En En En En
Basic Settings
Basic settings refer to those settings that are
mandatory
setup. These settings can be changed later
A. Centerline
Adjust the monitor connected to the rear view
camera.
displayed in the center of the screen.
Note:
The centerline serves as a reference for vehicle
width when parked (orange line).
1. Press the ENTER b
2. Adjust so that the centerline is in the
center of the screen using the + and
– buttons.
Adjust so that the number of lines is the
same on both sides of the screen.
Note:
Adjustment can be made within the range of –63
to +63.
3. Press the ENTER b
When performing this procedure starting
from “First T
section B entitled “Position (Rotate)”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
B. Position (Rotate)
Adjust the rotation of the rear view camera
image as viewed from the location where the
rear view camera is installed.
1. Press the ENTER b
2. Adjust the angle with the + and
– buttons.
•
•
Adjust the angle so that an object (such as
the tire blocks) serving as a reference along
the horizontal lines is displayed.
Horizontal lines
Note:
Adjustment can be made within the range of –511
to +511.
Some portions may not be able to be seen depend-
ing on the settings.
3. Press the ENTER b
When performing this procedure starting
from “First T
section C entitled “Position (Horizontal)”.
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
C. Position (Horizontal)
Adjust the horizontal of the rear view camera
image as viewed from the location where the
rear view camera is installed.
1. Press the ENTER b
2. Adjust the horizontal position with
the + and – buttons.
Adjust so that the center of the parking
space is displayed in the center of the
camera screen in the horizontal direction.
Horizontal direction centerline
Note:
Adjustment can be made within the range of –63
to +63.
•
•
•
3. Press the ENTER b
When performing this procedure starting
from “First T
section D entitled “V
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
D. View Diagonal
Adjust the inclination of the rear view camera
image as viewed from the location where the
rear view camera is installed.
1. Press the ENTER b
2. Adjust view diagonal with the + and
– buttons.
Adjust view diagonal so that the white
lines of the parking space are displayed
symmetrically
Centerline
Note:
Adjustment can be made within the range of –255
to +255.
3. Press the ENTER b
When performing this procedure starting
from “First T
section E entitled “V
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
•
E. View Angle
Adjust the view angle (high angle mode) as
viewed from directly o
1. Press the ENTER b
2. Adjust the angle with the + and
– buttons.
Adjust the angle so that the white lines are
aligned with the vertical lines.
V
Note:
Adjustment can be made within the range of –511
to +511.
3. Press the ENTER b
When performing this procedure starting
from “First T
F entitled “V
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
•
F
Adjust the width within the vertical guidelines.
1. Press the ENTER b
2. Adjust the position with the + and
– buttons.
Adjust the position using the white lines of
the parking space as a reference.
V
Note:
Adjustment can be made within the range of –255
to +255.
3. Press the ENTER b
4. Press the ENTER b
When performing this procedure starting
from “First T
of “First T
When performing this procedure starting
from “Changing Basic Settings or Other
Settings”, return to step 5 of “Changing
Basic Settings or Other Settings”.
•
Changing Basic Settings or
Other Settings
Basic settings set during initial setup can be
changed. In addition, other settings can also
be made such as
Guideline (Shape) on “
Begin the setup procedure after parking the
vehicle at the location where photographs
are to be taken by referring to the section on
“Preparations Before Beginning Setup”.
1. Put the vehicle in r
Note:
When performing setup, always make sure to set
the parking brake and step on the brake to make
sure the car is stopped.
2. Simultaneously press the ENTER
and + buttons.
3. Press the ENTER b
4. T
T
T
section on “T
5. Select the parameter to be set with
the + and – buttons and then pr
the ENTER button.
Basic Settings
Set the basic settings
while referring to
“Basic Settings”.
6. Select OK and press the ENTER
button.
The settings are stored in memory
Note:
Please make sure to read the caution and then
press the ENTER button to go to the ne
Photograph data is deleted when setup is ended.
This camera and associated electronic guides are
intended solely as a driving aid.
a substitute for you attentiv
care while driving, mo
cle.
laws, e
•
•
•
•
Advanced Settings
Advanced settings such as
and Guideline (Shape) can be set using
advanced settings.
A. View (Wide/Zoom)
This adjustment is only necessary when only
ground is displayed or when the display is too
small or illegible when vie
angle mode because of the height of the rear
view camera.
1. Press the ENTER b
2. Adjust the view elevation with the +
and – buttons.
Note:
Adjustment can be made within the range of –63
to +63.
3. Press the ENTER b
Return to step 5 of “Changing Basic
Settings or Other Settings”.
B. Guideline (Shape)
Adjust the inclination of the vehicle v
guidelines (shape) when there is a considerable
discrepancy with the v
back of the field of vie
1. Press the ENTER b
2. Adjust the angle with the + and
– buttons.
V
Note:
Adjustment can be made within the range of –127
to +127.
3. Press the ENTER b
4. Press the ENTER b
Return to step 5 of “Changing Basic
Settings or Other Settings”.
Note:
The vertical guidelines (shape) setting reflect the
screen display of view angle and v
(width).
•
•
•
C. Guideline (Distance)
The distance between the horizontal guidelines
can be adjusted. The horizontal guidelines are
displayed at the interval sho
the initial setup when the camera has been
installed at the position shown in Fig. 1.
Fig. 1
1.5 m / 5 ft.
50˚
Approx.
1 m / 3 ft.
Approx.
1 m / 3 ft.
Fig. 2
Approx.
2 m / 7 ft.
Note:
The horizontal guidelines consist of three refer-
ence lines that serve as a reference when parking
(green, yellow and red lines).
In the case the “view angle” of the basic settings
has been adjusted from the factory adjustment,
the distances between the horizontal guidelines as
shown in Fig. 2 (approx. 1 m, 1 m and 2 m) will
be different.
1. Press the ENTER b
2. Adjust the angle with the + and
– buttons.
Horizontal guidelines
Note:
Adjustment can be made within the range of –255
to +255.
3. Press the ENTER b
4. Press the ENTER b
Return to step 5 of “Changing Basic
Settings or Other Settings”.
•
•
•
Advanced Settings
Set the advanced settings
while referring to
“
