811500
6
Zoom out
Zoom in
Previous page
1/8
Next page
Fig. 16
Abb. 16
Fig. 17
Abb. 17
Fig. 18
Abb. 18
Fig. 19
Abb. 19
Pull out from here Hinge
Harness cover
Hatch
Rear view
camera
Rear view camera
Hatch
Cord
Waterproof pad
Fig. 20
Abb. 20
Plastic clamp
Rubber packing
Make a U-shaped loop in
the lead outside the rubber
packing to prevent rain-
water from flowing along
the lead into the interior
of the vehicle.
Connection <ENGLISH>
Note:
This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recreational
vehicle, truck, or bus, check the battery voltage.
To avoid shorts in the electrical system, be sure to
disconnect the battery cable before beginning
installation.
Refer to the owner’s manual for details on connecting the
other units, then make connections correctly.
Secure the wiring with cable clamps or adhesive tape. To
protect the wiring, wrap adhesive tape around them where
they lie against metal parts.
Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and seat
rails. Do not route wiring in places that get hot, such
as near the heater outlet. If the insulation of the wiring
melts or gets torn, there is a danger of the wiring short-
circuiting to the vehicle body.
Do not shorten any leads.
Never feed power to other equipment by cutting the
insulation of the power supply lead of the unit and
tapping into the lead. The current capacity of the lead will
be exceeded, causing over heating.
When replacing the fuse, be sure to only use a fuse of the
rating prescribed on the fuse holder.
To minimize noise locate the TV antenna cable, radio
antenna cable and RCA power supply cable as far away
from each other as possible.
Connection to a TV with an RCA video input is possible,
but confirm whether the TV you use has a reverse gear
connection function.
If this unit is installed in a vehicle that does not have an
ACC (accessory) position on the ignition switch, the red
lead of the unit should be connected to a terminal coupled
with ignition switch ON/OFF operations. If this is not
done, the vehicle battery may be drained when you are
away from the vehicle for several hours.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
Cords for this product and those for other products may
be different colors even if they have the same function.
When connecting this product to another product, refer to
the supplied manuals of both products and connect cords
that have the same function.
Connection sample (Fig. 16)
Image processing unit power supply
Rear view camera connector
RCA power supply cable connector
Rear view camera
Button unit
Button unit connector
Video input jack
Connect to video input jack.
RCA pin
Accessory power supply
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
Red
Fuse (1A)
Ground
To vehicle (metal) body.
Black
Cord installation (Fig. 17)
Plastic clamps
Rear view camera
RCA power supply cable
Product with a video input jack
(Hideaway unit etc.)
Image processing unit power supply
Button unit
Made with a rasp etc.
Scuff plate
Plastic clamp
Waterproof plate
Double-sided tape (rectangular)
Cord installation points (Fig. 18)
When pulling the cord out of the car,
pull from the outer side of the hatch
harness cover and hinge.
Pull out from here
Hinge
Harness cover
Rear view camera
Hatch
After cord installation (Fig. 19, Fig. 20)
Open and close the hatch door slowly
to confirm that the cord is not rubbing
against the rim of the door.
Rear view camera
Hatch
Cord
When the rear view camera cord cannot
be pulled out from the lower side due to
the type of car.
As shown in the figure 18, bend the cord
into a U shape in front of the waterproof
pad, making sure that rain water cannot
enter the car by running down the cord.
Plastic clamp
Waterproof pad
Rubber packing
Make a U-shaped loop in the lead outside
the rubber packing to prevent rainwater from
flowing along the lead into the interior of the
vehicle.
Image processing unit power supply
RCA power supply
cable connector
Rear view camera
connector
Button unit
connector Button unit
Red
RCA pin
Black
Fuse (1A) 3 m (9 ft. 10 in.)
3 m (9 ft. 10 in.)
Rear view camera
1.5 m (4 ft. 11 in.)
7 m (23 ft.)
Plastic clamps
Rear view
camera
Product with a video input
jack (Hideaway unit etc.)
Made with a rasp etc.
Scuff plate
Plastic clamp Waterproof plate
RCA power
supply cable
Image processing unit power supply
Button unit
4 m (13 ft. 2 in.)
Double-sided
tape (rectangular)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer ND-BC20PA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer ND-BC20PA in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer ND-BC20PA

Pioneer ND-BC20PA User Manual - English, Spanish - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info