Manual Pioneer ND-BC8 (page 6 of 8) (English, German, French, Italian, Spanish)

699600

Zoom out

Zoom in

1/8

<CJ-E09S58R> <1313991023> <23> <CJ-E09S58R> <1313991023> <24><CJ-E09S58R> <1313991023> <21> <CJ-E09S58R> <1313991023> <22>

Fig. 11

Abb. 11

1 Pull out from here

2 Hinge

3 Harness cover

5 Hatch

4 Rear view

camera

2 Waterproof pad

Fig. 12

Abb. 12

1 Clamps

3 Rubber packing

4 Make a U-shaped loop in

the lead outside the rubber

packing to prevent rainwa-

ter from flowing along the

lead into the interior of the

vehicle.

Attach the waterproof pad

using double-sided tape.

Connection <ENGLISH>

Notes:

• This unit is for vehicles with a 12-volt battery and nega-

tive grounding. Before installing it in a recreational vehi-

cle, truck, or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to discon-

nect the battery cable before beginning installation.

• Refer to the owner’s manual for details on connecting the

other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To

protect the wiring, wrap adhesive tape around them where

they lie against metal parts.

• Route and secure all wiring so it cannot touch any mov-

ing parts, such as the gear shift, parking brake and seat

rails. Do not route wiring in places that get hot, such

as near the heater outlet. If the insulation of the wiring

melts or gets torn, there is a danger of the wiring short-

circuiting to the vehicle body.

• Do not shorten any leads.

• Never feed power to other equipment by cutting the insu-

lation of the power supply lead of the unit and tapping

into the lead. The current capacity of the lead will be

exceeded, causing over heating.

• When replacing the fuse, be sure to only use a fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA power supply cable as far away

from each other as possible.

• Connection to a TV with an RCA video input is possible,

but confirm whether the TV you use has a reverse gear

connection function.

• If this unit is installed in a vehicle that does not have an

ACC (accessory) position on the ignition switch, the red

lead of the unit should be connected to a terminal coupled

with ignition switch ON/OFF operations. If this is not

done, the vehicle battery may be drained when you are

away from the vehicle for several hours.

ACC position No ACC position

• Cords for this product and those for other products may

be different colors even if they have the same function.

When connecting this product to another product, refer to

the supplied manuals of both products and connect cords

that have the same function.

Connection sample (Fig. 9)

1 Rear view camera

Video input jack

Connect to camera input jack (REAR

VIEW CAMERA IN).

2 RCA pin

Accessory power supply

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

3 Red

4 Fuse (1 A)

Ground

To vehicle (metal) body.

5 Black

Cord installation (Fig. 10)

1 Clamps

2 Rear view camera

3 RCA power supply cable

4 Product with a video input jack

(Hideaway unit etc.)

5 Made with a rasp etc.

6 Scuff plate

7 Clamp

8 Waterproof pad

Attach the waterproof pad using double-

sided tape.

Cord installation points (Fig. 11, Fig. 12)

• When pulling the cord out of the car,

pull from the outer side of the hatch har-

ness cover and hinge. (Fig. 11)

1 Pull out from here

2 Hinge

3 Harness cover

4 Rear view camera

5 Hatch

• When the rear view camera cord cannot

be pulled out from the lower side, bend

the cord into a U shape in front of the

waterproof pad, making sure that rainwater

cannot enter the car by running down the

cord. (Fig. 12)

1 Clamps

2 Waterproof pad

3 Rubber packing

4 Make a U-shaped loop in the lead outside

the rubber packing to prevent rainwater from

flowing along the lead into the interior of the

vehicle.

Attach the waterproof pad using double-

sided tape.

After cord installation

Open and close the hatch door slowly to confirm

that the cord is not rubbing against the rim of

the door.

Power source ........................................... 14.4 V DC

(10.8 V to 15.1 V allowable)

Grounding system .............................. Negative type

Max. current consumption ............... 100 mA or less

Output video ....................................... Mirror image

(for rear view confirmation)

Sensor ......................... 1/4-inch color CMOS sensor

No. of pixels

..................effective no. of pixels roughly 310 000

Lens ........................................................ Wide-angle,

focal length f = 1.12 mm, F value 2.3

Angle of view .................. Horizontal: approx. 129 º

Vertical: approx. 105 º

IR cutoff filter (special filter for vehicle mounting)

.................................................................. Provided

Iris system .......................................... Electronic iris

Scanning system ........................................ Interlace

Synchronizing system ....... Internal synchronization

Signal-to-noise ratio .......................... 40 dB or more

(at the recommended intensity of illumination)

Horizontal resolution ............ Approx. 350 TV lines

Illumination range .... Approx. 0.9 lux to 100 000 lux

Image output ........ NTSC compatible 1 Vp-p (75 Ω)

Operation temperature range ......... –30 ºC to +70 ºC

–22 ºF to +158 ºF

Storage temperature range ............ –40 ºC to +85 ºC

–40 ºF to +185 ºF

Dimensions (W × H × D)

..................... 23.8 mm × 23.8 mm × 25.5 mm

(7/8 in. × 7/8 in. × 1 in.)

Weight ................................................. 186 g (0.4 lbs)

(including the cable)

Length

Rear view camera cable .......... 3 m (9 ft. 10 in.)

RCA power supply cable ...... 7 m (22 ft. 12 in.)

Note:

Specifications and the design are subject to possible

modification without prior notice due to improve-

ments.

Specifications <ENGLISH>

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer ND-BC8 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer ND-BC8 Manual

Product: