.
Important
Care in the handling of optical fiber cables
Do not allow optical fiber cables to be bent at sharp
angles. When storing optical fiber cables, roll in
coils of at least 15 cm diameter.
When connecting optical fiber cables, align the
connectors correctly and insert fully. If the
orientation of the cable connector is incorrect and
excessive force is applied in the attempt to fasten
the connector, the connector may be deformed,
preventing the shutter from closing when the cable
is removed.
Note
For digital audio output, CDs played on this unit
must produce linear PCM signals with a sampling
rate up to 44.1 kHz and quantitative bits up to 16
bits (some discs may not be playable depending on
the connected component and environment). For
information about other files, see page 12.
ANALOG
RL
AUDIO INPUT
Amplifier
Audio cable (included)
PD-30’s rear panel
DIGITAL IN
OPTICAL
DIGITAL IN
COAXIAL
AV amplifier or
digital recording
device
Optical fiber cable
(commercially
available)
Coaxial digital
audio cable
(commercially
available)
PD-30’s rear panel
AV amplifier or
digital recording
device
Using centralized control with other
Pioneer components (PD-30 only)
This unit and other Pioneer components equipped with
CONTROL IN/OUT jacks can be controlled with a single
remote control by aiming the remote toward the signal
receptor on the AV amplifier or other component. This
also allows remote control of components not equipped
with a remote sensor, or installed in places where the
component’s remote sensor cannot be accessed.
Note
For connections use a commercially available
monaural miniplug cord (without resistor).
When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
not allow proper system control.
When a control cord is connected to the PD-30’s
CONTROL IN jack, the unit cannot be controlled by
pointing the remote control at the PD-30 (the
remote sensor is automatically disabled).
Plugging in
Important
If it is necessary to detach the power cord, first be
sure to press the
/I
STANDBY/ON button on the
front panel of the unit so the PD-30 is turned OFF or
the PD-10 is in standby mode before detaching the
cord.
Confirm that the [-OFF-] indicator is not lighted in
the main unit’s front panel display before
disconnecting the power cord. If the power cord is
disconnected while the [-OFF-] indicator is still
lighted, the unit’s settings may revert to factory
defaults.
When going on a trip or otherwise not using the
unit for an extended period, always disconnect the
power cord from its outlet.
Caution
Do not use any power cord other than the one
supplied with this unit.
Do not use the supplied power cord for any purpose
other than that described below.
After you’ve finished making all connections, plug the
unit into an AC outlet.
1 Plug the supplied power cord into the
AC IN
socket on the rear of the unit.
2 Plug the other end into AC outlet.
To other Pioneer
component equipped
with CONTROL IN jack
Remote control for
AV amplifier, etc.
Point the remote
control toward the
signal receiver on
the AV amplifier, etc.
Other Pioneer component
equipped with CONTROL
IN/OUT jacks
PD-30
PD-30_PWSYXZT8.book 5 ページ 2012年5月7日 月曜日 午前11時33分
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer PD-30-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer PD-30-K in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 23,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer PD-30-K

Pioneer PD-30-K User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info